Memorandum presenting the experimental results of tests to confirm the contribution to the study of normal burning in gaseous carbureted mixtures.

Memorandum presenting an investigation concerning the limits of detonation in gaseous mixtures. In regards to the results, by progressive dilution of the explosive, the course of the chemical reaction becomes slower and slower until finally the transformation within the reaction zone becomes so slow that it is not there completed.

"Two screw propellers, a normal airplane propeller with a pitch/diameter ratio H/D = 0.5 and a helicopter propeller H/D = 0.2 were tested in the large wind tunnel of the Gottigen Aerodynamic Institute. With both propellers the angle between the propeller axis and the direction of the wind was varied from 0 to 90 degrees. In addition to the three force and the three moment components in a wind-fast coordinate system, the corresponding components in a propeller-fast coordinate system, a total of six force and six moment components, together with the propulsive efficiency, were measured or calculated from measurements" (p. 1).

In order to demonstrate the importance of free-wheeling propellers, this report considers the braking effect of a propeller on a stopped engine when the propeller is rigidly connected with the engine shaft and also when mounted on a free-wheel hub. The cases of propellers of asymmetric and symmetric section are discussed. The author describes the mechanism of the free-wheel propeller as constructed for this test. The results obtained with the device mounted on a 1,000 horsepower two-engine airplane are given.

One of the serious sources of difficulties in variable pitch propellers is the turning moment or torque due to the centrifugal force which tends to bring the mean plane of the blades into the plane of rotation. This moment, which is found elsewhere only in propellers with removable blades, is so great that the aerodynamic forces, as regards their effect on the torsion, become entirely negligible in comparison with it. This report presents the Ratier Company's solution to changing the pitch of airplane propellers.

The purpose of this section is to survey the present status of scientific knowledge of the causes which produce drag, in order, if possible, to establish the relation between the individual results and the actual phenomena which demonstrate the fundamental importance of surface conditions. A discussion of the boundary layer is followed by: relations between frictional and form drag, application to profile-drag measurements, and different kinds of roughness. High-pressure wind tunnel tests are discussed along with roughness and maximum lift.

The present report contains the results thus far obtained and is intended to form the basis of further tests on using the momentum method. The method of testing is presented in detail and the photographs taken during these tests are interpreted.

Tests were made to determine the crushing strength of a riveted joint, in order to define the difference in crushing stregth between a strictly bolted joint and a riveted joint. The object was to tabulate the crushing strength by failure on various plate thicknesses for a one-rivet double-shear riveted joint.

This report includes strength of riveted joints in duralumin, descriptions of test procedure and results of tests. Tabulated data includes: curshing strength by failure for various conditions, shearing strength of hole edge zone in direction of tearing, tearing strengths of plates weakened by rivet holes, and enlargement of holes at beginning of break.

This report includes descriptive material on rivet inspection, types of rivets and sizes. Tabular data on shearing strength of rivets at failure, ultimate shear of various rivets, tensile tests of rivet plate, and tensile strength values of riveted joints are provided.

"For some time the D.V.L. has been investigating the question of applicability of Handley Page slotted wings to German airplanes. Comparitive gliding tests were made with open and closed slots on an Albatros L 75 airplane equipped with the Handley Page "auto control slots." This investigation served to determine the effect of the auto control slot on the properties and performances of airplanes at large angles of attack. The most important problems were whether the angle of glide at small angles of attack can be increased by the adoption of the auto control slot and, in particular, as to whether the flight characteristics at large angles of attack are improved thereby and equilibrium in gliding flight is guaranteed even at larger than ordinary angles of attack" (p. 1).

"The effect of a slotted wing depends essentially on the fact that a secondary flow branches off from the main flow and passes to the suction side of the profile. It is thus possible to delay the separation greatly and increase the lift. The practical aspect of the slotted wing is less known in Germany, especially the results obtained during the last three years since the introduction of the 'auto control slot'" (p. 1).

This paper presents a relative determination of the wrinkling of a plate wall beam with variable number of supports and methods of attachment. The discussion is based entirely on tests with extensometer readings and number of wrinkles, with complete web and with cutout sections. The author notes that the number of corrugations increase with added stress, keeping constant edge spacing.

The method of riveting by forming the closing head under increasing pressure or by a series of hammer blows is investigated. The question as to the best edge distance, i.e. that distance from the rivet center to the plate edge below which it is unadvisable to go and, at the same time useless to go beyond, was examined. The slippage of plates which occurs under the effect of a certain stress, does not completely disappear on unloading.

Relative altimetry is of great importance for increasing the safety in aerial transportation, because it makes possible safe flying at night, by poor visibility, and when landing. Among the instruments of this type is the Behm sounder, which operates on an acoustic principle. Acoustic altimetry in general and the Behn sounder, in particular, are covered in this report.

A counter-propeller is a fixed propeller smaller than the main propeller, mounted either fore or aft of the latter and performing the function of changing the direction of motion of the fluid filaments, which naturally tend to adopt a helicoidal form. This paper presents a consideration of the real advantage of counter-propellers on aircraft and the best shape of the blades. First, the author determines the possible energy absorption by the tangential increments. This process will be facilitated by the examination of the polygons of the relative velocities fore and aft of the generic section, of radius r, of one of the blades of the propeller.

"This report is intended to furnish bases for load assumptions in the designing of airplane controls. The maximum control forces and quickness of operation are determined. The maximum forces for a strong pilot with normal arrangement of the controls is taken as 1.25 times the mean value obtained from tests with twelve persons. Tests with a number of persons were expected to show the maximum forces that a man of average strength can exert on the control stick in operating the elevator and ailerons and also on the rudder bar" (p. 1).

The present investigation is an endeavor to express the jolting stresses, designated as landing impacts, undergone by seaplanes in landing and taking off from rough water, as functions of specific factors, in order to enable the evaluation of empirically obtained results and thus acquire theoretical data for the construction of seaplane floats and hulls.

The tapered wing shape increases the lift in the middle of the wing and thus reduces the bending moment of the lifting forces in the plane of symmetry. Since this portion of the wing is the thickest, the stresses of the wing material are reduced and desirable space is provided for stowing the loads in the wing. This statically excellent form of construction, however, has aerodynamic disadvantages which must be carefully weighed, if failures are to be avoided. This treatise is devoted to the consideration of these problems.

Previous investigations on the strength characteristics and structure of wood in construction are analyzed and a method of representation is developed suitable for the use of designers.

These calculations were based on the shape of the ZR III, with the following simplifications: cars, fins, and rudders removed; all cross sections replaced by equivalent circular cross sections. Under these assumptions the pressure distribution was calculated for the following cases: symmetrical case, or flow parallel to the axis; unsymmetrical case, or flow at an angle to the axis. In both cases the simple potential flow first forms the basis for the determination of the pressure distribution.

This report concerns propulsion by means of rockets. The author concerns himself mainly with efficiency of propulsion and he defines and mathematically expresses those efficiencies.

This report presents a calculation of the torsional frequencies of revolving bars with allowance for the air forces. Calculation of the flexural or bonding frequencies of revolving straight or tapered bars in terms of the angular velocity of revolution. Calculation on the basis of Rayleigh's principle of variation. There is also a discussion of error estimation and the accuracy of results. The author then provides an application of the theory to screw propellers for airplanes and the discusses the liability of propellers to damage through vibrations due to lack of uniform loading.

A discussion of the Flettner rotor is presented from a nautical and economic viewpoint, and although it was a failure, the experimental and theoretical inventions cannot be disregarded. The following critical and experimental investigation will show the relations and applicability of the theories and practical applications. The Magnus effect is described in detail and a discussion and critical review of the Magnus effect is included.