In this report a method is presented for the calculation of the profile drag of airfoil sections. The method requlres only a knowledge of the theoretical velocity distribution and can be applied readily once this dlstribution is ascertained. Comparison of calculated and experimental drag characteristics for several airfoils shows a satisfactory agreement. Sample calculatlons are included.

Report presenting an investigation of a thermal ice-prevention system for a Curtiss-Wright C-46 airplane, including the equipment for the wings, empennage, and windshield. The report is the third in a series and focuses on the revisions to the components for thermal ice prevention, the temperature- and pressure-measurement equipment installed in the airplane to determine the performance of the system, and the results of static-load structural tests of a specimen of the wing outer-panel leading edge.

Report presenting an investigation of a thermal ice-prevention system for a C-46 cargo airplane, which involved flight tests in dry-air and natural-icing conditions at two different laboratories. The purpose of the investigation was to determine the effectiveness of the C-46 airplane ice-prevention system and to continue the develop of thermal ice-prevention equipment. Results regarding the wing outer panel, wing tips, wing center panel, horizontal stabilizers, vertical fin, windshields, ice-removal tests, unprotected surfaces, and heat exchangers are provided.

Report discussing the use of two types of geared spring tabs for elevator control: ordinary (or ungeared) spring tabs and geared spring tabs. Their use in airplanes of various sizes and in comparison to conventional control systems is described.

Report presenting an investigation of an exhaust-air heat exchanger, which has been designed, constructed, and flight-tested for a C-46 cargo airplane. The primary purpose of the investigation was to provide the C-46 airplane with a satisfactory source of heated air and to continue the development of the heat exchanger as a part of thermal ice-prevention equipment. Results indicated that the required thermal output and desired air-temperature rise have been achieved and that the exchanger is suitable for use in the C-46 airplane.

Report presenting tests of two typical low-drag airfoils of 90-inch chord to determine the effects of surface projections, grooves, and sanding scratches on boundary-layer transition. Data were obtained for projections of various sizes and chordwise locations on both low-drag airfoils.

Note presenting an investigation of the problem of the buckling of parallel simply supported tension and compression members connected by equally stiff and equally spaced elastic deflection springs as an approximation to the problem of the effect of finite stiffness of ribs and tension surface on the buckling load of the compression surface of a wing. Charts relating compressive buckling load, deflectional spring stiffness, and the ratio of the flexural stiffness of the members are given for tension and compression members with various numbers of spans.

Report presenting the results of a study to determine the effect of rotation on the dynamic-stress distribution in vibrating cantilever beams. Both theoretical and experimental results are obtained by means of stroboscopic photographs and strain gauges. Both types of results indicated that the introduction of centrifugal force had no effect on the maximum dynamic-stress locations in a vibrating cantilever beam fixed at the center of rotation within the investigated speed range.

Report presenting the results of an experimental investigation of the aerodynamic characteristics of a rotating axial-flow blade grid with pressure-increasing effect. Several techniques of measurement were used, including pressure distribution measurements, pitot tubes, and hot wire wake surveys. Results regarding the lift and pressure drag of the blade sections, aerodynamic characteristics of the blade sections, profile drag, and static pressure are provided.

Note presenting selected pressure-distribution diagrams for a number of conventional and special airfoils. The conventional airfoils include the NACA 22, 44, and 230 series airfoils and Clark Y family and the special airfoils consist of circular-arc sections of several thicknesses and a number of synthetic airfoils. The pressure distributions are in most cases given for several lift coefficients including that at the ideal angle of attack.

"A method of measuring foaming volume is described and investigated to establish the critical factors in its operation. Data on foaming volumes and foam stabilities are given for a series of hydrocarbons and for a range of concentrations of aqueous ethylene-glycol solutions. It is shown that the amount of foam formed depends on the machinery of its production as well as on properties of the liquid, whereas the stability of the foam produced, within specified mechanical limitations, is primarily a function of the liquid" (p. 1).

Note presenting results of flight tests made to determine the effect of flap deflection on the lateral control characteristics of a modified Brewster F2A-2 airplane equipped with partial-span narrow-chord ailerons on the trailing edge of a full-span NACA slotted flap. The results indicated that the effectiveness of the ailerons was greatly reduced at flap deflections greater than about 20 degrees.

Theoretical analysts of lateral dynamic motion of tailless and conventional airplanes was made for fighter and heavy transport. Their reactions to a lateral gust and control power required by each for simple maneuvers were determined and compared. Both types of airplanes require almost identical aileron control power to perform a given maneuver; tailless airplane requires about 1-2 to 1-3 directional control power of conventional airplane. Tailless airplane also shows greatest displacement for a given disturbance and has least damping in oscillatory mode.

Report presenting an investigation of the effect of partial admission of the driving fluid on the performance of a representative full-admission, production-type gas turbine. Results regarding losses, full-admission performance, partial-admission performance, partial admission as a means of power control, and a comparison of partial admission with other methods of power control are provided.

"A method has been developed for evaluating from shadow or schileren photographs the pressure drag of axially symmetrical bodies at zero angle of attack or of two-dimensional bodies producing detached shock. The method consists in the determination of the flow properties along a characteristic line and the application of the momentum theorem to a stream tube around the body. The method can be applied to the determination of external drag of supersonic inlets with subsonic flow at the entrance of the inlet" (p. 1).

From Summary: "In order to facilitate the application of miscellaneous airfoil data to the problems of the helicopter designer, a discussion of a number of the problems most frequently arising is presented. A reference list of published papers on airfoil section characteristics (or their application) which experience has shown to be useful in connection with these helicopter problems is included."

Report presenting a study of experimental pressure distributions and section characteristics for several moderately thick airfoil sections were made. The pressure distributions and section force characteristics of several moderately thick airfoil sections at Mach numbers above the drag-divergence Mach numbers were analyzed.

Report presenting an analysis showing the effect of several design variables on turbine-wheel flight. Equations are developed for the calculations of weights of the disk, the rim, and the blades, and use the following variables: the blading aspect ratio and solidity, the ratio of the centrifugal stress at the blade roots to that in the disk, and the ratio of wheel diameter at the blade root to wheel diameter at the blade tip.

Report presenting an investigation to determine the effects of loading on the performance of axial-flow fan and compressor blades in a test blower. Results regarding verification of the two-dimensional design data and effects of blade roughness are provided.

"A study of the subsonic flow past an infinitely long corrugated circular cylinder is presented to show the relation between two-dimensional and axisymmetrical flow. In fact, a solution is obtained which contains as limiting cases both the Prandtl-Glauert correction for two-dimensional flow and the Göthert correction for flow past slender bodies of revolution. Included in the paper are velocity-correction formulas for a cylinder with a single bump and for a corrugated cylinder in the presence of walls" (p. 1).

Report presenting an application of the linearized supersonic flow theory to the calculation of the camber and twist required for various lift distributions on a triangular wing with leading edges behind the Mach cone. Several specific examples are used and plots of the cambered surfaces, corresponding lift distributions, and values of the theoretical drag coefficients are presented.

Report presenting the application of dimensional analysis to the computation of the main bearing of a V-type in-line aircraft engine. Two crankshafts have been considered, one designed for higher operating speed than the other. Two types of engines are considered: one for regular V-type engines and one for production V-type engines.

Note presenting a method for calculating the response and lag in pressure measuring systems subjected to steady-state sinusoidally varying pressures. The pressure system is assumed to consist of an inlet restriction, tubing length, and connected instrument volume. Results of the phase-shift determination are provided.

From Summary: "Reduction of pentaerythrityl tetrabromide in ethanol with zinc in the presence of sodium carbonate and sodium iodide was found to yield methylenecyclobutane, spiropentane, and 2-methyl-l-butene. Yields were 46 percent methylenecyclobutane, 21 percent spiropentane, and 12 percent 2-methyl-l-butene. The reduction procedure described offers a method of preparing both methylenecyclobutane and spiropentane from the same reaction in yields comparable with individual methods of synthesis previously reported."