Report discussing an analysis of the operating characteristics of a full-floating journal bearing, a bearing in which a floating sleeve is located between the journal and bearing surfaces, is presented together with charts from which the performance of such bearings may be predicted.

Solutions of the Hugoniot shock equations and Meyer expansion equations are plotted in such a manner as to permit the pressure distribution, the local Mach number, and the angles of shock waves on arbitrary sharp-nose airfoils at supersonic speeds to be obtained directly. (author).

Column and plate compressive strengths of extruded 0-1HTA magnesium alloy were determined both within and beyond the elastic range from tests of flat end H-section columns and from local instability tests of H-, Z-, and channel section columns. These tests are part of an extensive research investigation to provide data on the structural strength of various aircraft materials. The results are presented in the form of curves and charts that are suitable for use in the design and analysis of aircraft structures.

"This paper contains a tabulation of functions of the Mach number which are frequently used in high-speed aerodynamics. The tables extend from M = 0 to M = 10.0 in increments of 0.01 and are based on the assumption that air is a perfect gas having a specific heat ratio of 1.400" (p. 1).

A method is presented for the calculation of elastic stresses in symmetrical disks typical of those of a high-temperature gas turbine. The method is essentially a finite-difference solution of the equilibrium and compatibility equations for elastic stresses in a symmetrical disk. Account can be taken of point-to-point variations in disk thickness, in temperature, in elastic modulus, in coefficient of thermal expansion, in material density, and in Poisson's ratio. No numerical integration or trial-and-error procedures are involved and the computations can be performed in rapid and routine fashion by nontechnical computers with little engineering supervision. Checks on problems for which exact mathematical solutions are known indicate that the method yields results of high accuracy. Illustrative examples are presented to show the manner of treating solid disks, disks with central holes, and disks constructed either of a single material or two or more welded materials. The effect of shrink fitting is taken into account by a very simple device.

Results are presented of tests to determine the effect of brake forming in various tempers on the strength of Alclad 75S-T aluminum alloy sheet in the direction parallel to the brake. The tensile and compressive strengths of Alclad 75S-T sheet, formed in the O and W tempers, were either increased or little affected compared with those of similarly treated unformed material. When Alclad 75S-T sheet 'as received' was formed, however, the tensile yield stress was reduced about 7 percent for the with-grain direction and 1 percent for the cross-grain direction, whereas the tensile ultimate and compressive yield stresses were increased somewhat. The elongation was always slightly reduced as a result of forming.

From Summary: "Strength tests were made of a number of 24S-T and Alclad 75S-T aluminum alloy shear webs to determine the effect of rivet or bolt holes on the shear strength. Data were obtained for webs which approached a condition of pure shear stress as well as for webs with well-developed diagonal tension. The rivet factor (pitch minus diameter), divided by pitch, was varied from approximately 0.81 to 0.62. These tests indicated that the shear stresses on the gross section were nearly constant for all values of the rivet factor investigated if the other properties of the web were not changed."

"Four methods of boundary-layer control were tried during an investigation to improve the flow in the impeller passages of a V-1710-93 engine-stage supercharger. The boundary layer along the impeller front shroud was removed by suction. In one method the removal was accomplished by recirculation of the air to the impeller inlet; in another method, by external removal. In the other methods, slots were cut through the impeller-blade faces first at 30 percent and then at 30 and 70 percent of the mean-flow-path length measured from leading edges of the rotating inlet guide vanes to introduce air from the high-pressure side of the blades into the region where stagnation and separation were suspected" (p. 1).

Tables I and II of this report summarize the gust and draft velocity data for thunderstorm flights 31, 32, and 33 of September 5, 1946, September 6, 1946, and September 10, 1946, respectively. These data were evaluated from records of NACA instruments installed in P-61C airplanes and are of the type presented for previous flights. Table III summarizes the readings of a milliammeter which was used in conjunction with other equipment to indicate ambient air temperature during thunderstorm surveys. These data were read from motion-picture records of the instrument and include all cases in which variations in the instrument indications were noted for the present flights.

"Results are presented of a flight investigation conducted on a fighter-type airplane to determine the factors which affect the loads and load distributions on the vertical tail surfaces in maneuvers. An analysis is made of the data obtained in steady flight, rudder kicks, and fishtail maneuvers. For the rudder kicks, the significant loads were the "deflection load" resulting from an abrupt control deflection and the "dynamic load" consisting of a load corresponding to the new static equilibrium condition for the rudder deflected plus a load due to a transient overshoot" (p. 1).

"Free-spinning-tunnel tests have been made on a 1/27-scale model of the Douglas XF3D-1 airplane to confirm a preliminary evaluation made of the airplane spin and recovery characteristics and previously reported. Recovery characteristics were satisfactory for erect and inverted spins when the model was in the clean condition. When the slow-down brakes were open, recoveries were slow. The pedal force necessary to reverse the airplane rudder during a spin will be within the physical capabilities of the pilot" (p. 1).

"A frequency-response method for determining the critical control-gearing and hunting oscillations of airplanes with automatic pilots is presented. The method is graphical and has several advantages over the standard numerical procedure based on Routh's discriminant. The chief advantage of the method is that direct use can be made of the measured response characteristics of the automatic pilot. This feature is especially useful in determining the existence, amplitude, and frequency of the hunting oscillations that may be present when the automatic pilot has nonlinear dynamic characteristics" (p. 1).

The mutual influences of compression shocks and friction boundary layers were investigated by means of high speed wind tunnels.Schlieren optics provided a clear picture of the flow phenomena and were used for determining the location of the compression shocks, measurement of shock angles, and also for Mach angles. Pressure measurement and humidity measurements were also taken into consideration.Results along with a mathematical model are described.

"An exact solution of the problem of designing an airfoil with a prescribed velocity distribution on the suction surface in a given uniform flow of an incompressible perfect fluid is obtained by replacing the boundary of the airfoil by vortices. By this device, a method of solution is developed that is applicable both to isolated airfoils and to airfoils in cascade. The conformal transformation of the designed airfoil into a circle can then be obtained and the velocity distribution at any angle of attack computed. Numerical illustrations of the method are given for the airfoil in cascade" (p. 1).

Report presenting an investigation of the lateral-control characteristics of several spoiler arrangements located near the wing trailing edge in flight. In all cases, the control response was satisfactory and the variation of rolling effectiveness with control deflections was smooth and nearly linear. Results regarding response characteristics, rolling effectiveness, control-force and hinge-moment characteristics, yawing characteristics, effects of altitude, characteristics near the stall, and characteristics in inverted flight are provided.

"The XF-12 airplane is a high performance, photo-reconnaissance aircraft designed by the Republic Aviation Corporation for Army Air Forces. A series of tests of a 1/8.33-scale powered model was conducted in the Langley 9-foot pressure tunnel to obtain information relative to the aerodynamic design of the airplane. This report presents the results of tests to determine the static longitudinal stability and stalling characteristics of the model" (p. 1).

"An approximation method for three-dimensional axially symmetrical supersonic flows is developed; it is based on the characteristics theory (represented partly graphically, partly analytically). Thereafter this method is applied to the construction of rotationally symmetrical nozzles" (p. 1).

The shock expansion method of the NACA TN No. 1143 was used to determine the principal aerodynamic characteristics of two-dimensional supersonic airfoils. A discussion is given of the effect of thickness ratio, free-stream Mach number, angle of attack, camber, thickness distribution, and aileron deflection. The calculations indicated that the minimum drag of supersonic airfoils is obtained when the maximum thickness is behind the 0.50 chord. The center of pressure obtained for a symmetrical supersonic airfoil was found to be ahead of the 0.50 chord.

Axial blowers are gaining importance as aircraft engine superchargers. However, the pressure head obtainable per stage is small. Due to the necessary great number of stages, the physical length of the blower becomes too great for an airworthy device. This report discusses several types of construction that permit a reduction in the length of the blower.

From Summary: "An investigation has been conducted in the NACA Cleveland altitude wind tunnel to evaluate the performance characteristics of a modified X24C-4B turbojet engine over a range of simulated altitudes from 5000 to 45,000 feet, simulated flight Mach numbers from 0.25 to 1.07, and engine speeds from 4000 to 12,500 rpm. The engine was modified by the manufacturer to improve the velocity and temperature profiles within the engine. Performance data are graphically presented to show the effect of altitude at a flight Mach number of 0.25 and the effect of flight Mach number at an altitude of 25,000 feet."

"The spanwise lift-distribution measurements in straight air flow on a straight and a 35 deg swept-back tapered wing (NACA airfoil section 0012) are compared with theory for two angles of attack each (alpha approx. 6 deg and alpha approx. 12 deg) in the unstalled range of flow. The complete pressure distribution for the greater of the two angles is indicated" (p. 1).

Note presenting pressure distributions and force measurements in the two-dimensional low-turbulence pressure tunnel at low Mach numbers and high Reynolds numbers of an NACA 65-210 airfoil equipped with a 50-percent-chord plain flap. Tests were carried out for flap deflections of 0, 4, 7, and 10 degrees. These flap deflections provided considerably reduced drag coefficients at life coefficients above the design range of the plain airfoil.

"An investigation has been conducted to determine thermal and pressure-drop performance and the operational characteristics of a Stewart-Warner model 906-B combustion heater. The performance tests covered a range of ventilating-air flows from 500 to 3185 pounds per hour, combustion-air pressure drops from 5 to 35 inches of water, and pressure altitudes from sea level to 41,000 feet. The operational characteristics investigated were the combustion-air flows for sustained combustion and for consistent ignition covering fuel-air ratios ranging from 0.033 to 0.10 and pressure altitudes from sea level to 45,000 feet" (p. 1).

"An investigation was conducted on a full-scale air-cooled cylinder in order to establish an effective means of maintaining maximum-economy spark timing with varying engine operating conditions. Variable fuel-air-ratio runs were conducted in which relations were determined between the spark travel, and cylinder-pressure rise. An instrument for controlling spark timing was developed that automatically maintained maximum-economy spark timing with varying engine operating conditions" (p. 1).