This volume continues the NACA study of combustion principles for aircraft propulsion. The various aspects of combustion pertinent to jet engines are organized and interpreted with quite extensive information, particularly for basic or fundamental. subject matter. The report concerns only air-breathing engines and hydrocarbon fuels, and not rocket engines and high-energy fuels.

From Introduction: "Presented in this report are the basic data obtained from investigation. The data are presented with limited analysis in order to expedite their availability to those concerned with jet-exit-afterbody design."

From Introduction: "In the present investigation, lift, drag, and pitching moment were determined over a Mach number range 0.6 to 1.42. Smooth-water takeoff and landing stability and resistance were investigated. A brief check of the rough-water spray and behavior was also made."

"An investigation has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel to determine the control effectiveness and hinge-moment characteristics of the Martin XASM-N-7 (Bullpup) missile. A half-scale wing panel was tested with a tip control having three different hinge-line locations. The tests were made over an angle-of-attack range from -10 to 10 degrees and a control-deflection range of -15 to 3 degrees" (p. 1).

"Tests have been made in the Langley 4- by 4-foot supersonic pressure tunnel at Mach numbers of 1.41, 1.61, and 2.01 to determine the static longitudinal stability and control characteristics of various arrangements of the Grumman F11F-1 airplane. Tests were made of the complete model and various combinations of its component parts and, in addition, the effects of various body modifications, a revised vertical tail, and wing fences on the longitudinal characteristics were determined" (p. 1).

Report discussing testing of a scale model of the Convair F-102B to determine its aerodynamic characteristics at several Mach numbers. Four basic body modifications and two afterbody configurations were evaluated.The body modifications were all found to slightly reduce values of minimum drag, but did not cause a change in the static stability and lift-curve-slope values compared to the F-102A.

Memorandum presenting an investigation of the flow characteristics over a 6-percent-thick symmetrical circular-arc airfoil section with a 30-percent-chord trailing-edge flap at a Mach number of 6.90 and a Reynolds number of 1.65 x 10(sub 6). The model was tested over an angle-of-attack range of 0 to 16 degrees and a flap-deflection range of -16 degrees to 16 degrees. Results regarding pressure results and aerodynamic characteristics are provided.

From Introduction: "The purpose of this paper is to discuss and evaluate some of the input signals or control parameters which have been experimentally employed to operate turbojet inlet-control systems. These include the normal-shock position, the oblique-shock position, and the diffuser-exit Mach number. The discussion is based on results obtained at the NACA Lewis laboratory during control investigations of ram-jet engines (ref. 1 to 5) and during a study on the control of a supersonic inlet for the J34 turbojet engine (refs 6 and 7)."

Memorandum presenting tests at two supersonic speeds to obtain experimentally the aerodynamic damping characteristics of a control surface on a two-dimensional wing. The control surface had a chord of 1.67 inches and a span of 7.25 inches and was supplied in three materials with different mass, inertia, and stiffness properties. Results regarding the presentation of data and comparison with theory and comparison with control-surface data for a triangular wing are provided.

Compendium presenting a comprehensive integration of available aerodynamic design information on axial-flow compressors. The subjects of the first volume of this investigation are objectives and scope, compressor design requirements, compressor design system, potential flow in two-dimensional cascades, and viscous flow in two-dimensional cascades.

"Available experimental two-dimensional-cascade data for conventional compressor blade sections are correlated. The two-dimensional cascade and some of the principal aerodynamic factors involved in its operation are first briefly described. Then the data are analyzed by examining the variation of cascade performance at a reference incidence angle in the region of minimum loss" (p. 1).

Chapters XI to XIII concern the unsteady compressor operation arising when compressor blade elements stall. The fields of compressor stall and surge are reviewed in Chapters XI and XII, respectively. The part-speed operating problem in high-pressure-ratio multistage axial-flow compressors is analyzed in Chapter XIII. Chapter XIV summarizes design methods and theories that extend beyond the simplified two-dimensional approach used previously in the report. Chapter XV extends this three-dimensional treatment by summarizing the literature on secondary flows and boundary layer effects. Charts for determining the effects of errors in design parameters and experimental measurements on compressor performance are given in Chapters XVI. Chapter XVII reviews existing literature on compressor and turbine matching techniques.

Report presenting the aerodynamic heat-transfer properties and zero-lift drag of a typical pilot's canopy as determined by a rocket-model flight test through a range of Mach and Reynolds numbers. The canopy had a 63 degree sweptback flat windshield, circular cross section, and an equivalent body fineness ratio of 7.0. Results regarding the canopy temperature distribution, canopy pressure distribution, heat-transfer coefficient, and drag are provided.

From Introduction: "The primary purpose of the wing instrumentation was to obtain data for use in design of NACA research missiles; however, it is believed that the wing is representative of typical supersonic designs and that the data will be of general use and interest. Only the wing data are reported herein."

From Introduction: "The purpose of this paper is to review new and significant data which will be of interest to designers in determining the heating of these components. A comparison with existing theory to indicate its adequacy in each case is also presented."

Report presenting an investigation at two Mach numbers to examine the flow, force, and moment characteristics associated with spoilers mounted on a flat plate at a range of sweep angles. Pressure measurements were obtained over the plate and spoiler faces. The pressures were integrated to determine the spoiler lift, pitching-moment, drag, and hinge-moment characteristics.

Report presenting an investigation to determine separately the aerodynamic characteristics of a Douglas Aircraft Company store and a semispan delta-wing-fuselage configuration in the presence of one another. The store was located at the 50-percent-semispan station with the store nose both ahead of and behind the wing leading edge for two longitudinal and three vertical positions.

Report presenting an investigation to determine the aerodynamic characteristics of a sting-mounted Douglas Aircraft Company store in the presence of an unswept semispan cantilevered wing of aspect ratio 4.0. Results regarding wing loads and store loads are provided.

Memorandum presenting an investigation in the blowdown tunnel of the pressure tunnel to determine the aerodynamic characteristics of a sting-mounted Douglas Aircraft Company store in the presence of, but not attached to, an unswept semispan cantilevered wing of aspect ratio 4.0. The influence of the store on the aerodynamic characteristics of the wing was also obtained.

From Introduction: "It is the purpose of this report to assemble principles of induction-system design for flight to a Mach number of 2 and to use existing data to show the consequences of compromising them."

Jet engine induction systems investigations and relationship of air inlets, drag, airframe, pressure recovery, flow and interferences.

From Introduction: "The primary purpose of this paper is to describe progress in the aerodynamics of wings, bodies, and wing-body combinations at high angles of attack."

Memorandum presenting wind tunnel tests performed on a family of missiles. This paper summarizes some of the performance and stability and control characteristics of the missiles.

Effect of variation of combustion chamber length and inlet temperature on low pressure-loss sea level afterburner. A 70-percentage-point reduction in combustion efficiency resulted when the combustion-chamber length was reduced from 62 to 10 inches.