This report details the acceleration data collected from racing airplanes during actual races. The data was collected in order to make recommendations regarding the structural safety of racing airplanes and the methods of operating racing airplanes that reduces the probability of subjecting them to extreme air loads. The records do not lead to any conclusions regarding maximum air loads.

"Flight tests of a Grumman Scout (XSF-2) airplane fitted with a Pratt & Whitney 1535 supercharged engine were conducted to determine the effect of engine power, mass flow of the cooling air, and atmospheric temperature on cylinder temperature. The tests indicated that the difference in temperature between the cylinder wall and the cooling air varied as the 0.38 power of the brake horsepower for a constant mass flow of cooling air, cooling-air temperature, engine speed, and brake fuel consumption. The difference in temperature was also found to vary inversely as the 0.39 power of the mass flow for points on the head and the 0.35 power for points on the barrel, provided that engine power, engine speed, brake fuel consumption, and cooling-air temperature were kept constant" (p. 1).

"Systematic flight investigation of the spinning characteristics of various airplanes over a period of several years have given the pilots engaged in the testing a varied and extensive experience. From this experience certain general rules of procedure have been formulated, particularly for the sequence of operation of the controls in recovery from spins, and are recommended to the attention of all pilots" (p. 1).

Many technical papers on the various phases of airplane take-off have been published. Frequently, however, there appear new ideas which affect only particular scattered phases of the subject and which do not receive individual publication. It is the purpose of this paper to present several ideas of this nature which may be of considerable aid in calculating take-off performance and one idea which should correct what appears to be a popular misconception of the importance of static propeller thrust.

"The results of tests made to determine the performance of a DePalma-Roots supercharger are presented. The performance of the DePalma supercharger with atmospheric pressure at the discharge was compared with that of a hypothetical NACA Roots-type supercharger of the same displacement. The tests were conducted at speeds from 1,000 to 6,000 r.p.m. and at pressure differences from 0 to 15 inches of mercury" (p. 1).

"A 1/7.06 full-size model of the NC-type hull was tested in the N.A.C.A. tank by both the general method and the specific or free-to-trim method. The results of the tests are given in curves plotted as non dimensional coefficients and are compared with the test results of N.A.C.A. model 11-A. The NC model (N.A.C.A. model 44) shows higher resistance than model 11-A at hump speed but lower resistance at high speeds. Model 44 has a higher best trim angle at the jump and a lower maximum positive trimming moment than model 11-A. At high speeds the best trim angle and the trimming moments of the two models are approximately the same" (p. 1).

The results of tests of six airfoils having the N.A.C.A. 230 mean line and varying in thickness from 0.06c to 0.21c are presented. These results agree with previous findings in showing that aerodynamically the best section is one of moderate thickness. The data are of value mainly in connection with the design of tapered wings having sections based on the N.A.C.A. 230 mean line.

"The development of metal construction for aircraft has created a need for accurate and detailed information regarding the strength of riveted joints in aluminum-alloy structures. To obtain this information the National Bureau of Standards in cooperation with the National Advisory Committee for Aeronautics is investigating the strength of riveted joints in aluminum alloys. The strength of riveted joints may be influenced by the form of the head, the ratio of the rivet diameter to the sheet thickness, the driving stress, and other factors" (p. 1).

"It is shown that the control force of ordinary ailerons may be reduced to zero over a range of deflections and at a given flight condition by the use of an appropriate differential movement. Approximations to the ideal motion obtainable with a simple linkage are discussed and a chart that enables the selection of an appropriate crank arrangement is presented. Various aspects of the practical application of the system are discussed and it is concluded that a small fixed tab, deflected to trim both ailerons upward, would be advantageous" (p. 1).

"A resume of the equations and formulas for the forces and moments on an aircraft-engine mount is presented. In addition, available experimental data have been included to permit the computation of these forces and moments. A sample calculation is made and compared with present design conditions for engine mounts" (p. 1).

"In order to determine whether or not flaps could be expected to have any beneficial effect on take-off performance, the distances required to take off and climb to an altitude of 50 feet were calculated for hypothetical airplanes, corresponding to relatively high-speed types and equipped with several types of flap. The types considered are the Fowler wing, the Hall wing, the split flap, the balanced split flap, the plain flap, and the external-airfoil flap. The results indicate that substantial reductions in take-off distance are possible through the use of flaps, provided that the proper flap angle corresponding to a given set of conditions is used" (p. 1).

From Summary: "Performance tests were made using a rectangular displacer arranged so that the combustion air was forced through equal passages at either end of the displacer into the vertical-disk combustion chamber of a single-cylinder, four-stroke-cycle compression-ignition test engine. After making tests to determine optimum displacer height, shape, and fuel-spray arrangement, engine-performance tests were made at 1,500 and 2,000 r.p.m. for a range of boost pressures from 0 to 20 inches of mercury and for maximum cylinder pressures up to 1,150 pounds per square inch. The engine operation for boosted conditions was very smooth, there being no combustion shock even at the highest maximum cylinder pressures. Indicated mean effective pressures of 240 pounds per square inch for fuel consumptions of 0.39 pound per horsepower-hour have been readily reproduced during routine testing at 2,000 r.p.m. at a boost pressure of 20 inches of mercury."

"A series of tests was made in the N.A.C.A. free spinning tunnel to find the effect upon spinning characteristics of systematic changes in tail arrangement. The tests were made with a 1/16-scale made of a low-wing monoplane of modern design. The changes consisted of: (1) variation of the fuselage length; (2) variation of the fore-and-aft location of the vertical surfaces; and (3) variation of the vertical location of the horizontal surfaces. The spinning characteristics of the model, including the number of turns required for recovery, were found to vary systematically and regularly with systematic changes in the tail arrangement" (p. 1).

An empirical method is given for estimating the aerodynamic effect of ordinary and split flaps on airfoils similar to the Clark Y. The method is based on a series of charts that have been derived from an analysis of existing wind-tunnel data. Factors are included by which such variables as flap location, flap span, wing aspect ratio, and wing taper may be taken into account. A series of comparisons indicate that the method would be suitable for use in making preliminary performance calculations and in structural design.

"An investigation was made to obtain information on the minimum quantity of air and power required to cool conventional air cooled cylinders at various operating conditions when using a blower. The results of these tests show that the minimum power required for satisfactory cooling with an overall blower efficiency of 100 percent varied from 2 to 6 percent of the engine power depending on the operating conditions. The shape of the jacket had a large effect on the cylinder temperatures. Increasing the air speed over the front of the cylinder by keeping the greater part of the circumference of the cylinder covered by the jacket reduced the temperatures over the entire cylinder" (p. 1).

Several improvements that have been made on commercially available carbon-monoxide indicators to make them more suitable for aircraft use are described. These improvements include an automatic flow regulator, which permits the use of a simplified instrument on aircraft where a source of suction is available, and a more reliable alarm attachment. A field method for testing instruments on standard samples of carbon monoxide is described. Performance data and instructions in operation and maintenance are given.

The sodium line-reversal method has been used in some preliminary measurements of flame temperature. Improvements in the method involving a photographic recorder and a means of correcting for the dirtiness of the windows are described. The temperatures so obtained are compared with those calculated from pressure diagrams.

"In the selection of materials for aircraft application, it is not enough to make the selection on a strength-weight basis alone. A strength-weight comparison is significant but other factors must be considered, for while a material with a high ratio of strength to weight may be perfectly satisfactory for one use, it may be totally unfitted for another. It is essential, among other things, that the probable nature, magnitude, and direction of the principal stresses be given special consideration" (p. 1).

Surveys of the air flow over the upper surface of four different airfoils were made in the full-scale wind tunnel to determine a satisfactory location for a fixed Pitot-static tube on a low-wing monoplane. The selection was based on small interference errors, less than 5 percent, and on a consideration of structural and ground handling problems. The most satisfactory location on the airfoils without flaps that were investigated was 10 percent of the chord aft and 25 percent of the chord above the trailing edge of a section approximately 40 percent of the semispan inboard of the wing tip. No satisfactory location was found near the wing when the flaps were deflected.

The definitions of flexural center, torsional center, elastic center, and elastic axis are discussed. The calculation of elastic centers is dealt with in principle and a suggestion is made for the design of shear webs.

"Large models of the Mark V and Mark VI floats used for single float seaplanes (National Advisory Committee for Aeronautics (NACA) models 41-A and 41-B, respectively) were tested in the NACA tank to provide general test data for typical single floats and a basis for possible improvements of their form. The resistance of model 41-B was greater than that of model 41-A, either when free to trim or at the best trim angle for each. The resistance of model 35-B (a pointed step hull tested free to trim) was less than either of the models at the hump speed, greater at intermediate planing speeds, and less at the speeds and loads near get-away, although the spray was generally worse owing to the absence of transverse flare" (p. 1).

From Summary: "The procedure for obtaining air-speed and rate-of-climb measurements in performance tests of airships is described. Two methods of obtaining speed measurements, one by means of instruments in the airship and the other by flight over a measured ground course, are explained. Instruments, their calibrations, necessary correction factors, observations, and calculations are detailed for each method, and also for the rate-of-climb tests. A method of correction for the effect on density of moist air and a description of other methods of speed course testing are appended."

"Preliminary tests have been made for the purpose of obtaining a flap arrangement suitable for direct and immediate control of the steepness of the glide path of an airplane, a use for which present flaps are not satisfactory. An attempt has been made to develop a flap giving a reasonably high maximum lift coefficient with relatively low deflection and maintaining this value of the maximum lift coefficient with a large increase of deflection, the increase in deflection being accompanied by a large increase in drag. An arrangement was found that gave a maximum lift coefficient of approximately 1.90 for all flap deflections between 25 and 80 degrees, within which range the drag of the wing increased regularly to a large value" (p. 1).

From Introduction: "The possibilities of the jump take-off have been established by some full-scale experiments. It is the purpose of this paper to study the factors that govern the jump take-off in its simplest form and to present the results of model tests in which the effect of differences in the rotor parameters was determined."