The Non-Production Fuel Reprocessing Program involves the chemical processing of valuable reactor fuels received from privately owned power reactors. It is necessary therefore, to accurately measure the fuel material received in order to insure proper payment to reactor operator and to provide the Atomic Energy Commission with appropriate accountability data. The volume measurement study described herein was conducted in order to determine the limits of accuracy that could be obtained in measuring relatively large volumes of solution under plant processing conditions.

The following report provides information on an aerosol generator fit to produce fine particles by a vaporization-condensation technique. Included is a diagram of the essential components of the generator.

The successful completion of a program of experiments, including the Aircraft Reactor Experiment (ARE), has demonstrated the high probability of producing militarily useful aircraft nuclear power plants employing reflector-moderated circulating-fuel reactors. Consequently, and accelerated program culminating in operation of the Aircraft Reactor Test (ART) is under way. In order to adhere to the compressed schedule of the accelerated program, it is essential that the Atomic Energy Commission approve the 7500 Area in Oak Ridge as the test site by February15, 1955. This report summarizes the hazards associated with operating the contained 60-Mv reactor of the ART at the proposed Oak Ridge test site.

Abstract: Information on five uranium binary alloy systems has been surveyed. These systems are the alloys of uranium with zirconium, chromium, columbium, vanadium, and molybdenum. The equilibrium diagrams are discussed, and where available, data have been included on diffusion studies, cladding experiments, and mechanical properties.

Technical report describes how glasses and crystals subjected to ionizing radiation develop absorption bands and become colored. The coloring of defects can be used to determine how nuclear reactor induced defects anneal out or disappear as an irradiated sample is heated.

From introduction: "In this paper the adaptation of the wax lab surface vibratory polisher is described. The wax lap requires little maintenance during the life of the lap. It is not necessary to remove any of the holding devices on the bowl to clean and recondition the lap. The bowl is merely washed out, recharged and placed in operation. The wax lap will not wrinkle or tear, nor is it necessary to change it each day such as the silk or nylon cloths."

Abstract: The results of both dry and wet attritioning of Temple Mountain ore are presented. In order to obtain effective attritioning on this ore, the amphaltite must be removed before attritioning. With the asphaltite present, dry attritioning causes a build-up of asphaltite on the surface of sand grains, with consequent loss of uranium values. In wet attritioning, the asphaltite is not broken down or attritioned, because of its low specific gravity and resilience.

Technical report investigates creating a microbeam of deuterons to simulate cosmic rays and the results of brain irradiation, irradiation of the eye, and irradiation of hair follicles of mice. The report's conclusion was that "astronauts exposed to heavy primary particles over a period of some weeks would be expected to develop gray hairs, but this is the only significant biological damage they would suffer."

This technical report introduces "some approximations into the basic quantum mechanical theory" so that the theory of the covalent bond and the molecular orbital method "can be combined into one which will yield quantitative rather than qualitative binding energies and cohesive energies and also distinct energy levels and band structure." This approach will provide a common method "suitable to both solid state physicists and physical chemists, for calculating the energy levels in metals and complex molecules." This report also contains figures detailing the findings. (Quotations taken from introduction)

A simplified method was developed for calculating wall-scatter gamma radiation escaping through a shield opening. The method was applied to the HRT and the results showed that next to the line of sight contribution, scattering of the wall of the shield opening was the main contribution to the dose at the rear edge of the shield. Design charts were prepared that give the dose as a function of the gamma source location with the reactor cell.

The cup assembly of the Experimental Breeder Reactor (EBR) consists of blanket bricks, inner rings, and safety plug, all of natural uranium. The design of the finish machined brick is shown in Figure 1. These pie shaped bricks when stacked together, 12 bricks arranged in circular form and stacked seven rings high, comprise the cylindrical portion of the outer blanket, 17.875" I.D. x 30.875" O.D. after machining and canning. The inner ring, which is shown in Figure 2, fits inside the bottom layer of bricks. The circular opening in the center of the inner ring is closed by the safety plug shown in Figure 3.

This technical report introduces a new method to capture entire cell populations in the intestines of rats, which have been continuously exposed to radiation.This report finds that the "total number of cells per crypt found after 5 days of irradiation decreases with increasing dose rate." This report includes four figures and two tables detailing findings.

This report was written by different scientist on various experiments of solid state, physical chemistry, radiochemistry and analytical, and special problems.

The following report describes tests made for the purpose of determining the accuracy and permanency of various types of high resistance bleeders, and their resistance variation during use over a period of approximately six months.

From introduction: "This conference represents the first attempt by a project-wide group of scientists and engineers to collaborate on the problem associated with the planning and design of "Hot" Laboratories. The idea, as originally conceived by Dr. W. E. Winsche, was to discuss some general and perhaps some specific aspects of "Hot" Laboratory design with a small group of interests individuals from various sites."

Abstract: "The results obtained from the tests conducted for the purpose of determining the corrosivity of a 30 percent-solution of uranyl fluoride to various metals indicate that stainless steels (type 302, 304, 321 and 316) have very good resistance; while monel, nickel and aluminum, respectively, exhibit diminishing resistance. Stainless steel, type 316, was the most resistant of the specimen tested."

The conventional volumetric micro-determination of phosphate depends upon the precipitation of phosphomolybdate, filtration and washing of the precipitate, and titration with standard base. The method is slow and tedious, subject to many interferences, and is not applicable to samples containing less than 1-2 mg of phosphate. Other weak acid anions, such as carbonate or acetate, interfere in the method. Strong acid anions, such as nitrate, sulfate, and chloride do not interfere.

From abstract: "A continuous countercurrent solid-liquid contactor has been developed which retains the desirable features of the conventional fixed bed and gains the advantages of countercurrent flow. It can be adapted to many solid-liquid mass-transfer processes such as ion exchange, silica gel adsorption, and ore leaching."

The tendency for Austenitic Stainless Steels to develop cracks may be considered to be a function of several variables. Chemical composition of the electrode and base metal, are variables which have been reported to greatly influence the final behavior of the weld. Two types of electrodes, Type 308L and Type 347, were compared with respect to their respective crack sensitivities. Also, comparative results were desired between the 308L-15 (DC) and 308L-15 (AC-DC) type electrodes. At present, no standard test has been designed that will yield quantitative results as to the crack-resistant properties of a weld. With this in mind, the "Arcos Segmented Circular-Groove Notch Sensitivity Test" was chosen as the test to be used, since other investigations have employed the test and some comparison of results could be made.

Abstract: "The structure of an extremely strong magnetohydrodynamic shock is discussed in the limit of no particle collisions. It is tentatively concluded that the shock transition takes place through the mechanism of a strong electric field produced by charge separation. The pressure in the shocked plasma is due primarily to a very high electron temperature. The ions, on the other hand, undergo an irreversible temperature change of only 3."

The transfer or circulation of raw dissolver solutions containing gross particulate matter presents many problems not easily overcome by standard pumping equipment. In April of 1956 the HAPO concept of a modified Archimedes screw pump was developed. Two basic models, externally powered and driven through extended shafts, were constructed and tested. Operation of these preliminary models was so satisfactory that a third unit, integrally formed into drive motor, was built and placed in extended life test. This report describes construction and testing of the third and final model.

Abstract: "This is a selective bibliography of books and periodical articles relating to die design of hot presses. Sources consulted include: ASM Review of Metal Literature, 1950-1954; Chemical Abstracts, 1950-1055; Engineering Index, 1950-1055; Industrial Arts Index, 1950-March 1957; Metallurgical Abstracts, 1950-1953; Nuclear Science Abstracts, 1950-March 1957; Physics Abstracts, 1950-1955; the library card catalog, and the Technical Information Division AEC card catalog."

The thickness of an oxide film on phosphor bronze helices was determined by first establishing the oxygen content of the helix "as received" and after cleansing with nitric acid. Based on the assumption that the difference between these two values was the oxygen in the film, and that the film consisted entirely of cupric oxide, the thickness of the film was calculated from the density of cupric oxide, weight of the film, and surface area of film. A value of 1080 A was calculated as the thickness by this method.

Abstract: "Neutron nonelastic cross sections measured at different detector biases have been used to determine the cross sections for inelastically scattering 14 Mev neutrons into 9- to 14-Mev energy range. The cross section for producing these high energy neutrons, which may be attributed to direct interaction processes, is roughly 10% of the nonelastic cross section, for all elements. A comparison is made with data of Coon and co workers, who measured angular distributions for the same high-energy inelastically scattered-neutron group."