The sphere-cylinder method of using nuclear magnetic resonance (NMR) to measure the magnetic susceptibility of diamagnetic and paramagnetic materials has been generalized to the disk-cylinder method. A two-fold increase in sensitivity was obtained. Accuracies of 0.1% of the diamagnetism of water should be readily obtainable.

This detailed report on Lawrence Livermore Laboratory's control program to minimize beryllium levels in Laboratory workplaces includes an outline of beryllium surface, soil, and air levels and an 11-y summary of sampling results from two high-use, high-explosive test firing bunkers. These sampling data and other studies demonstrate that the beryllium control program is funcioning effectively.

The removal of CO/sub 2/ from air in a calcium hydroxide slurry-agitated reactor was investigated to aid the design of such vessels. Gas-liquid interfacial areas were calculated using theoretical rate expression and experimental data at specific operating conditions. A correlation for interfacial areas was then determined as a function of impeller speed, impeller diameter, gas flow rate, and concentration of the slurry. Decontamination factors were also determined.

This study was conducted to identify processes that are most applicable for control of H/sub 2/S from geothermal sources. Both vapor-dominated and liquid-dominated sources were considered within the electric power generation category. The source characteristics, H/sub 2/S control requirements, and applicable technologies are discussed for the two geothermal sources. An evaluation of the applicable control technology indicates that there are three major approaches for H/sub 2/S removal. These are (a) upstream cleaning (ahead of the power plant), (b) removal of H/sub 2/S from condenser vent emissions, and (c) H/sub 2/S removal from cooling water, including condensate. The most promising processes for these emission points, based on current information, are as follows: the EIC process for upstream cleaning of liquid-dominated sources. For condenser vent emissions, the Stretford process appears to be most applicable; for cooling tower emissions, the iron catalyst process, followed by the H/sub 2/O/sub 2/ process, seems most appropriate.

A New Waste Calcining Facility is being built at the Idaho Chemical Processing Plant to replace the existing Waste Calcining Facility which was built to demonstrate fluidized-bed solidification of highly radioactive liquid wastes. The new facility is being designed to provide a higher waste throughput, more corrosion resistant materials of construction, more effective cleanup of effluent streams, and extensive remote maintenance and equipment replacement capability. The facility will also contain extensive decontamination capability should contact maintenance become necessary. The facility is presently in construction and is scheduled for hot operation in 1980.

None

Most of the Dilute Chemical Decontamination Program effort was expended on the VNC test loop simulation of a BWR decontamination. The various tasks in the Alternate Water Chemistry Program are reported on: dose rate, offgas system, leakage monitoring, materials, condensate treatment, additives, etc. (DLC)

As indicated by tests on several cameras, the dynamic range of the Lawrence Livermore Laboratory streak-camera system appears to be about two orders of magnitude greater than those reported for other systems for 10- to 200-ps pulses. The lack of a fine mesh grid in the RCA streak tube used in these cameras probably contributes to a lower system dynamic noise and therefore raises the dynamic range. A developmental tube with a mesh grid was tested and supports this conjecture. Order-of-magnitude variations in input slit width do not affect the spot size on the phosphor or the dynamic range of the RCA tube.

Preliminary studies involving vibrational energy dispersion in propynal have shown that collisionless R ..-->.. R relaxation times are approximately 3 ..mu..sec below 2000 cm/sup -1/. In the same energy regime, collisionless intramolecular V ..-->.. V appears to be much longer, approximately 40 ..mu..sec, whereas V ..-->.. T is very long (approximately msec) as expected. At higher levels of vibrational excitation (>3000 cm/sup -1/), where the density of vibrational levels is much greater, it is expected that the internal energy transfer rates will become much faster. The high and low pressure study of methanol have confirmed the origin of characteristic flame components (OH, CH, and C/sub 2/) as well as the initial combustion processes as a function of pressure. The long sought collisional mechanism for C/sub 2/ formation in hydrocarbon systems probably occurs via ..pi..2CH ..-->.. C/sub 2/ + H/sub 2/ as observed in the study of CH/sub 3/OH, CH/sub 3/CN, C/sub 2/H/sub 4/, and c-C/sub 3/H/sub 6/. In the IR photolysis of C/sub 2/H/sub 4/, C/sub 2/ is principally formed at collisionless pressures from a single C/sub 2/H/sub 4/ molecule, whereas its principal formation at collisional pressures is initiated by C = C scission. The low pressure study of CH/sub …

The stability of a liquid-lithium jet flow is of importance in a laser fusion reactor design. In this report we analyze and discuss jet stability with respect to fluid dynamics, delineating physical factors that may affect the jet breakup and performing some simple calculations to determine quantitatively the relative influences of various parameters. We define areas of uncertainty and recommend possible experimental verification, theoretical analysis, or both.

A unique pure reaction turbine, for geothermal applications, has been developed. This radial outflow reaction turbine (RORT) is designed specifically to produce power from the expansion of saturated or compressed liquid at temperatures of less than 180/sup 0/C. In the tests reported here the highest efficiency measured was 32.7%, clearly below the peak efficiency for this small machine. Extrapolations to larger machines indicate that an efficiency near 50% is a credible goal, an attractive performance as either a Total Flow expander for liquid or in conjunction with conventional flashed steam systems. A rough cost estimate indicates that a 7.5 MW RORT would cost somewhere between 0.5 M$ and 1.5 M$, and could add about 15% increase in the power output of a conventional 50 MW plant. This means that for less than a 3% increase in capital cost the bus bar energy cost can be reduced by about 10%. Another important result is that the RORT is uniquely suited for conversion of the thermal and pressure energy components in the geopressured resources. The development and proof of feasibility of efficient liquid expanders broadens the opportunities for economic power production from lower temperature geothermal resources, and possibly utilization of waste heat …

Efforts devoted to searches for short-lived nuclides in the debris from large thermonuclear explosions are reviewed along with reactor production of Es and Fm. Results of underground tests are discussed along with odd-even yield variations, and future directions for heavy-element synthesis. (JRD)

The plasma closure of spatial filter pinholes is a critical parameter in the performance of high energy glass laser systems. Using 50 to 100 J, 300 psec FWHM laser pulses on the Janus laser, an investigation has been made on closure effects in 300 ..mu..m to 500 ..mu..m diameter pinholes of various materials and thicknesses. Calorimetry measurements have yielded data on pinhole transmission and intensity loading on the periphery of the pinhole. Ultrafast streak photography measurements indicate effective closure velocities of 2 x 10/sup 7/ cm/sec to 5 x 10/sup 7/ cm/sec. Scattered light measurements have shown the transmission loss through a typical spatial filter configuration to be primarily refractive in nature.

None

A fluidized-bed incineration facility has been designed for installation at the Rocky Flats Plant to develop and demonstrate the process for the combustion of transuranic waste. The unit capacity will be about 82 kg/hr of combustible waste. The combustion process will utilize in situ neutralization of acid gases generated in the process. The equipment design is based on data generated on a pilot scale unit, and represents a scale-up factor of nine. Building modifications are complete and equipment installation has begun.

Progress in monitoring the Suncatcher solar home is reviewed. The following are included: equipment purchase and preparations, sensor installation, house comfort monitoring, experiments and intensive monitoring, solar hot water heater tests, infrared radiation tests, and gas and electric use. Data are presented. (MHR)

This specification defines the design, analysis, fabrication, testing, shipping, and quality requirements of the Insulation System for the Clinch River Breeder Reactor Plant (CRBRP), near Oak Ridge, Tennessee. The Insulation System includes all supports, convection barriers, jacketing, insulation, penetrations, fasteners, or other insulation support material or devices required to insulate the piping and equipment cryogenic and other special applications excluded. Site storage, handling and installation of the Insulation System are under the cognizance of the Purchaser.

This document provides information on the development, qualification and acceptance verification of Colt, Inc. commercial solar heating and hot water systems and components. The verification includes the performances, the efficiencies and the various methods used, such as similarity, analysis, inspection, test, etc., that are applicable to satisfying the verification requirements. Colt, Incorporated of Southern California has developed two commercial solar heating and hot water systems. The systems have been installed at Yosemite National Park, California, and Pueblo, Colorado. The systems consist of the following subsystems: collector, storage, transport, hot water, auxiliary energy, and controls.

The development of a high-frequency electronic (Stevens) ballast for fluorescent lamps is described. It is claimed that use of this ballast could reduce use energy consumption by 1.2 to 2.5 percent. The Stevens ballast has a basic efficiency of 29 percent when used with conventional lamps. With the more efficient lamps, the efficiency increases drastically. The conventional ballast and lamp has an efficiacy of approximately 60 to 63 lumens per watt (LPW). With the Stevens ballast the efficiacy raises to between 75 and 80 lumens per watt. When the Stevens ballast is utilized with the newer high efficiency lamps the efficiacy increases to 90 to 95 lumens per watt or a full 51 percent improvement over conventional coil and core ballasts and 25 percent over the best high efficiency premium coil and core ballasts. In addition to its energy savings capabilities, this high frequency fluorescent lamp ballast has the advantages that it is a true retrofit device that is directly interchangeable with the conventional coil core ballast, and it is dimmable over a wide and continuous range. (LCLC)

Performance models for a two-phase turbine were developed to verify the understanding of the loss mechanisms and to extrapolate from the single-nozzle test condition to a full-admission turbine. The numerical models for predicting the performance of the nozzle and the combined nozzle and rotor are described. Results from two-phase, static cascade tests and disk-friction and windage experiments are used to calibrate the performance model(s). Model predictions are compared with single-nozzle prototype-turbine test results, and extrapolations are made to a full-admission design. The modeling also provides predictions of performance for turbines with various blade geometries, inlet conditions, and droplet sizes. Thus the modeling provides insight into design improvements.

A modified wire drawing die for spatial filtering techniques is described. It was designed for use in high power laser systems. The diamond aperture is capable of enduring high intensity laser frequency without damaging the laser beam profile. The diamond is mounted at the beam focus in a vacuum of 1 x 10/sup -5/ Torr. The vacuum prevents plasma forming at the diamond aperture, thus enabling the beam to pass through without damaging the holder or aperture. The spatial filters are fitted with a manipulator that has three electronic stepping motors, can position the aperture in three orthogonal directions, and is capable of 3.2 ..mu..m resolution. Shiva laser system is using 105 diamond apertures for shaping the High Energy Laser Beam.

Methods of integrating data from the Near-Surface Test Facility into the overall Waste Isolation Program are examined. Discussions are presented dealing primarily with the application of numerical models to the design of a waste repository. The various types of models currently available are discussed with reference to design in basalt and the breakdown of the problem of repository design is summarized. It is shown that the most efficient method for analyzing repository design is to break the problem down into several problems which are based on physical scale. These include the area directly surrounding a single waste canister (the very near field), the area including many canisters and canister emplacement rooms (the near field), and the area including the entire repository and the rock mass to the free surface (the far field). The methods by which numerical models are used for design are discussed. Flow charts are used to show the basic input data required, the calculational processes used, and the preliminary criteria for judgment of suitable repository performance. It is shown that the ultimate design of the allowable gross thermal loading density, and, thus, the layout of the underground workings is highly dependent upon the rock mass properties supplied …

Results of isobaric expansion measurements for platinum are presented, including simultaneous values for enthalpy, specific volume, temperature and electrical resistivity in tabular form as well as numerical fits up to 7500 K. The specific heat for the liquid is C/sub p/ = 5.85 +- 0.30 R and is essentially constant up to 7500 K. The bulk thermal expansion coefficient increases from approx. 7.5 x 10/sup -5/K/sup -1/ at melt to approx. 1.03 x 10/sup -4/K/sup -1/ at 7500 K. The heat of fusion observed is ..delta..h = 0.14 +- 0.03 MJ/kg and the melting point slope with pressure is estimated to be dT/sub m//dp =31 +- 10 K/GPa. The estimated critical parameters are T/sub c/ = 9285 K, P/sub c/ = 0.9492 GPa, v/sub c/ = 2.120 x 10/sup -4/ m/sup 3//kg, and z/sub c/ = 0.5085. Preliminary results of a new sound velocity technique are discussed for lead. This technique will allow determination of specific heat c/sub v/, isothermal compressibility K/sub T/ and the constant temperature volume derivatives of entropy and internal energy, as well as the Gruneisen parameter ..gamma../sub G/.

In order to obtain access to a computer from ordinary NDT instruments, a special interface was made which acts as the buffer between the computer, and the real world. The special purpose interface, which was designed and built by Group M-1 of the Los Alamos Scientific Laboratory is described. This interface was primarily built for use with various ultrasonic equipment, but is actually a general purpose system that can perform data acquisition and control for other tests.