Abstract: A pilot plant facility for recovering Pu238 and unconverted neptunium from irradiated neptunium target elements was operated for 17 months at the Savannah River Laboratory. The process required that the irradiated target elements be dissolved and the solution be processed through three anion exchange cycles for removal of undesirable fission products and cations, recovery of unconverted neptunium, and concentration of Pu238 solution. The process equipment was enclosed in three stainless steel boxes that were installed in two general-purpose cells of a ten-cell complex. The basic cells were not modified. The two cells were not separated from from the adjacent 8 cells. Containment of the high-specific-activity alpha emitters was accomplished by ventilation, development of handling techniques, use of procedures, and close Radiation Control coverage. The facility was dismantled, and the cells were decontaminated and returned to normal use. With the exception of an accidental overexposure, all personnel exposures were kept below the administrative level of 3 R/yr. None of the personnel assimilated detectable amounts of he material handled.

"The performance of the Model I electrostatic precipitator sampler in recent field and laboratory tests is described and discussed. Two of the four precipitator-bearing balloon flights during this interval reached the floating altitude of approximates 105,000 feet, and the precipitator operated efficiently on both. One sample was collected at the nominal design flowrate of approximates 100 cfm, and the second at approximates -200 cfm. Comparison of the deposition profiles of the stratospheric samples with those obtained under controlled conditions in the altitude chamber indicates that the field samples were collected with >90% efficiency. The laboratory tests also showed that the performance capability of the precipitator improves with increasing precipitator current, and with increasing altitude. One of the above balloon flights carried two Model A-I altimeters with recorder outputs. The two records were identical within plus or minus 250 feet. In addition, variations in altitude indications were consistent with the less sensitive aneroid barocoder measurements from the same flight. A revised Model A-I altimeter with a telemeterable output signal has been designed and constructed. The frequency of the signal is a function of the altitude. A preliminary design concept for a flowmeter with negligible flow resistance is described. It would utilize …

Summary: Two UO2-filled stainless steel clad fuel rods in which fission gas pressure was measured during irradiation have been subjected to post irradiation examination. Results of free gas analysis and metallographic examination are in general agreement with observed pressures reported previously. Calculated fuel surface temperatures based on extent of fuel recrystallization indicate that in a one-half inch diameter fuel rod with 0.014 inch diametral clearance operated at a maximum heat flux of 531,000 Btu/hr-ft, gap conductance increased with increasing heat flux. An analysis of void configuration indicates that pressure is more sensitive to as-fabricated void volume and changes in this volume resulting from fuel expansion than to fuel central temperature. The decreases in effective void volume with increasing fuel temperatures becomes more significant as initial void volume decreases, and excessive fission gas pressures may be developed in fuel rods operated at high fuel temperatures unless adequate expansion volume is provided in fabrication.

Technical report describing the four-rod heat flux experiments that are a part of a continuing program of study of the critical heat flux, or burnout phenomenon in order that water cooled reactors can be designed with a maximum of safety and efficiency. During heat transfer with boiling, there is a particular heat flux, for a given set of flow conditions and geometry, above which the nucleate boiling process begins to break down. This breakdown of the nucleate boiling process is known as burnout, critical heat flux, departure from nucleate boiling (DNB), and boiling crisis. The present method at General Electric of avoiding the critical heat flux conditions in the reactor is to limit the heat flux, for a given set of flow conditions, to a fraction of the critical heat flux at the same conditions in the single-rod test section of Janssen and Kervinen. Because the critical heat flux of a heater rod facing an unheated wall is lower than that of a heater rod facing another heater rod, the critical heat flux conditions of the single-rod test section, will be a conservative estimate of the critical heat flux conditions in a multirod reactor. The main purpose of these experiments …

Summary: The High Power Density Project includes a comprehensive fuel development program which has the objective of developing and demonstrating the performance of a nuclear reactor core having a high power density, long fuel life, and low fabrication cost. The fuel program is made up of two principal tasks. Task 1A consists of irradiation tests in the VBWR of Type 304 stainless steel clad, UO2 pellet type fuel rods fabricated by current commercial processes. Task 1B consists of the investigation of lower cost fabrication processes and the irradiation testing of fuel elements fabricated by these processes. Both tasks include the investigation of the feasibility and use of thin-wall stainless steel cladding as a means of improving the neutron economy and fuel cycle costs of stainless steel clad fuel. Irradiation of the Task 1A fuel assemblies in the VBWR was initiated in September, 1960. Subsequently, Task 1B fuel assemblies were inserted in the VBWR as various fabrication processes and design concepts were investigated. Fuel cladding failures have occurred in fuel rods in both Task 1A and 1B. As of this date, cladding failures have occurred in twenty-two rods of approximately 700 fuel rods which have been irradiated. Twenty of the failures …

Quarterly progress report on Accurate Nuclear Fuel Burnup Analysis project.

Technical report describing that the pressure drops along 3/4-inch, 1-inch, and 1-1/4 inch straight pipes and across three contraction-expansion inserts in a 1-inch pipe have been measured under both single- and two-phase flow conditions. Pressure was varied from 600 to 1400 psia, flow from 0.25 x 10(6) to 1.66 x 10(6) lb/hr ft, and quality from zero to 90 percent. The single-phase pipe friction factor agrees with the Moody value for smooth pipe. The two-phase friction for horizontal flow shows no size effect in the range of pipe sizes from 3/4 inch to 1-1/4 inch. The values lie below the Martinelli curve at the lower qualities (x<0.6), but at high qualities tend to be above the Martinelli curve. The single-phase loss coefficient for the three contraction-expansion inserts show very little Reynolds number effect in the range of channel Reynolds numbers from 3 x 10(4) to 5 x 10(5). The two-phase data for insert number 1 has not yet been reduced. The two-phase loss for insert numbers 2 and 3 lies generally below the loss prediction based on a homogeneous flow model. The two-phase loss for insert number 2 shows excellent agreement with the corresponding loss for the S-1 insert in …

Quarterly report describing progress on the EVESR Nuclear Superheat Fuel Development Project.

Task A: Modification and Preparation of Experimental Facility. With the exception of the insulation of modified components, the experimental facility is complete. Insulation will be completed by the end of September. the system has been charged with Refrigerant-22 and preliminary loop performance tests have been completed without the test sections.. Task B: Design and Construction of Test Sections. The stainless steel test section has been prepared complete with end flanges and pressure tap locations. Wall thickness tolerances have been ultrasonically checked. Test section inlet and discharge assemblies are being completed and the whole assembly will be ready for installation by the end of September. Glass sections from the same drawn length which will make up the final test sections have been received for pressure tests. The final coated sections and the associated inlet and discharge fittings will be ready for assembly by the end of September. The above sections were ordered after complete preliminary tests defined the properties required of these test sections. Task C: Design and Construction of Test Stand: The mechanical design and drafting of the structural components and drive system is complete. The electrical control system for the platform orientation has been constructed and two modes of …

The Heavy Water Components Test Reactor (HWCTR) was built for the Atomic Energy Commission by the Du Pont Company to satisfy a need for fuel testing in the AEC's Heavy Water Power Reactor Program. The reactor was designed to provide a realistic test environment for full size fuel candidates. The report contains sections on (1) the containment building, (2) vertical cross section of the reactor vessel, (3) core layout, (4) low power physics tests and comparison with calculations, (5) rod worths, (6) temperature coefficients, (7) flux shapes, and (8) the operating philosophy of a test reactor.

The Heavy Water Components Test Reactor (HWCTR) is a pressurized reactor, cooled and moderated with D2O, and has the capability of testing fuel assemblies under operating conditions of coolant flow, temperate, and pressure that are typical of those proposed for modern power reactors. The report contains (1) description of the four systems used for failed element detection, (2) discussion of the laboratory analyses of water samples used a as backup for the fuel failure instruments, (3) description of 3 monitors, Cyclic Air Sampling Monitor, Stack Gas Activity Monitor, Health Physics Building Monitors, (4) normal full power activity readings, (5) discussion of the experience during fuel failure.

The Heavy Water Components Test Reactor (HWCTR) is used to test prototype fuel elements for power reactors that are moderated with heavy water and fueled with natural or slightly enriched uranium. During the initial critical experiments in the HWCTR, it was observed that there were unexpected variations in nuclear reactivity. Investigations revealed that this effect was due to bubble of helium gas appearing and disappearing in the moderator. An examination of the expected operating conditions of the HWCTR and the solubility of helium in D2O showed that it was possible during normal operation for the helium content of the moderator to exceed saturation and thus for helium to appear as bubbles in the moderator. The possibility of helium bubbles appearing in the moderator because of solubility characteristics was eliminated by modifications to the process system so as to maintain the gas content of the moderator appreciably below saturation.

The Plutonium Recycle Test Reactor is a research and development tool supporting the Plutonium Recycle Program and the research activities at Hanford. The present organization directly associated with the PRTR is composed of Operating, Technical Assistance, Maintenance, and Engineering Groups. Liaison with research groups utilizing PRTR facilities is accomplished through the Technical Assistance Group. the other three groups serve the PRTR in the manner suggest by the group name. This paper limits its interest to the staffing experience of the Operating Group.

Abstract. The kangaroo rat is readily tamed and has certain characteristics that make it unique and of interest in highly specialized research programs. Studies were conducted on its ability to exist on a dried diet with only a bare minimum of water and that obtained from succulent plants. Hematological studies indicate that the kangaroo rat exhibits a different hematological distribution of cells than the mouse or rat. The lymphocyte constitutes 81.4% of the total leuokocytes. The hematocrit has a value of 46 to 48 in spite of the high degree of water conservation practiced by the animal. The response to ionizing radiation of this species does not differ from that reported for the mouse or rat. Behavior studies indicate that the digging characteristics of the kangaroo rat are similar to those of the gerbil. Furthermore, the animal shows definite psychotic tendencies under the influence of psychotomimetics like LSD-25 and psilocybin. An evaluation of the physiological responses of isolated tissues from this animal as well as its responses to anesthetics is being undertaken to evaluate its further usefulness in the laboratory.

Report issued by Oak Ridge National Laboratory that describes research and progress at the Chemical Technology Division.

From abstract: "The experimental determination of the effects of sodium ingress on high-performance oxide fuels is described. Capsule design, fabrication, irradiation, examination, and analysis are described in detail."

Report describing a portable radiation survey instrument, its design, and usage.

Montgomery and Chandrasekhar and Hulm suggested models for predicting Im and Hm of high-field superconducting solenoids. Montgomery's model for predicting the degradation effect of superconducting solenoids leads to a unique coil quenching characteristics if geometrically similar solenoids are considered. Experiments do not verify these predicted results. Chandrasekhar and Hulm's model leads to one unique coil quenching characteristic for all solenoids with identical wire type and turn distance; coils with identical load factor should display identical values im and Hm. An analysis of the surface currents in an ideal superconducting infinitely long solenoid demonstrated possible forms of shielding currents. Experiments with Pb coils with and without NbZr and compensation agree with results expected from this analysis, but contradict Chandrasekhar and Hulm's model. Measurements of individual turn resistances show behavior of a soft superconductor solenoid in the intermediate state.

The radiation chemistry of ammonia, pure or with various additives, was studied by Co60 gamma radiation. The kinetics of aniline formation by the irradiation of homogeneous benzene-ammonia mixtures was determined together with the kinetics of hydrazine formation in the case of pure ammonia. The effects of dose, intensity, temperature, and specific additives were determined.