Aluminum-based spent nuclear fuel from foreign and domestic research reactors is being consolidated at the Savannah River Site (SRS) for ultimate disposal in the Monitored Geologic Repository. The melt-dilute treatment technology has been developed to consolidate fuel assemblies by a melting/casting process in which depleted uranium is added to reduce enrichment below 20 percent 235-U. The melt-dilute product is essentially a binary uranium-aluminum alloy to which neutron absorber materials may be readily added.

This effort will provide a technical basis to assure safe and efficient system operation of the melt-dilute process and have general applicability to off-gas streams.

This paper reviews the candidate legacy materials and addresses adaptation of the melt-dilute technology to treat DOE legacy waste streams.

To assess the effects of long-term, low-dose-rate neutron exposure on mechanical strength and ductility, tensile properties were measured on 12% and 20% cold-worked Type 316 stainless steel. Samples were prepared from reactor core components retrieved from the EBR-II reactor following final shutdown. Sample locations were chosen to cover a dose range of 1-56 dpa at temperatures from 371-440 C and dose rates from 0.5-5.8 x10{sup -7} dpa/s. These dose rates are approximately an order of magnitude lower than those of typical EBR-II test sample locations. The tensile tests for the 12% CW material were performed at 380 C and 430 C while those for the 20% CW samples were performed at 370 C. In each case, the tensile test temperature approximately matched the irradiation temperature. To help understand the tensile properties, microstructural samples with similar irradiation history were also examined. The strength and loss of work hardening increase the fastest as a function of irradiation dose for the 12% CW material irradiated at lower temperature. The decrease in ductility with increasing dose occurs more rapidly for the 12% CW material irradiated at lower temperature and the 20% cold-worked material. Post-tensile test fractography indicates that at higher dose, the 20% CW …

The Advanced Photon Source (APS) storage ring operation at higher beam current is one of the potential enhancements to increase beam brilliance. However, this would impact the beamline components and high heat-load crotch absorbers. Thus, this analysis is conducted to better understand the impact of higher beam current on water-cooled crotch absorbers, made out of Glidcop, without introducing any heat-related problems.

This paper summarizes the inspections and inspection results in conjunction with the corrosion experience of aluminum-clad SNF in basin storage.

This final technical report describes the research carried out during the final two months of the no-cost extension ending 11/14/01. The primary goals of the project were (1) to determine the potential for transformation of Cr(VI) (oxidized, mobile) to Cr(III) (reduced, immobile) under unsaturated conditions as a function of different levels and combinations of (a) chromium, (b) nitrate (co-disposed with Cr), and (c) molasses (inexpensive bioremediation substrate), and (2) to determine population structure and activity in experimental treatments by characterization of the microbial community by signature biomarker analysis and by RT-PCR and terminal restriction fragment length polymorphism (T-RFLP) and 16S ribosomal RNA genes. It was determined early in the one-year no-cost extension period that the T-RFLP approach was problematic in regard to providing information on the identities of microorganisms in the samples examined. As a result, it could not provide the detailed information on microbial community structure that was needed to assess the effects of treatments with chromium, nitrate, and/or molasses. Therefore, we decided to obtain the desired information by amplifying (using TR-PCR, with the same primers used for T-RFLP) and cloning 16S rRNA gene sequences from the same RNA extracts that were used for T-RFLP analysis. We also decided …

None

None

The authors consider the link scheduling problem for packet radio networks which is assigning channels to the connecting links so that transmission may proceed on all links assigned the same channel simultaneously without collisions. This problem can be cast as the distance-2 edge coloring problem, a variant of proper edge coloring, on the graph with transceivers as vertices and links as edges. They present efficient approximation algorithms for the distance-2 edge coloring problem for various classes of graphs.

The purpose of this project was to provide the resources and capabilities necessary to permit the State of Oklahoma to conduct Area of Review (AOR) variance analysis on a statewide level. The project allows for the analysis and identification of areas which may qualify for AOR variances, the correlation of information from various databases and automated systems to conduct AORs in area which do not qualify for variances, the evaluation of the risk of pollution, during permitting and monitoring, using risk-based data analysis, and the ability to conduct spatial analysis of injection well data in conjunction with other geographically referenced information.

None

None

A paradigm is developed for generating structured finite element models from solid models by means of implicit surface definitions. The implicit surfaces are defined by radial basis functions. Internal features, such as material interfaces, sliding interfaces and cracks are treated by enrichment techniques developed in the extended finite element method (X-FEM). Methods for integrating the weak form for such models are proposed. These methods simplify the generation of finite element models. Results presented for several examples show that the accuracy of this method is comparable to standard unstructured finite element methods.

Experimental tests have been undertaken to determine safe levels of laser exposure on bare high explosive (HE) samples and on common metals used in intimate contact with HE. Laser light is often focused on bare HE and upon metals in contact with HE during alignment procedures and experimental metrology experiments. This paper looks at effects caused by focusing laser beams at high energy densities directly onto the surface of various bare HE samples. Laser energy densities (fluence) exceeding 19 kilowatts/cm{sup 2} using a 5-milliwatt, 670 nm, cw laser diode were generated by focusing the laser down to a spot size diameter of 4 microns. Upon careful inspection, no laser damage was observed in any of the HE samples illuminated at this fluence level. Direct laser exposure of metals directly contacting HE surfaces was also tested. Laser energy densities (fluence) varying from 188 Watts/cm{sup 2} to 12.7 KW/cm{sup 2} were generated using an 11-Watt, 532 nm frequency-doubled Nd:YAG cw laser with focal spot size diameters as small as 100 microns. These measurements look at the temperature rise of the surface of the metal in contact with HE when laser energy is incident on the opposite side of the metal. The temperature …

The U.S. Intelligence Community continues to adjust to the post-Cold War environment. Congressional and executive branch initiatives have emphasized enhancing cooperation among the different agencies that comprise the Community by giving greater managerial authority to the Director of Central Intelligence (DCI).

This report reviews the ecological quality profile methodology and results for the Hanford Site. It covers critical ecological assets and terrestrial resources, those in Columbia River corridor and those threatened and engdangered, as well as hazards and risks to terrestrial resources. The features of a base habitat value profile are explained, as are hazard and ecological quality profiles.

None

This document summarizes progress on Cooperative Agreement DE-FC26-01NT41185, Pilot Testing of Mercury Oxidation Catalysts for Upstream of Wet FGD Systems, during the time period April 1, 2002 through June 30, 2002. The objective of this project is to demonstrate at pilot scale the use of solid honeycomb catalysts to promote the oxidation of elemental mercury in the flue gas from coal combustion. The project is being funded by the U.S. DOE National Energy Technology Laboratory under Cooperative Agreement DE-FC26-01NT41185. EPRI, Great River Energy (GRE), and City Public Service (CPS) of San Antonio are project co-funders. URS Group is the prime contractor. The mercury catalytic oxidation process under development uses catalyst materials applied to honeycomb substrates to promote the oxidation of elemental mercury in the flue gas from coal-fired power plants that have wet lime or limestone flue gas desulfurization (FGD) systems. Oxidized mercury is removed in the wet FGD absorbers and co-precipitates in a stable form with the byproducts from the FGD system. The co-precipitated mercury does not appear to adversely affect the disposal or reuse properties of the FGD byproduct. The current project will test previously identified, effective catalyst materials at a larger, pilot scale and in a commercial …

Pulsed lasers offer the capability of rapid material removal. Here we present simulations of steel coupon tests by two solid state heat capacity lasers built at LLNL. Operating at 1.05 pm, these deliver pulse energies of about 80 J at 10 Hz, and about 500 J at 20 Hz. Each is flashlamp-pumped. The first laser was tested at LLNL, while the second laser has been delivered to HELSTF, White Sands Missile Range. Liquid ejection appears to be an important removal mechanism. We have modeled these experiments via a time-dependent code called THALES, which describes heat transport, melting, vaporization, and the hydrodynamics of liquid, vapor, and air. It was previously used, in a less advanced form, to model drilling by copper vapor lasers [1] . It was also used to model vaporization in beam dumps for a high-power laser [2]. The basic model is in 1D, while the liquid hydrodynamics is handled in 2D.

None

This paper will discuss the application of high performance component software technology developed for a complex physics simulation development effort. The primary tool used to build software components is called Babel and is used to create language-independent libraries for high performance computers. Components were constructed from legacy code and wrapped with a thin Python layer to enable run-time scripting. Low-level components in Fortran, C++, and Python were composed directly as Babel components and invoked interactively from a parallel Python script.

An appraisal of the potential performance of different Low Energy Cooling (LEC) systems in nonresidential buildings in California is being conducted using computer simulation. The paper presents results from the first phase of the study, which addressed the systems that can be modeled, with the DOE-2.1E simulation program. The following LEC technologies were simulated as variants of a conventional variable-air-volume system with vapor compression cooling and mixing ventilation in the occupied spaces: Air-side indirect and indirect/direct evaporative pre-cooling. Cool beams. Displacement ventilation. Results are presented for four populous climates, represented by Oakland, Sacramento, Pasadena and San Diego. The greatest energy savings are obtained from a combination of displacement ventilation and air-side indirect/direct evaporative pre-cooling. Cool beam systems have the lowest peak demand but do not reduce energy consumption significantly because the reduction in fan energy is offse t by a reduction in air-side free cooling. Overall, the results indicate significant opportunities for LEC technologies to reduce energy consumption and demand in nonresidential new construction and retrofit.

This report outlines U.S. military operations in Bosnia and discusses issues such as U.S. and Allied Participation in Bosnia Peacekeeping (IFOR/SFOR), duration, cost, arms control and military assistance. This report also includes most recent development, background analysis, and legislation.