"As part of a general program to study combustion in the engine cylinder and to correlate the phenomena of combustion with the observed performance of actual engines, this paper presents a sketchy outline of what may happen in the engine cylinder during the burning of a charge. It also suggests the type of information needed to supply the details of the picture and points out how combustion time and rate affect the performance of the engine. A theoretical concept of a flame front which is assumed to advance radially from the point of ignition is presented, and calculations based on the area and velocity of this flame and the density of the unburned gases are made to determine the mass rate of combustion" (p. 393).

This report presents the results of tests conducted to determine the effect of different amounts and kinds of cowling on the performance and cylinder temperatures of a standard Wright J-5 engine. These tests were conducted in conjunction with drag and propeller tests in which the same cowlings were used. Four different cowlings were investigated varying from the one extreme of no cowling on the engine to the other extreme of the engine completely cowled and the cooling air flowing inside the cowling through an opening in the nose and out through an annular opening at the rear of the engine. Each cowling was tested at air speeds of approximately 60, 80, and 100 miles per hour.

"Measurements were made to determine the distribution of pressure over one section of an R. A. F. 30 (symmetrical) airfoil with trailing edge flaps. In order to study the effect of scale measurements were made with air densities of approximately 1 and 20 atmospheres. Isometric diagrams of pressure distribution are given to show the effect of change in incidence, flap displacement, and scale upon the distribution. Plots of normal force coefficient versus angle of attack for different flap displacements are given to show the effect of a displaced flap" (p. 589).

This report presents the results of deceleration tests conducted for the purpose of determining the drag characteristics of six airships. The tests were made with airships of various shapes and sizes belonging to the Army, the Navy, and the Goodyear-Zeppelin Corporation. Drag coefficients for the following airships are shown: Army TC-6, TC-10, and TE-2; Navy Los Angeles and ZMC-2; Goodyear Puritan. The coefficients vary from about 0.045 for the small blunt airships to 0.023 for the relatively large slender Los Angeles. This variation may be due to a combination of effects, but the most important of these is probably the effect of length-diameter ratio.

From Summary: "This report presents the results of flight test of the Pitcairn "PCA-2" autogiro. Lift and drag coefficients with the propeller stopped have been determined over approximately a 90 degree range of angles of attack. Based on the sum of fixed-wing and swept-disk areas, the maximum lift coefficient is 0.895, the minimum drag coefficient with propeller stopped is 0.015, and the maximum l/d with propeller stopped is 4.8. Lift coefficients were found also with the propeller delivering positive thrust and did not differ consistently from those found with propeller stopped. Curves of gliding performance included in this report show a minimum vertical velocity of 15 feet per second at an air speed of 36 miles per hour and a flight-path angle of -17 degrees. In vertical descent the vertical velocity is 35 feet per second."

This report gives the theoretical distribution of pressure at lift coefficients of 0, 0.5, 1.0, and 1.5 for 20 airfoils, calculated on the basis of a rigorous potential theory of arbitrary airfoils. It also provides tables from which the characteristics of the airfoils for any angle of attack in 2-dimensional potential flow are readily calculable. The theoretical values of the angles of zero lift, the lift and moment coefficients, and the ideal angles of attack are listed and some comparisons with experiment are indicated. The results presented may be of value in predicting structural loads and also in a correlation of theoretical pressure gradients with profile resistance.

"The aerodynamic forces on an oscillating airfoil or airfoil-aileron combination of three independent degrees of freedom were determined. The problem resolves itself into the solution of certain definite integrals, which were identified as Bessel functions of the first and second kind, and of zero and first order. The theory, based on potential flow and the Kutta condition, is fundamentally equivalent to the conventional wing section theory relating to the steady case" (p. 291).

Report presents the results of a comprehensive experimental study carried out at full scale in the NACA 20-foot wind tunnel, the general purpose of which is to furnish information in regard to the functioning of the power plant and propeller unit under different conditions. This report deals particularly with the problem of the cooling of an airplane engines on the ground. The influence of different nose forms, skirts, flaps, propellers, spinners, and special blowers has been investigated.

"An investigation of the corrosion of light metal alloys used in aircraft was begun at the National Bureau of Standards in 1925 and has for its purpose causes of corrosion in aluminum-rich and magnesium-rich alloys together with the development of methods for its prevention. The results, obtained in an extensive series of laboratory and weather-exposure tests, reveal the relative durability of a number of commercially available materials and the extent to which the application of various surface coatings of oxide alone and with paint coatings afforded additional protection. The paper may be considered as a supplement to NACA report 490" (p. 395).

Report presenting flight tests conducted to measure the lateral-control characteristics of an airplane, equipped with a lateral-control system, in which as the flaps are lowered the ailerons droop and a gradual transition of lateral control from ailerons to spoilers takes place. The variation of maximum rolling velocity with lateral stick movement as obtained in abrupt rudder-locked rolls was satisfactorily smooth except when control was by spoiler alone.

In order to obtain a correlation of drag data from wind-tunnel and flight tests at high Mach numbers, a typical pursuit airplane, with the propeller removed, was tested in flight at Mach numbers up to 0.755, and the results were compared with wind-tunnel tests of a 1/3-scale model of the airplane. The tests results show that the drag characteristics of the test airplane can be predicted with satisfactory accuracy from tests in the Ames 16-foot high-speed wind tunnel of the Ames Aeronautical Laboratory at both high and low Mach numbers. It is considered that this result is not unique with the airplane.

"A 1/6-scale model of the Republic XF-12 vertical tail with stub fuselage and stub horizontal tail was tested in the Langley stability tunnel to determine the aerodynamic characteristics of the model, The investigation included a study of the effects of boundary layer thickness, rudder area, and cover-plate alinement on the aerodynamic characteristics. Tuft studies were made in the vicinity of the junction of the vertical and stub horizontal tails" (p. 1).

Report on sea-level performance tests of a 22-inch-diameter pulse-jet engine on a thrust stand. The tests were conducted at several ram pressures and the entire range of fuel flows that the engine can operate at. Information about the maximum-thrust operation, operating frequency, maximum combustion chamber pressures, and operating lives is provided.

An investigation of the performance of several propellers on the YP-47M airplane at high blade loadings has been conducted in the Cleveland altitude wind tunnel at the request of the Air Materiel Command, Army Air Forces. As part of the program, a study was made of a Curtiss 836-14C2-18R1 four-blade propeller. The investigation was made for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.30, 0.40, and 0.50 for density altitudes from 10,000 to 45,000 feet, engine powers from 150 to 2500 brake horsepower, and for engine speeds from 1000 to 2900 rpm.

At the request of the Bureau of Aeronautics, Navy Department, investigations of the static-pressure losses and total-head distributions of the Westinghouse X24-C-2 inlet screen were made in the induction aerodynamics laboratory at Langley. The screen was investigated in two configurations, both before and after rounding the leading edges of the vanes. Investigations were conducted through air flows up to about pounds per second.

Report presenting the drag of a series of complete airplane-like configurations and their components at transonic velocities using the free-fall method. The configuration tested in this report has a 45 degree sweptback wing of aspect ratio 4.1 mounted forward of the maximum diameter of a 10-inch-diameter body of fineness ratio 12 equipped with stabilizing tail fins. Results are presented as curves showing the variation of drag coefficient with Mach number for the complete configuration and for each component.

"An investigation has been conducted to determine whether three-dimensional flows may be utilized in axial-flow fan and compressor rotors so that the spanwise load distribution may be varied to obtain high pressure rise. Two rotors, one with approximately uniform and one with solid-body downstream tangential-velocity distributions, were designed and tested at the design blade angle" (p. 1).

"By use of the methods of thin airfoil theory, which include effects of compressibility, relations are developed which permit the rapid determination of the pressure distribution over an unstaggered cascade of airfoils of a given profile, and the determination of the profile shape necessary to yield a given pressure distribution for small chord gap ratios. For incompressible flow the results of the theory are compared with available examples obtained by the more exact method of conformal transformation. Although the theory is developed for small chord/gap ratios, these comparisons show that it may be extended to chord/gap ratios of order unity, at least for low speed flows" (p. 1).

Memorandum presenting wind-tunnel tests to determine the aerodynamic characteristics of a 15-percent- and a 35-percent-chord plain trailing-edge flap on the NACA 0006 airfoil section. Simultaneous measurements of section lift, drag, and pitching moment were made over a range of Mach numbers, angles of attack, and flap deflections.

"An investigation was conducted in an altitude test chamber to determine the effects of inlet airflow distortion on the compressor steady-state and surge characteristics of a high-pressure ratio, axial-flow turbojet engine. Circumferential-type inlet flow distortions were investigated, which covered a range of distortion sector angles from 20 deg to 168 deg and distortion levels up to 22 percent. The presence of inlet airflow distortions at the compressor face resulted in a substantial increase in the local pressure ratio in the distorted region, primarily for the inlet stages" (p. 1).

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from June 2, 1947 to June 7, 1947, are presented.

The gust and draft velocities evaluated from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from May 13 to May 29, 1947 are presented.

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from August 13, 1947 to August 15, 1947 are presented.

Report presenting a wind tunnel investigation to determine the downwash angles, dynamic pressure loss, and wake width behind wings with sweep angles of 45, 30, and 0 degrees. Results indicated that the spanwise distribution of downwash was affected by sweep in a manner similar to span loading, increased toward the root by sweepforward and toward the tip by sweepback.