From Summary: "Two topics of interest to persons attempting to apply the heat method of preventing ice formation on aircraft are considered. Surfaces moving through air at high speed are shown, both theoretically and experimentally, to be subject to important aerodynamic heating effects that will materially reduce the heat required to prevent ice. Numerical calculations of the path of water drops in an air stream around a circular cylinder are given. From these calculations, information is obtained on the percentage of the swept area cleared of drops."

A preliminary investigation made to study the hydrodynamic properties and general behavior of simple hydrofoils. Six plain, rectangular hydrofoils were tested in a tank at various speeds, angles of attack, and depths below the water surface. The results are presented as curves of the lift and drag coefficients plotted against speed for various angles of attack and depths for which the hydrofoils were tested.

Drag testing was conducted in the high-speed wind tunnel of 23 conditions combining six streamline shapes and three conventional cowling-fuselage bodies. All of the models were tested in combination with a wing in order to include wing-fuselage interference effects. The critical speeds of combinations tested were, in general, determined by the wing-fuselage juncture.

Report presenting tests conducted in the 8-foot high-speed wind tunnel of a scale model pursuit-type fuselage with practicable internal duct arrangement designed to meet all of the air requirements of a 1000-horsepower radial engine submerged at the maximum section. The results showed that the required internal flow can be obtained with negligible ducting losses provided that basic principles are observed in designing the air passages.

Report presenting a series of boundary-layer surveys over the surface of an NACA 0012 airfoil at zero lift. Results regarding the pressure distribution, laminar boundary layer, transition, turbulent boundary layer, drag, and skin friction are provided.

"A study has been made of underslung cooling ducts with special references to the problems presented by the boundary layer on the fuselage skin. It was found that good flow can be obtained in such ducts by (1) making the inlet opening of such size that the mean inlet velocity is about 0.6 the free-stream velocity and (2) providing vanes behind as well as ahead of the radiator. Tables to facilitate design are included, together with an example " (p. 1).

Report presenting a study on wing-nacelle propeller arrangements using a two-engine airplane with nacelles varying in diameter. Results regarding the power-off characteristics, propulsive and overall efficiencies, power-on characteristics, and pressure distributions are provided.

"A unit injector was operated under various test conditions with a cam outline giving a high rate of plunger displacement. The rate of discharge of the unit injector followed the plunger displacement for the outwardly opening injection valve (open nozzle) except under conditions of high fuel pressures when the effect of fuel compressibility decreased the rate of discharge as the pressure increased. The rate of discharge for the inwardly opening injection valve (closed nozzle) did not directly follow the plunger displacement" (p. 1).

"The use of different forms of wide-flange, thin-wall steel beams is becoming increasingly widespread. Part of the information necessary for a national design of such members is the knowledge of the stress distribution in and the equivalent width of the flanges of such beams. This problem is analyzed in this paper on the basis of the theory of plane stress. As a result, tables and curves are given from which the equivalent width of any given beam can be read directly for use in practical design" (p. 1).

"A total of 183 panel specimens of 24ST aluminum alloy with nominal thickness of 0.020, and 0.040 inch with extruded bulb-angle sections of 12 shapes spaced 4 and 5 inches as stiffeners were tested to obtain the buckling stress and the amplitude of the maximum wave when buckled. Bulb angles from 3 to 27 1/2 inches long were tested as pin-end columns. The experimental data are presented as stress-strain and column curves and in tabular form" (p. 1).

"A compilation of the experimentally determined moments of inertia of 32 airplanes is presented. The measurements were obtained at the laboratories of the NACA by means of a pendulum method. The airplanes tested are representative of several types of aircraft of gross weight less than 10,000 pounds. The results are presented in coefficient as well as in dimensional form. An elementary analysis of the data disclosed the possibility of grouping the results according to wing type of the airplane, as low-wing monoplanes, parasol and high-wing monoplanes, and biplanes" (p. 1).

"The magnitude, the direction, and the fluctuations of tow forces exerted upon gliders by towing them aloft behind an automobile were measured under a variety of conditions covering a range from gentle to severe types of operation. For these tests, the glider towing force did not exceed 1.6 of the gross weight of the glider. V-G records obtained during the towed-flight period as well as during the subsequent return glide to earth showed accelerations in the range from 3 to -1 g. The results of preliminary airplane tow tests are also presented" (p. 1).

"An investigation of three methods for the prevention and the removal of ice on an airplane windshield has been completed. The methods were: electric heating; hot-air heating; and an alcohol-dispensing, rotating wiper blade. The results showed that vision through the airplane windshield could be maintained during severe icing conditions by the use of heat" (p. 1).

From Summary: "Methods are described for calculating the period and frequency of vibration of cantilever wings and similar structures in which the weight and moment of inertia vary along the span. Both the beam and torsional frequencies may be calculated by these methods. The procedure is illustrated by examples."

"Sound pressure of the first four harmonics of rotation from a full-scale two-blade propeller were measured and are compared with values calculated from theory. The comparison is made (1) for the space distribution with constant tip speed and (2) for fixed space angles with variable tip speed. A relation for rotation noise from an element of radius developed by Gutin is given showing the effect of number of blades on the rotation noise" (p. 1).

From Summary: "A discussion is given of the important aspects of the stalling of vertical tail surfaces. The type of instability encountered is described and the possibilities of inadvertent occurrence are noted. The influence of directional flight tests on the behavior of a airplane when the tail stall takes place is discussed. In this connection, flight tests of a twin-engine airplane in which the vertical fin area was increased are cited."

Note presenting the body of knowledge that has been accumulated in the field of noise reduction in aircraft. Special attention is paid to effective soundproofing schemes.

A new method of studying the flow of the water along the bottom of a model of a flying-boat hull is described. In this method, the model is fitted with a transparent bottom and is divided down the center line by a bulkhead. The flow is observed and photographed through one-half of the model by means of the diffused illumination from a battery of lamps contained in the other half of the model. Photographs of the flow, particularly of the changes that occur when the step ventilates, are shown. The results of the present investigation indicate that the method has considerable promise, chiefly in connection with motion-picture studies.

"The vortex theory as presented by the author in earlier papers has been extended to permit the solution of the following problems: (1) the investigation of the relation between thrusts and torque distribution and energy loss as given by the induction of helical vortex sheets and by the parasite drag; (2) the checking of the theorem of Betz of the rigidly behaving helical vortex sheet of minimum induced energy loss; (3) the extension of the theory of the screw propeller of minimum energy loss for the inclusion of parasite-drag distribution along the blades" (p. 1).

The problem of determining values of structural damping for use in flutter calculations is discussed. The concept of equivalent viscous damping is reviewed and its relation to the structural damping coefficient g introduced in NACA Technical Report No. 685 is shown. The theory of normal modes is reviewed and a number of methods are described for separating the motions associated with different modes. Equations are developed for use in evaluating the damping parameters from experimental data. Experimental results of measurements of damping in several flutter models are presented.

An investigation was made of a large-chord NACA 23030 airfoil with a 40- and a 25.66 percent-chord slotted flap to determine the section aerodynamic characteristics of the airfoil affected by flap chord, slot shape, flap position, and flap deflection. The flap positions for maximum lift, the position for minimum drag at moderate and high lift coefficients, and the complete section aerodynamic characteristics of selected optimum arrangements are given. Envelope polar of various flap arrangements are included. The relative merits of slotted flaps of different chords on the NACA 23030 airfoil are discussed, and a comparison is made of each flap size with a corresponding flap size on the NACA 23021 and 23012 airfoils.

Report presenting testing of a model of the two-stroke engine described in NACA Technical Note No. 674 for the purpose of observing the scavenging-air flow obtained with various inlet-port arrangements. Three types of cylinder head were tried with the round-edge piston in the engine. Results regarding the effect of port arrangement, pistons, cylinder-head shapes, effect of swirl, and exhaust restrictions are provided.

"An investigation has been made in the NACA 7- by 10-foot wind tunnel of a large chord NACA 23021 airfoil equipped with two arrangements of a completely extended 15 percent chord extensible flap. One of the flaps had a faired juncture, without a gap; the other was provided with a slot between the trailing edge of the airfoil and the nose of the flap. The results showed that the basic airfoil gave the lowest profile-drag coefficients over the low lift range, the airfoil with the plain extensible flap gave the lowest profile-drag coefficients over the moderate lift range, and the airfoil with the slotted extensible flap gave the lowest profile-drag coefficients over the high lift range" (p. 1).

From Summary: "The force variation along the wing span under combined normal and angular accelerations is considered. Non dimensional curves of section load, shear, and moment are given for: (1) the air load that produces a normal acceleration; (2) the accompanying wing weight and normal inertia loads; (3) aileron and gust air loads that produce angular acceleration; (4) the angular inertia load of the wing. The required aerodynamic load distributions have been obtained by use of wing theory, and the wing inertia distributions are based on an analysis of wing-weight data. Several examples are included to illustrate the effect of wing taper and aileron span on the total shears and moments at any section along the span."