"A high-speed wind-tunnel investigation of the aerodynamic characteristics of a full-scale model of the Consolidated Vultee Lark indicates that the missile possesses satisfactory longitudinal-stability and-control characteristics throughout the Mach number range from 0.2 to 0.85, but that the maximum lift coefficients developed are not high enough to insure interception of the target at high altitudes. A reduction in wing loading appears advisable. Although the static longitudinal stability at zero angle of attack changes with Mach number and with lift coefficient, satisfactory control should be possible at all times as the tails retain their relatively large effectiveness throughout the range of Mach numbers and lift coefficients tested" (p. 1).

"Flight tests were conducted on a R-2800-21 engine in the P-47G airplane to determine the effect on the wall temperatures of cylinder 10 of throttling the charge in the intake pipe and of injecting a water-ethanol coolant into the intake pipe. Cylinder 10 was chosen for this investigation because it runs abnormally hot (head temperatures of the order of 45 F higher than those of the next hottest cylinder) at the medium and high-power conditions. Tests with interchanged cylinders showed that the excessive temperatures of cylinder 10 were inherent in the cylinder location and were not due to the mechanical condition of the cylinder assembly" (p. 1).

"Knock-limited performance data were obtained for three fuels on an R-1830-75 engine in a B-24D airplane at engine speeds of 1800, 2250, and 2600 rpm, a spark advance of 25 degrees B.T.C., and carburetor-air temperatures of 85 F for 1800 and 2250 rpm and 100 F for 2600 rpm. The test fuels were a blend of 80 percent 28-R plus 20 percent triptane (leaded to 4.5 ml TEL/gal), a blend of 80 percent 28-R plus 15 percent toluene (leaded to 4.5 ml TEL / gal), and 28-R fuel. The knock-limited manifold pressure of the toluene blend depreciated more in the lean region than the triptane blend or 28-R fuel" (p. 1).

"An investigation of a 1/7-scale powered model of the Kaiser Fleetwing all-wing airplane was made in the Langley full-scale tunnel to provide data for an estimation of the flying qualities of the airplane. The analysis of the stability and control characteristics of the airplane has been made as closely as possible in accordance with the requirements of the Bureau of Aeronautics, Navy Department's specifications, and a summary of the more significant conclusions is presented as follows. With the normal center of gravity located at 20 percent of the mean aerodynamic chord, the airplane will have adequate static longitudinal stability, elevator fixed, for all flight conditions except for low-power operation at low speeds where the stability will be about neutral" (p. 1).

"A laboratory investigation was made on a Holley 1685-HB carburetor mounted on an R-2600-13 supercharger assembly to determine the icing characteristics and the heated-air de-icing requirements of this portion of the B-25D airplane induction system. Icing has been found to be most prevalent at relatively small throttle openings and, consequently, all runs were made at simulated 60-percent normal rated power condition. Icing characteristics were determined during a series of 15-minute runs over a range of inlet-air conditions. For the de-icing investigation severe impact ice was allowed to form in the induction system and the time required for the recovery of 95 percent of the maximum possible air flow at the original throttle setting was then determined for a range of wet-bulb temperatures" (p. 1).

"An investigation was conducted in the Cleveland altitude wind tunnel to determine the aerodynamic characteristics and the oil delivery critical altitude of the oil-cooler installation of an XTB2D-1 airplane. The investigation was made with the propeller removed end with the engine operating at 1800 brake horsepower, an altitude of 15,000 feet (except for tests of oil-delivery critical altitude), oil-cooler flap deflections from -20 degrees to 20 degrees and inclinations of the thrust axis of 0 degrees, 1.5 degrees, and 6 degrees. At an inclination of the thrust axis of 0 degrees and with the propeller operating, the total-pressure recovery coefficient at the face of the oil cooler varied from 0.84 to 1.10 depending on the flap deflection" (p. 1).

"In order to determine the aerodynamic effects of an auxiliary belly fuel tank on the Grumman F8F-1 airplane, a wind-tunnel investigation was made on a 1/5 - scale model of the Grumman XF8F-1 airplane. Pitch and yaw tests were made with the model in the cruising and landing configurations for windmilling and take-off power conditions. Tuft studies and static-pressure measurements were also made to determine the flow characteristics in the region of the fuel tank" (p. 1).

"The cooling characteristics of three R-1830-94 engines, two of which were mounted in a test stand and the other in a B-24D airplane, were investigated and the results were compared. The flight tests were made at a pressure altitude of 7000 feet; the test-stand runs were made at ground-level atmospheric conditions. Three cooling runs were made for each engine: variable cooling-air pressure drop, variable carburetor-air flow, and variable fuel-air ratio" (p. 1).

:Spin tests have been performed in the Langley 20-foot free-spinning tunnel on a 1/18-scale model of the Fairchild XNQ-1 airplane. The spin and recovery characteristics of the model were determined for the normal gross-weight loading and for two variations from this loading - center of gravity moved rearward and relative mass distribution increased along the fuselage. These tests were performed for two vertical-tail plan forms. The investigation also included simulated pilot-escape tests and rudder-force tests" (p. 1).

"As part of an investigation to increase the power output of the V-1710-93 engine at altitude, the engine-stage supercharger was combined with a constant-area vaneless diffuser designed to improve the performance of the engine-stage supercharger at the rated engine operating point. The performance of the modified supercharger was investigated in a variable-component supercharger test rig and compared with that of the standard supercharger with an 8-vaned diffuser. A separate evaluation of the component efficiencies and a study of the flow characteristics of the modified supercharger was made possible by internal diffuser instrumentation" (p. 1).

"Three modifications of the auxiliary-stage supercharger for the V-1710-93 engine were designed and tested as part of an investigation to improve the power output and the altitude performance of the engine. A 12-vane diffuser was substituted for the standard 11-vane diffuser, and a vaneless discharge passage and a modified scroll were designed to increase the flow capacity of the supercharger and thereby to increase the performance at the high volume flows required by the engine. With the 12-vane diffuser installed and the carburetor replaced by an adapter, the equivalent volume flow at the peak efficiency point was increased 25 percent at the lowest speed investigated and 9.5 percent at the highest speed" (p. 1).

The 19xB compressor, which replaces the 19B compressor and has the same length and diameter 88 the 19B compressor, was designed with 10 stages to deliver 30 pounds of air per second for a pressure ratio of 4.17 at an equivalent speed of 17,000 rpm; the 19B was designed with six stages for a pressure ratio of 2.7 at the same weight flow and speed as the 19XB compressor. The performance characteristics of the new compressor were determined at the NACA Cleveland laboratory at the request of the Bureau of Aeronautics, Navy Department.

"A supersonic inlet with supersonic deceleration of the flow entirely outside of the inlet is considered. A particular arrangement with fixed geometry having a central body with a circular annular intake is analyzed, and it is shown theoretically that this arrangement gives high pressure recovery for a large range of Mach number and mass flow and therefore is practical for use on supersonic airplanes and missiles. For some Mach numbers the drag coefficient for this type of inlet is larger than the drag coefficient for the type of inlet with supersonic compression entirely inside, but the pressure recovery is larger for all flight conditions" (p. 1).

From Introduction: "Performance results of the tail-pipe burning investigation on the TG-180 turbojet engine and a comparison of experimental results with theoretical calculations are presented."

From Summary: "An investigation of a heated jet was conducted in conjunction with tests of an axial-flow jet-propulsion engine in the Cleveland altitude wind tunnel. Pressure and temperature surveys were made across the jet 10 and 15 feet behind the jet-nozzle outlet of the engine. Surveys were obtained at pressure altitudes of 10,000, 20,000, 30,000, and 40,000 feet with test-section velocities from 30 to 110 feet per second and test-section temperatures from 60 F to -50 F. From measurements taken throughout the operable range of engine speeds, tail-pipe outlet temperatures from 500 F to 1250 F and jet velocities from 400 to 2200 feet per second were obtained."

This paper presents the results of the aileron investigation and includes rolling-moment, yawing-moment, and aileron hinge-moment coefficients and pressure coefficients across the aileron-balance seal through a range of angle of attack, tab deflection, and aileron deflection with flaps neutral and deflected 20 degrees and 55 degrees. Some of the effects of wing roughness and balance seal leakage on the aileron and tab characteristics are also presented.

From Summary: "An investigation was conducted in the Langley 19-foot pressure tunnel to determine the lift, drag, pitching-moment and stalling characteristics of a 1/4 -scale partial-span model of the left wing of the Republic XF-12 airplane. The effects of a duct inlet, located between the nacelles at the leading edge of the wing, on those characteristics were also investigated. The Reynolds numbers for the investigation covered a range from 4,500,000 to 8,600,000. The results of the investigation indicated that maximum lift coefficients of 1.36, 1.71, and 2.11 were measured on the model with flaps neutral and deflected 20 deg and 55 deg, respectively at a Reynolds number of 8,600,000."

From Summary :"An investigation was conducted to evaluate the possibilities of utilizing the high-performance characteristics of triptane and xylidines blended with 28-R fuel in order to increase fuel economy by the use of high compression ratios and maximum-economy spark setting. Full-scale single-cylinder knock tests were run with 20 deg B.T.C. and maximum-economy spark settings at compression ratios of 6.9, 8.0, and 10.0, and with two inlet-air temperatures. The fuels tested consisted of triptane, four triptane and one xylidines blend with 28-R, and 28-R fuel alone."

An investigation was conducted to determine the effects of three design modifications of the original NACA injection impeller on the performance of an R-3350 engine. Different methods of injecting the fuel into the impeller air stream were studied and evaluated from the individual cylinder fuel-air ratios and the resulting cylinder temperatures. Each impeller was tested for a range of engine powers normally used in flight operation. The relatively simple design of the original injection impeller produced approximately the same mixture- and temperature-distribution characteristics as the modified impellers of more complex design. None of the modifications appreciably affected the manifold pressure, the combustion-air flow, nor the throttle angle required to maintain a given engine power,.

"A dynamically similar model of the Army P-38 airplane was tested to determine the best way to land this airplane on the water and to determine its probable ditching performance. The tests consisted of ditching the model at various landing attitudes, flap settings, speeds, weights, and conditions of simulated damage. The model was ditched in calm water from the tank towing carriage and a few ditching were made in both calm and rough water at the outdoor catapult" (p. 1).

"Because the results of preliminary flight tests had indicated the P-63A-1 airplane possessed insufficient directional stability, the NACA and the manufacturer (Bell Aircraft Corporation) suggested three vertical-tail modifications to remedy the deficiencies in the directional characteristics. These modifications included an enlarged vertical tail formed by adding a tip extension to the original vertical tail, a large sharp-edge ventral fin, and a small dorsal fin. The enlarged vertical tail involved only a slight increase in total vertical-tail area from 23.73 to 26.58 square feet but a relatively much larger increase in geometric aspect ratio from 1.24 to 1.73 based on height and area above the horizontal tail" (p. 1).

"An investigation of the 19XB-2A gas turbine is being conducted at the Cleveland laboratory to determine the effect on turbine performance of various inlet pressures, inlet temperatures, pressure ratios, and wheel speeds. The engine of which this turbine is a component is designed to operate at an air flow of 30 pounds per second at a compressor rotor speed of 17,000 rpm at sea-level conditions. At these conditions the total-pressure ratio is 2.08 across the turbine and the turbine inlet total temperature is 2000 degrees R" (p. 1).

From Summary: "Tests have been made in Langley tank no. I of a dynamic model of the Consolidated Vultee PB2Y-3 airplane. These tests were made using an alternate hull form, the purpose of which was to reduce the bow spray and eliminate the landing instability which are objectionable features of the production design. The major differences from the PB2Y-3 hull included a deeper step to improve the landing stability , and a lengthened forebody and increased beam to reduce the sway in the propellers and on the flaps. The tests showed that the spray characteristics of the revised hull form were much better than that to the production design. In addition the take-off and landing stability of the model with the alternate hull were satisfactory."

From Summary: "Tests of a model of the XJR2F-Y amphibian were made in Langley tank no. to determine the spray characteristics and the take-off and landing stability. At a gross load of 22,000 pounds full size, spray entered the propeller disk only at a very narrow range of speeds. The spray striking the flaps was not excessive and no appreciable wetting of the tail surfaces was noted. The trim limits of stability appeared to be satisfactory and the upper-limit porpoising was not violent."