The purpose of this engineering note is to provide the necessary information to setup, program, and network the Electronic Systems USA Heat Pump Controller with the LON network card and Intellution Fix32 to operate properly within the HVAC system at D-Zero. The heat pump controllers are used for local temperature control of the office environments on the fifth and six floors of D-Zero. Heat pump units 1-6 are located in the ceiling of the sixth floor. Heat pump units 7-12 are found in the fifth floor ceiling. Heat pump unit 13 is in the Southeast corner of the fifth floor. Prior to installation the heat pump controller must be properly prepared to operate correctly in the HVAC system. Each heat pump unit must contain firmware (software) version 1.31 to operate properly on the network. Controllers with version 1.30 will not be able to communicate over the LON network. The manufacturer can only update the firmware version. Before installation a series of heat pump setpoints must be manually set using the Intelligent Stat. Connect the Intelligent Stat via the serial cable or wired connection.

EBSD in the SEM has been developed into a tool that can provide identification of unknown crystalline phases with a spatial resolution that is better than one micrometer. This technique has been applied to a wide range of materials. Use of the HOLZ rings in the EBSD patterns has enabled the reduced unit cell to be determined from unidexed EBSD patterns. This paper introduces EBSD for phase identification and illustrates the technique with examples from metal joining and particle analysis. Reduced unit cell determination from EBSD patterns is then discussed.

Progress made and problems encountered so far is discussed with reference to the Statement of Work which was submitted as part of the grant application. This work plan breaks down the project into fourteen numbered tasks grouped into three phases: Development of Improved Sensor Materials (Phase 1), Laboratory Testing of Improved Prototype on 15 kV Switchgear (Phase 2),and Field Testing of Beta Prototype and Start of Commercialization (Phase 3).

As directed by a written development plan (CRWMS M&O 1999a), a conceptual model for steel and corrosion products in the engineered barrier system (EBS) is to be developed. The purpose of this conceptual model is to assist Performance Assessment Operations (PAO) and its Engineered Barrier Performance Department in modeling the geochemical environment within a repository drift, thus allowing PAO to provide a more detailed and complete in-drift geochemical model abstraction and to answer the key technical issues (KTI) raised in the NRC Issue Resolution Status Report (IRSR) for the Evolution of the Near-Field Environment (NFE) Revision 2 (NRC 1999). This document provides the conceptual framework for the in-drift corrosion products sub-model to be used in subsequent PAO analyses including the EBS physical and chemical model abstraction effort. This model has been developed to serve as a basis for the in-drift geochemical analyses performed by PAO. However, the concepts discussed within this report may also apply to some near and far-field geochemical processes and may have conceptual application within the unsaturated zone (UZ) and saturated zone (SZ) transport modeling efforts.

This Institutional Plan describes what Argonne management regards as the optimal future development of Laboratory activities. The document outlines the development of both research programs and support operations in the context of the nation's R and D priorities, the missions of the Department of Energy (DOE) and Argonne, and expected resource constraints. The product of many discussions between DOE and Argonne program managers, the Draft Institutional Plan is provided to the Department before Argonne's On-Site Review. Issuance of the final Institutional Plan in the fall, after further comment and discussion, marks the culmination of the Laboratory's annual planning cycle. The final Plan also reflects programmatic priorities developed during Argonne's summer strategic planning process and the allocation of Laboratory Directed Research and Development funds.

The authors have used ion channeling to examine the lattice configuration of deuterium in Mg doped GaN grown by MOCVD. The deuterium is introduced both by exposure to deuterium gas and to ECR plasmas. A density functional approach including lattice relaxation, was used to calculate total energies for various locations and charge states of hydrogen in the wurtzite Mg doped GaN lattice. Computer simulations of channeling yields were used to compare results of channeling measurements with calculated yields for various predicted deuterium lattice configurations.

The corrosion behavior of a titanate ceramic was investigated with the aim of describing the rate-controlling process or processes. These titanate ceramics are similar to SYNROC and are proposed as immobilization materials for surplus Pu. The corrosion behavior was described with results from MCC-I and PCT-B static dissolution tests. Three important observations were made: (a) Ca is released at a constant rate [6x10{sup -5}g/(m{sup 2} day)] in PCT-B tests for up to two years, (b) all of the test leachates are oversaturated with respect to rutile and anatase, and (c) the release rates for Pu and Gd increase with time (up to two years) in PCT-B tests. The first observation suggests that the ceramics continue to corrode at a low rate for at least 2 years in PCT-B tests. The second observation shows that the rate of the corrosion reaction is not affected by the concentration of Ti in solution, suggesting that the approach to saturation with respect to either rutile or anatase is not a rate-limiting process. The third observation shows that the rate of Pu and Gd release increases with time in these tests. While this observation cannot be fully explained at this point, two possible explanations, alteration …

None

The strength and modulus of amorphous diamond, a new material for surface micromachined MEMS and sensors, was tested in uniaxial tension by pulling laterally with a flat tipped diamond in a nanoindenter. Several sample designs were attempted. Of those, only the single layer specimen with a 1 by 2 {micro}m gage cross section and a fixed end rigidly attached to the substrate was successful. Tensile load was calculated by resolving the measured lateral and normal forces into the applied tensile force and frictional losses. Displacement was corrected for machine compliance using the differential stiffness method. Post-mortem examination of the samples was performed to document the failure mode. The load-displacement data from those samples that failed in the gage section was converted to stress-strain curves using carefully measured gage cross section dimensions. Mean fracture strength was found to be 8.5 {+-} 1.4 GPa and the modulus was 831 {+-} 94 GPa. Tensile results are compared to hardness and modulus measurements made using a nanoindenter.

The behavior of MEMS devices is limited by the strength of critical features such as thin ligaments, oxide cuts joining layers, pin joints and hinges. Devices fabricated at Sandia's Microelectronic Development Laboratory have been successfully tested to investigate these features. A series of measurements were performed on samples with gage lengths of 15 to 1000 microns, using conventional and tungsten coated samples as well as samples that include the critical features of standard components in the test section. Specimens have a freely moving pin joint on one end that anchors the sample to the silicon die to allow rotation to reduce effects of bending. Each sample is loaded in uniaxial tension by pulling laterally with a flat tipped diamond in a computer-controlled Nanoindenter. Load is calculated by resolving the measured lateral and normal forces into the applied tensile force and frictional losses. The specimen cross section and gage length dimensions were verified by measuring against a standard in the SEM. Multiple tests can be programmed at one time and performed without operator assistance allowing the collection of significant populations of data.

Light trucks' share of the US light vehicle market rose from 20% in 1980 to 41% in 1996. By 1996, annual energy consumption for light trucks was 6.0 x 10{sup 15} Btu (quadrillion Btu, or quad), compared with 7.9 quad for cars. Gasoline engines, used in almost 99% of light trucks, do not meet the Corporate Average Fuel Economy (CAFE) standards. These engines have poor fuel economy, many getting only 10--12 miles per gallon. Diesel engines, despite their much better fuel economy, had not been preferred by US light truck manufacturers because of problems with high NO{sub x} and particulate emissions. The US Department of Energy, Office of Heavy Vehicle Technologies, has funded research projects at several leading engine makers to develop a new low-emission, high-efficiency advanced diesel engine, first for large trucks, then for light trucks. Recent advances in diesel engine technology may overcome the NO{sub x} and particulate problems. Two plausible alternative clean diesel (CD) engine market penetration trajectories were developed, representing an optimistic case (High Case) and an industry response to meet the CAFE standards (CAFE Case). However, leadership in the technology to produce a successful small, advanced diesel engine for light trucks is an open issue …

Produced water management can be a significant expense for oil and gas operators. This paper summarizes a study of the technical, economic, and regulatory feasibility of a relatively new technology, downhole oil/water separators (DOWS), to reduce the volume of water pumped to the surface. The study was funded by the US Department of Energy and conducted by Argonne National Laboratory, CH2M Hill, and the Nebraska Oil and Gas Conservation Commission. DOWS are devices that separate oil and gas from produced water at the bottom of the well and reinject some of the produced water into another formation or another horizon within the same formation, while the oil and gas are pumped to the surface. Since much of the produced water is not pumped to the surface, treated, and pumped from the surface back into a deep formation, the cost of handling produced water is greatly reduced. The oil production rate has increased for more than half of the DOWS installations to date.

The authors investigated the behavior of speckle contrast and size under various experimental conditions using 1.82 keV x-rays. In this paper, they report the comparison of two different setups for x-ray speckle experiments: one employing a focusing zone plate and one in which a pinhole selects the size of the coherent x-ray beam. They found a strong dependence of the speckle contrast and size on the type of setup. In general, the pinhole setup results in higher contrast but smaller speckle size. On the other hand the zone plate setup allows one to target much smaller areas of interest in the sample, down to submicron dimensions, and also to adjust the speckle size. The authors anticipate that these results will be useful in future time-correlation spectroscopy experiments.

This semi-annual technical progress report describes work performed under DOE Grant No. DE-FG22-96PC96224 during the period March 24, 1999 to September 23, 1999 which covers the last (sixth) six months of the project. During this reporting period, extraction of devolatilization time-scales and temperature data at these time-scales analyzing the high-speed films taken during the experiments was complete. Also a new thermodynamic model was developed to predict the heat transfer behavior for coal particles subjected to a range of heating rates using one approach based on the analogy of polymers. Sensitivity analyses of this model suggest that bituminous coal particles behave like polymers during rapid heating on the order of 10{sup 4}-10{sup 7} K/s. At these heating rates during the early stages within the first few milliseconds of heating time, the vibrational part of the heat capacity of the coal molecules appears to be still frozen but during the transition from heat-up to devolatization, the heat capacity appears to attain a sudden jump in its value as in the case of polymers. There are few data available in the coal literature for 10{sup 2}-10{sup 3} K/s obtained by UTRC in their previous studies. These data were obtained for a longer heating …

Beamline-control and data-acquisition software based on EPICS (a tool kit for building distributed control systems) has been running on many Advanced Photon Source beamlines for several years. EPICS itself, the collaborative software-development effort surrounding it, and EPICS-based beamline software have been described previously in general terms. This talk will review and update that material, focusing on the role EPICS core software plays in beamline applications and on the effects of a few defining characteristics of EPICS on the beamline software we have developed with it.

A hard x-ray scanning microprobe based on zone plate optics and undulator radiation, in the energy region from 6 to 20 keV, has reached a focal spot size (FWHM) of 0.15 {micro}m (v) x 0.6 {micro}m (h), and a photon flux of 4 x 10{sup 9} photons/sec/0.01%BW. Using a slit 44 meters upstream to create a virtual source, a circular beam spot of 0.15 {micro}m in diameter can be obtained with a photon flux of one order of magnitude less. During fluorescence mapping of trace elements in a single human ovarian cell, the microprobe exhibited an imaging sensitivity for Pt (L{sub a} line) of 80 attograms/{micro}m{sup 2} for a count rate of 10 counts per second. The x-ray microprobe has been used to map crystallographic strain and multiquantum well thickness in micro-optoelectronic devices produced with the selective area growth technique.

Exciting new applications of high-resolution x-ray imaging have emerged recently due to major advances in high-brilliance synchrotrons sources and high-performance zone plate optics. Imaging with submicron resolution is now routine with hard x-rays: the authors have demonstrated 150 run in the 6--10 keV range with x-ray microscopes at the Advanced Photon Source (APS), a third-generation synchrotrons radiation facility. This has fueled interest in using x-ray imaging in applications ranging from the biomedical, environmental, and materials science fields to the microelectronics industry. One important application they have pursued at the APS is a study of the microbiology of bacteria and their associated extracellular material (biofilms) using fluorescence microanalysis. No microscopy techniques were previously available with sufficient resolution to study live bacteria ({approx}1 {micro}m x 4 {micro}m in size) and biofilms in their natural hydrated state with better than part-per-million elemental sensitivity and the capability of determining g chemical speciation. In vivo x-ray imaging minimizes artifacts due to sample fixation, drying, and staining. This provides key insights into the transport of metal contaminants by bacteria in the environment and potential new designs for remediation and sequestration strategies.

The radiation level at High Energy Particle Accelerators (HEPA) is relatively high. Any active component which should be close to the accelerator has to be radiation hard. Since High Temperature Superconductors (HTS) have a great potential to be used in HEPAs (e.g., in superconducting magnets, current leads, RF cavities), it is important to understand the radiation hardness of these materials. A radiation test of HTS wire (Bi-2223) was performed at Fermilab. The HTS sample was irradiated with 8 GeV protons and the relative I{sub c} was measured during the irradiation. The total radiation dose was 10 Mrad, and no I{sub c} degradation was observed.

Hydrogen can be absorbed in large quantities by 100 {angstrom} thin Nb layers embedded in epitaxial W/Nb and polycrystalline Fe/Nb multilayers. The solubility and the hydrogen-induced structural changes of the host lattice are explored in-situ by small-angle neutron/X-ray reflectometry and high-angle diffraction. These measurements reveal for both systems that the relative out-of-plane expansion of the Nb layers is considerably larger than the relative increase of the Nb interplanar spacing indicating two distinctly different mechanisms of hydrogen absorption. In Fe/Nb multilayers, hydrogen expands the Nb interplanar spacing in a continuous way as function of the external pressure. In contrast, the Nb lattice expansion is discontinuous in epitaxial W/Nb multilayers: A jump in the Nb(002) Bragg reflection position occurs at a critical hydrogen pressure of 1 mbar. In-situ EXAFS spectroscopy also exhibits an irreversible expansion of the Nb lattice in the film plane for p{sub H{sub 2}}> 1 mbar. This can be regarded as a structural phase transition from an exclusively out-of-plane to a three-dimensionally expanded state at low and high hydrogen pressures, respectively.

The primary objective of this project is to enhance domestic petroleum production by field demonstration and technology transfer of an advanced- oil-recovery technology in the Paradox basin, southeastern Utah. If this project can demonstrate technical and economic feasibility, the technique can be applied to approximately 100 additional small fields in the Paradox basin alone, and result in increased recovery of 150 to 200 million barrels (23,850,000-31,800,000 m3) of oil. This project is designed to characterize five shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation and choose the best candidate for a pilot demonstration project for either a waterflood or carbon-dioxide-(CO2-) miscible flood project. The field demonstration, monitoring of field performance, and associated validation activities will take place within the Navajo Nation, San Juan County, Utah.

The reaction between H{sub 2} and O{sub 2} has been studied in a reflected shock tube apparatus between 1662--2097 K. O-atom atomic resonance absorption spectrometry (ARAS) was used to observe absolute [O]{sub t} under conditions of low [H{sub 2}]{sub 0} so that most secondary reactions were negligible. Hence, the observed [O]{sub t}, was the direct result of the rate controlling reaction between H{sub 2} and O{sub 2}. Three different reactions were considered, but experimental and ab initio theoretical results both indicated that the process, H{sub 2} + O{sub 2} {yields} H + HO{sub 2}, is the only possible reaction. After rapid HO{sub 2} dissociation, O-atoms are then instantaneously produced by H + O{sub 2} {yields} O + OH. Using the ab initio result, conventional transition state theoretical calculations (CTST) with tunneling corrections give the expression: k = 1.228 x 10{sup {minus}18} T{sup 2.4328} exp({minus}26926 K/T) cm{sup 3} molecule{sup {minus}1} s{sup {minus}1}, applicable between 400 and 2,300 K. This theoretical result agrees with the present experimental determinations and those at lower temperature, derived from earlier work on the reverse reaction.

The leading environmental problem facing coastal Louisiana regions is the loss of wetlands. Oil and gas exploration and production activities have contributed to wetland damage through erosion at numerous sites where canals have been cut through the marsh to access drilling sites. An independent oil and gas producer, working with Southeastern Louisiana University and two oil field service companies, developed a process to stabilize drill cuttings so that they could be used as a substrate to grow wetlands vegetation. The U.S. Department of Energy (DOE) funded a project under which the process would be validated through laboratory studies and field demonstrations. The laboratory studies demonstrated that treated drill cuttings support the growth of wetlands vegetation. However, neither the Army Corps of Engineers (COE) nor the U.S. Environmental Protection Agency (EPA) would grant regulatory approval for afield trial of the process. Argonne National Laboratory was asked to join the project team to try to find alternative mechanisms for gaining regulatory approval. Argonne worked with EPA's Office of Reinvention and learned that EPA's Project XL would be the only regulatory program under which the proposed field trial could be done. One of the main criteria for an acceptable Project XL proposal is …

This document provides a summary of the systematic process used by the SNF Project to characterize K-Basin spent fuel, and to develop and apply the appropriate conservative safety margins to the resulting parameters for technical designs and safety analyses.

The Materials Research Institute (MRI) is the newest of the University/LLNL Institutes and began operating in March 1997. The MRI is one of five Institutes reporting to the LLNL University Relations Program (URP), all of which have as their primary goal to facilitate university interactions at LLNL. This report covers the period from the opening of the MRI through the end of FY98 (September 30, 1998). The purpose of this report is to emphasize both the science that has been accomplished, as well as the LLNL and university people who were involved. The MRI is concentrating on projects, which highlight and utilize the Laboratory's unique facilities and expertise. Our goal is to enable the best university research to enhance Laboratory programs in the area of cutting-edge materials science. The MRI is focusing on three primary areas of materials research: Biomaterials (organic/inorganic interfaces, biomemetic processes, materials with improved biological response, DNA materials science); Electro/Optical Materials (laser materials and nonlinear optical materials, semiconductor devices, nanostructured materials); and Metals/Organics (equation of state of metals, synthesis of unique materials, high explosives/polymers). In particular we are supporting projects that will enable the MRI to begin to make a distinctive name for itself within the scientific …