This report describes test made in the Variable Density Wind Tunnel of the NACA to determine the possibility of controlling the boundary layer on the upper surface of an airfoil by use of the low pressure existing near the leading edge. The low pressure was used to induce flow through slots in the upper surface of the wing. The tests showed that the angle of attack for maximum lift was increased at the expense of a reduction in the maximum lift coefficient and an increase in the drag coefficient.

From Summary: "Results are presented of the drag tests of six bodies of revolution with systematically varying shapes and with a fineness ratio of 5. The forms were derived from source-sink distributions, and formulas are presented for the calculation of the pressure distribution of the forms. The tests were made in the N.A.C.A. variable-density tunnel over a range of values of Reynolds number from about 1,500,000 to 25,000,000. The results show that the bodies with the sharper noses and tails have the lowest drag coefficients, even when the drag coefficients are based on the two-thirds power of the volume. The data shows the most important single characteristic of the body form to be the tail angle, which must be fine to obtain low drag."

From Summary: "A preliminary investigation of the stalling processes of four typical airfoil sections was made over the critical range of the Reynolds Number. Motion pictures were taken of the movements of small silk tufts on the airfoil surface as the angle of attack increased through a range of angles including the stall. The boundary-layer flow also at certain angles of attack was indicated by the patterns formed by a suspension of lampblack in oil brushed onto the airfoil surface. These observations were analyzed together with corresponding force-test measurements to derive a picture of the stalling processes of airfoils."

Note describing the variation in the number of revolutions per minute and provides simple formulas that allow for advanced calculation to be made of the variation of propeller speed with variation of one or more dimensions of the propeller and allow the necessary corrections to be applied.

Report presenting a theoretical approach to determine the lateral frequency response of a fighter airplane to side gusts and rolling gusts at a Mach number of 0.7 and an altitude of 30,000 feet. Frequency response and power spectral density were determined with the controls fixed and in combination with three different basic types of attitude autopilots.

"By use of an approximate equation for the wave drag of slender bodies of revolution in a supersonic flow field, the optimum shapes of certain boattail bodies are determined for minimum wave drag. The properties of three specific families of bodies are determined, the first family consisting of bodies having a given length and base area and a contour passing through a prescribed point between the nose and base, the second family having fixed length, base area, and maximum area, and the third family having given length, volume, and base area. The method presented is easily generalized to determine minimum-wave-drag profile shapes which have contours that must pass through any prescribed number of points" (p. 1).

Report presenting testing in high-speed flight with a fighter airplane to determine the effect of chordwise pressure distribution resulting from a minor modification in the contour of the wing upper surface. A faired bulge was added to the contour and chordwise pressure distributions were obtained on the original and modified contours.

From Introduction: "The analysis of flight data in the present report is, to a large extent, based on analyses and information contained in references 1 and 2 for wing deflections, reference 3 for horizontal-tail parameters, reference 4 for airplane lift-curve slopes and angles of zero lift, and reference 5 for wing centers of pressure."

Report presenting a flight investigation to determine the contributions of wing, tail, and fuselage to the total airplane lift of a propeller-driven fighter-type airplane. The tests occurred over a range of Mach numbers. The loads on the various airplane components were measured by the use of calibrated strain-gage installations located at the roots of the wings and horizontal tail surfaces.

Note presenting symbols and definitions of various airspeed terms that have been adopted as standard by the NACA Subcommittee on Aircraft Structural Design. the equations, charts, and tables required in the evaluation of true airspeed, calibrated airspeed, equivalent airspeed, impact and dynamic pressures, and Mach and Reynolds numbers have been compiled.

Note presenting pressure distribution measurements made on the wing of a fighter-type airplane to determine the span loading and to compare center-of-pressure results with those obtained by strain-gage measurements on the same airplane during a previous flight investigation. Flight tests were all made at a pressure altitude of about 30,000 feet and covered a Mach number range from approximately 0.35 to 0.81. Results regarding additional air load, spanwise center of pressure of additional air load, basic air load distribution, and span loading during a stall and buffeting are provided.

"The primary objectives of the present paper are to report the horizontal-tail-loads measurements for configuration B which have not previously been reported and to summarize the horizontal-tail-loads results obtained with both configurations. The manner in which the aerodynamic-loads data were analyzed to include structural temperature effects and fuselage flexibility effects constitutes an important part of the present paper" (p. 1).

"The pack method for determining compressive stress-strain graphs described in NACA Report No. 649 has been modified to extend it's application to thinner gages and stronger materials. The principal modifications consisted in the provision of additional support against instability cementing the specimens of the pack together with fused shellac and the provision of special clamps to hold the specimens together while the test is in progress. The shellac was found to increase the buckling load of the pack without any appreciable effect on the compressive stress-strain graph of the material" (p. 1).

"A subpress for compressive tests is described. The subpress was designed primarily for use in developing and investigating methods for testing thin sheet metal in compression. Provision was made for testing fixed-end and flat-end specimens with or without various types of lateral support against buckling. Compressive stress-strain data for a sheet of 0.032-inch 24S-RT aluminum alloy were obtained with the subpress by the pack method and by the single-thickness method" (p. 1).

Note presenting tensile and compressive stress-strain curves, stress-deviation curves, and secant modulus-stress curves for longitudinal and transverse specimens of magnesium alloy J-1 sheets 0.032 and 0.102 inch thick. Significant differences were found between the tensile and compressive stress-strain curves and between the compressive stress-strain curves for the longitudinal and transverse questions.

Report presenting a series method of determining two-dimensional vortex paths is considered and applied to the computation of vortex positions behind a slender equal-span cruciform wing at any angle of bank as a function of the distance behind the trailing edge.

Report presenting a theoretical treatment of absorption problems that considers the following cases: radiation is normal to an absorber with plane parallel surfaces, radiations are of several polyenergetic types, induced radioactive isotopes decay to stable atoms in multistep decay processes, and radiations from the absorber affect the time-dependency of the source activity. Radiation from intermediate isotopes can become more dangerous than the original activity, so the entire range of radiations must be accounted for.

Report presenting tables for determining the total-absorption coefficients as well was the intensities and spectral distribution of gamma rays at any scattering angle. Both experimental and computed data on gamma rays of quantum energies up to 20 million electron volts for all elements which have significant data available are provided. The accuracy of results is obtained by the use of tables.

Report presenting friction and wear experiments conducted to explore the effects of high temperature, varied chlorine content, sulfur catalysis, and preformation of sulfide films on boundary lubrication with reactive gases. Results regarding sulfur hexafluoride, dichlorodifluoromethane, chlorotrifluoromethane, chlorotrifluorometahne plus sulfur hexafluoride, and dichlorodifluoromethane plus sulfur hexafluoride are provided.

Report presenting the development of an asymmetric type of adjustable supersonic nozzle suitable for application to wind tunnels. This type of nozzle permits continuous adjustment of the test-section Mach number without the requirement of flexible walls.

From Summary: "An analysis is given of the oscillating motion of a ballistic missile which upon entering the atmosphere is angularly misaligned with respect to the flight path. The history of the motion for some example missiles is discussed from the point of view of the effect of the motion on the aerodynamic heating and loading. The miss distance at the target due to misalignment and to small accidental trim angles is treated. The stability problem is also discussed for the case where the missile is tumbling prior to atmospheric entry."

From Summary: "A method is presented for the rapid calculation of the pressure distribution over an airfoil section when the normal-force distribution and the pressure distribution over the "base profile" (i.e., the profile of the same airfoil were the camber line straight and the resulting airfoil at zero angle of attack) are known. This note is intended as a supplement to N.A.C.A. Report Nos. 631 and 634 wherein methods are presented for the calculation of the normal-force distribution over plain and flapped airfoils, respectively, but not of the pressures on the individual surfaces. Base-profile pressure-coefficient distributions for the usual N.A.C.A. family of airfoils, which are also suitable for several other commonly employed airfoils, are included in tabular form. With these tabulated base-profile pressures and the computed normal-force distributions, pressure distributions adequate for most engineering purposes can be obtained."

A simplified analysis of the velocity and deceleration history of missiles entering the earth's atmosphere at high supersonic speeds is presented. The results of this motion analysis are employed to indicate means available to the designer for minimizing aerodynamic heating. The heating problem considered involves not only the total heat transferred to a missile by convection, but also the maximum average and local time rates of convective heat transfer.

Report presenting a consideration of the development of the laminar boundary layer in a compressible fluid. Formulas are given for determining the boundary-layer thickness and the boundary-layer Reynolds number, which is a measure of the boundary-layer stability, for airfoils and bodies of revolution.