The objective of this study was to examine the relative importance of pressure changes as a source of turbine-passage injury and mortality. Specific tests were designed to quantify the response of fish to rapid pressure changes typical of turbine passage, with and without the complication of the fish being acclimated to gas supersaturated water. We investigated the responses of rainbow trout (Oncorhynchus mykiss), chinook salmon (O. tshawytscha), and bluegill sunfish (Lepomis macrochirus) to these two stresses, both singly and in combination.

This Annual Report provides an overview of the FY2000 Laboratory Directed Research and Development (LDRD) Program at Lawrence Livermore National Laboratory (LLNL) and presents a summary of the results achieved by each project during the year.

This report documents the process used by the Tanks Focus Area (TFA) to analyze and develop responses to technology needs submitted by five major U.S. Department of Energy (DOE) sites with radioactive tank waste problems, and the initial results of the analysis. The sites are the Hanford Site, Idaho National Engineering and Environmental Laboratory (INEEL), Oak Ridge Reservation (ORR), Savannah River Site (SRS), and West Valley Demonstration Project (WVDP). During the past year, the TFA established a link with DOE's Fernald site to exchange, on a continuing basis, mutually beneficial technical information and assistance.

This document summarizes the Tanks Focus Area (TFA's) process of collecting, analyzing, and responding to high-level radioactive tank waste science and technology needs developed from across the DOE complex in FY 2000. The document also summarizes each science and technology need, and provides an initial prioritization of TFA's projected work scope for FY 2001 and FY 2002.

This report is one of two that re-examines the forecasted impact of individual programs currently within the Buildings Technology Program (BT) and the Weatherization and Intergovernmental Program (WIP) that appeared in the FY2000 Presidential Budget request. This report develops potential methods for allowing inherent risk to be captured in the program benefits analysis. Note that the FY2000 budget request was originally analyzed under the former Office of Building Technology, State and Community Programs (BTS), where BT and WIP were previously combined. Throughout the document, reference will be made to the predecessor of the BT and WIP programs, BTS, as FY2000 reflected that organization. A companion report outlines the effects of re-estimating the FY 2000 budget request based on overlaying program data from subsequent years, essentially revised out-year forecasts. That report shows that year-to-year long-term projections of primary energy savings can vary widely as models improve and programs change. Those point estimates are not influenced by uncertainty or risk. This report develops potential methods for allowing inherent risk to affect the benefits analysis via Monte Carlo simulation.

Most large-scale high-critical-temperature superconductor applications require wires or tapes that an carry high currents in applied magnetic fields. This report describes technical progress of research and development efforts aimed at producing superconducting components and devices in the Y-Ba-Cu-O and Bi-(Pb)-Sr-Ca-Cu-O systems. Topics discussed are formation of first- and second-generation composite conductors, characterization of structures and superconducting and mechanical properties, modeling of grain-boundary current transport, and fabrication and analysis of prototype components.

Palladium used at Savannah River (SR) for process tritium storage is currently obtained from a commercial source. In order to understand the processes involved in preparing this material, SR is supporting investigations into the chemical reactions used to synthesize this material. The material specifications are shown in Table 1. An improved understanding of the chemical processes should help to guarantee a continued reliable source of Pd in the future. As part of this evaluation, a work-for-others contract between Westinghouse Savannah River Company and Ames Laboratory (AL) was initiated. During FY98, the process for producing Pd powder developed in 1986 by Dan Grove of Mound Applied Technologies, USDOE (the Mound muddy water process) was studied to understand the processing conditions that lead to changes in morphology in the final product. During FY99 and FY00, the process for producing Pd powder that has been used previously at Sandia and Los Alamos National Laboratories (the Sandia/LANL process) was studied to understand the processing conditions that lead to changes in the morphology of the final Pd product. During FY01, scale-up of the process to batch sizes greater than 600 grams of Pd using a 20-gallon Pfaudler reactor was conducted by the Iowa State University …

The Hanford Site 200 Area Effluent Treatment Facility (ETF) processes contaminated liquids derived from Hanford Site facilities. Groundwater monitoring for tritium and other constituents is required by the state-issued permit at 22 wells surrounding the facility. Water level measurements in nearby wells indicate that a small hydraulic mound exists around the SALDS facility as a result of discharges. Evaluation of this condition indicates that the network is currently adequate for tracking potential effects of the SALDS on the groundwater. During FY 2000, average tritium activities in most wells declined from average activities in 1999. The exception was deep well 699-48-77C, where tritium results were at an all-time high (710,000 pCi/L) as a result of the delayed penetration of effluent deeper into the aquifer. Of the 12 constituents with permit enforcement limits, which are monitored in SALDS proximal wells, all were within groundwater limitations during FY 2000. Analyses for conductivity, total dissolved solids, sulfate, chloride, sulfate, dissolved calcium, and dissolved sodium indicate that well 699-48-77A and, to a lesser extent, well 699-48-77D show the effects of dilute effluent entering groundwater, resulting in a depression of concentrations of these constituents below natural background levels. Recommendations for future monitoring include temporarily increasing the …

In FY-2000, Engineering at Lawrence Livermore National Laboratory faced significant pressures to meet critical project milestones, and immediate demands to facilitate the reassignment of employees as the National Ignition Facility (the 600-TW laser facility being designed and built at Livermore, and one of the largest R&D construction projects in the world) was in the process of re-baselining its plan while executing full-speed its technology development efforts. This drive for change occurred as an unprecedented level of management and program changes were occurring within LLNL. I am pleased to report that we met many key milestones and achieved numerous technological breakthroughs. This report summarizes our efforts to perform feasibility and reduce-to-practice studies, demonstrations, and/or techniques--as structured through our technology centers. Whether using computational engineering to predict how giant structures like suspension bridges will respond to massive earthquakes or devising a suitcase-sized microtool to detect chemical and biological agents used by terrorists, we have made solid technical progress. Five Centers focus and guide longer-term investments within Engineering, as well as impact all of LLNL. Each Center is responsible for the vitality and growth of the core technologies it represents. My goal is that each Center will be recognized on an international scale …

The fabrication of boron-covered crystal scintillation detectors is described. Bulk boron-loaded epoxy material was cast and cut into 0.5 mm-thick wafers that were mounted on CdWO{sub 4} and CsI(Tl) crystals. The crystals were mounted on miniature photomultiplier tubes and gamma spectra were obtained with the detectors. The ability of these small detectors to produce spectra that can be analyzed to provide isotopic identification has been demonstrated. In addition, the detector can produce a signature indicating the presence of neutrons. The same miniature size of these detectors that makes them attractive for hand-held portable use, may be a limiting factor in their efficiency. The small size of the scintillation crystals makes them not as efficient as larger NaI(Tl) crystals simply by virtue of significantly decreased sensitive volume and surface area. It may be worthwhile to consider slightly larger crystals (approximately 15 mm cubic CdWO{sub 4}) mounted on rectangular photomultipliers in a detecting head connected to the electronics package by a signal cable.

The fabrication of boron-covered crystal scintillation detectors is described. Bulk boron-loaded epoxy material was cast and cut into 0.5 mm-thick wafers that were mounted on CdWO{sub 4} and CsI(Tl) crystals. The crystals were mounted on miniature photomultiplier tubes and gamma spectra were obtained with the detectors. The ability of these small detectors to produce spectra that can be analyzed to provide isotopic identification has been demonstrated. In addition, the detector can produce a signature indicating the presence of neutrons. The same miniature size of these detectors that makes them attractive for hand-held portable use, may be a limiting factor in their efficiency. The small size of the scintillation crystals makes them not as efficient as larger NaI(Tl) crystals simply by virtue of significantly decreased sensitive volume and surface area. It may be worthwhile to consider slightly larger crystals (approximately 15 mm cubic CdWO{sub 4}) mounted on rectangular photomultipliers in a detecting head connected to the electronics package by a signal cable.

Our goal is to improve geophysical imaging of the vadose zone. We will achieve this goal by providing new methods to improve interpretation of field data. The purpose of this EMSP project is to develop relationships between laboratory measured geophysical properties and porosity, saturation, and fluid distribution, for partially saturated soils. Algorithms for relationships between soil composition, saturation, and geophysical measurements will provide new methods to interpret geophysical field data collected in the vadose zone at sites such as Hanford, WA. This report summarizes work after 10 months of a 3-year project. We have modified a laboratory ultrasonics apparatus developed in a previous EMSP project (No.55411) so that we can make velocity measurements for partially-saturated samples rather than fully-saturated or dry samples. We are testing the measurement apparatus using standard laboratory sand samples such as Ottawa sand samples. Preliminary results indicate that we can measure both compressional and shear velocities in these sand samples. We have received Hanford soil samples (sands from split-spoon cores from an uncontaminated site) and expect to make ultrasonic measurements on them also. We have used the LLNL x-ray facility to perform x-ray computed tomography (XCT) imaging for several partially-saturated Ottawa sand and Lincoln sand samples, …

We have begun building the ''Mercury'' laser system as the first in a series of new generation diode-pumped solid-state lasers for target physics research. Mercury will integrate three key technologies: diodes, crystals, and gas cooling, within a unique laser architecture that is scalable to kilojoule and megajoule energy levels for fusion energy applications. The primary near-term performance goals include 10% electrical efficiencies at 10 Hz and 100 J with a 2-10 ns pulse length at 1.047 {micro}m wavelength. Currently, this review concentrates on the critical development and production of Yb:S-FAP crystals. After solving many defect issues that can be present in the crystals, reproducibility is the final issue that needs to be resolved. We have enlisted the help of national experts and have strongly integrated two capable commercial crystal growth companies (Litton-Airton/Synoptics and Scientific Materials) into the effort, and have solicited the advice of Robert Morris (retired from Allied Signal), a recognized international expert in high temperature oxide growth.

This report summarizes the objectives, tasks, and accomplishments of the Tucannon River spring chinook captive brood program from program inception (1997) through April 2001. The WDFW initiated a captive broodstock program in 1997. The overall goal of the Tucannon River captive broodstock program is for the short-term, and eventually long-term, rebuilding of the Tucannon River spring chinook salmon run, with the hope that natural production will eventually sustain itself. The project goal is to rear captive salmon to adults, spawn them, rear their progeny, and release approximately 150,000 smolts annually into the Tucannon River between 2003-2007. These smolt releases, in combination with the current hatchery supplementation program (132,000 smolts), and wild production, is expected to produce 600-700 returning adult spring chinook to the Tucannon River each year from 2005-2010. The Master Plan, Environmental Assessment, and most facility modifications at LFH were completed for the Tucannon River spring chinook captive broodstock program during FY2000 and FY2001. DNA samples collected since 1997 have been sent to the WDFW genetics lab in Olympia for baseline DNA analysis. Results from the genetic analysis are not available at this time. The captive broodstock program is planned to collect fish from five (1997-2001) brood years (BY). …

The Moses Lake Project (project No. 199502800) was first funded during FY 99 and field studies commenced October 2000. Later review of the proposal by the ISRP revealed perceived shortcomings. Immediately following the ISRP review Washington Department of Fish and Wildlife (WDFW) personnel were in contact with the Northwest Power Planning Council (NWPPC) regarding further options. The NWPPC allowed WDFW to re-submit the first proposal revision that was followed in June 2001 by a second negative review by the ISRP. In August 2001, the NWPPC authorized a third and final submission of the proposal and limited funding extension. Therefore, proposal revisions and resubmissions limited progress in data collection and analysis. This report covers work conducted within the submitted scope of work (FY 2000, September 27, 2000--September 26, 2001) and incorporation of the suggested modifications to the proposal. The bulk of the work covered by this report concentrated on data collection.

The Pine Hollow Project (1999-010-00) is an on-going watershed restoration effort administered by Sherman County Soil and Water Conservation District and spearheaded by Pine Hollow/Jackknife Watershed Council. The headwaters are located near Shaniko in Wasco County, and the mouth is in Sherman County on the John Day River. Pine Hollow provides more than 20 miles of potential summer steelhead spawning and rearing habitat. The watershed is 92,000 acres. Land use is mostly range, with some dryland grain. There are no water rights on Pine Hollow. Due to shallow soils, the watershed is prone to rapid runoff events which scour out the streambed and the riparian vegetation. This project seeks to improve the quality of upland, riparian and in-stream habitat by restoring the natural hydrologic function of the entire watershed. Project implementation to date has consisted of construction of water/sediment control basins, gradient terraces on croplands, pasture cross-fences, upland water sources, and grass seeding on degraded sites, many of which were crop fields in the early part of the century. The project is expected to continue through about 2007. From March 2000 to June 2001, the Pine Hollow Project built 6 sediment basins, 1 cross-fence, 2 spring developments, 1 well development, …

Advances in Artificial Intelligence (AI) and micro-technologies will soon give rise to production of large-scale forces of autonomous micro-robots with systems of innate behaviors and with capabilities of self-organization and real world tasking. Such organizations have been compared to schools of fish, flocks of birds, herds of animals, swarms of insects, and military squadrons. While these systems are envisioned as maintaining a high degree of autonomy, it is important to understand the relationship of man with such machines. In moving from research studies to the practical deployment of large-scale numbers of robots, one of critical pieces that must be explored is the command and control architecture for humans to re-task and also inject global knowledge, experience, and intuition into the force. Tele-operation should not be the goal, but rather a level of adjustable autonomy and high-level control. If a herd of sheep is comparable to the collective of robots, then the human element is comparable to the shepherd pulling in strays and guiding the herd in the direction of greener pastures. This report addresses the issues and development of command and control for largescale numbers of autonomous robots deployed as a collective force.

None

OAK B188 FINAL REPORT OF FY 1999, 2000, AND 2001 ACTIVITIES: CONTINUED DEVELOPMENT OF AN INTEGRATED SOUNDING SYSTEM IN SUPPORT OF THE DOE/ARM EXPERIMENTAL PROGRAM The basic goals of the research are to develop and test algorithms and deploy instruments that improve measurements of atmospheric quantities relevant to radiative transfer and climate research. Primary among these atmospheric variables are integrated amounts of water vapor and cloud liquid, as well as profiles of temperature, water vapor and cloud liquid. A primary thrust of this research is to combine data from instruments available to ARM to maximize their importance in radiative transfer and climate research. To gather data relevant to these studies, participation in field experiments, especially intensive operating periods, as well as the subsequent analysis and dissemination of collected data, is of primary importance. Examples of relevant experiments include several Water Vapor Intensive Operating Periods at the Southern Great Plains Cloud And Radiation Testbed site, experiments in the Tropical Western Pacific such as PROBE and Nauru'99, and experiments at the North Slope of Alaska/Adjacent Arctic Ocean site. This final report describes our analyses of data taken during these field experiments.

A major milestone was reached in Fiscal Year (FY) 2000--the completion of the Chicago Pile-5 (CP-5) D and D Project. CP-5, the first reactor built on the Argonne National Laboratory-East (ANL-E) site, was a 5-megawatt, heavy water-moderated, enriched uranium-fueled reactor. It was the principal reactor on the Argonne site used to produce neutrons for scientific research from 1954 to 1979. The reactor was shut down and defueled in 1979, and placed in a lay-up condition. In 1990, funding was provided to begin the decontamination and decommissioning (D and D) of this facility, and work began in June 1991. D and D tasks were performed by both ANL-E personnel and subcontractor personnel from Duke Engineering and Services, Marlborough MA, under the management of ANL-E D and D Program personnel. In July 2000, the final project report was presented to the Department of Energy, and the facility was formally decommissioned and transferred to the landlord. Total project duration was 97 months, and total project cost was $29.5M. Also, in FY 2000, work began on the 60 Cyclotron D and D Project. An accelerator used for basic research, this facility produced beams of deuterons, helium ions, singly charged hydrogen molecules, and neutrons of …

This document describes the baseline single-shell tank (SST) waste retrieval sequence for the River Protection Project (RPP) updated for Fiscal Year 2000. The SST retrieval sequence identifies the proposed retrieval order (sequence), the tank selection and prioritization rationale, and planned retrieval dates for Hanford SSTs. In addition, the tank selection criteria and reference retrieval method for this sequence are discussed.

This report summarizes the activities of the Analytical Chemistry Laboratory (ACL) at Argonne National Laboratory (ANL) for Fiscal Year (FY) 2000 (October 1999 through September 2000). This annual progress report, which is the seventeenth in this series for the ACL, describes effort on continuing projects, work on new projects, and contributions of the ACL staff to various programs at ANL. The ACL operates within the ANL system as a full-cost-recovery service center, but it has a mission that includes a complementary research and development component: The Analytical Chemistry Laboratory will provide high-quality, cost-effective chemical analysis and related technical support to solve research problems of our clients--Argonne National Laboratory, the Department of Energy, and others--and will conduct world-class research and development in analytical chemistry and its applications. The ACL handles a wide range of analytical problems that reflects the diversity of research and development (R&D) work at ANL. Some routine or standard analyses are done, but the ACL operates more typically in a problem-solving mode in which development of methods is required or adaptation of techniques is needed to obtain useful analytical data. The ACL works with clients and commercial laboratories if a large number of routine analyses are required. Much …

Laboratory tests were completed on the dissolution characteristics of Hanford saltcake waste from single-shell waste tanks 241-TX- 113, 241-BY-102, 241-BY-106, 241-A-101, and 241-S-102 (henceforth referred to as TX-113, BY-102, BY-106, A-101, and S-102, respectively). This work was funded by the Tanks Focus Area (EM-50) under Technical Task Plan Number RL0-8-WT-41, ''PHMC Pretreatment--Saltcake Dissolution''. The tests performed on saltcake from tank TX-113 were similar in scope to those completed in previous years on waste from tanks BY-102, BY-106, B-106, A-101, and S-102 (Herting 1998, 1999). In addition to the ''standard'' dissolution tests, new types of tests were performed this year related to feed stability and radionuclide distribution. The River Protection Project (RPP) is tasked with retrieving waste from double-shell and single-shell tanks to provide feed for vitrification. The RPP organization needs chemical and physical data to evaluate technologies for retrieving the waste. Little significant laboratory testing has been done to evaluate in-tank dissolution parameters for the various types of saltcake wastes that exist in single-shell tanks. A computer modeling program known as the Environmental Simulation Program (ESP), produced by OLI Systems, Inc of Morris Plains, New Jersey, is being used by the RPP organization to predict solubilities during dilution and retrieval …

The Ernest Orlando Lawrence Berkeley National Laboratory (Berkeley Lab or LBNL) is a multi-program national research facility operated by the University of California for the Department of Energy (DOE). As an integral element of DOE's National Laboratory System, Berkeley Lab supports DOE's missions in fundamental science, energy resources, and environmental quality. Berkeley Lab programs advance four distinct goals for DOE and the nation: (1) To perform leading multidisciplinary research in the computing sciences, physical sciences, energy sciences, biosciences, and general sciences in a manner that ensures employee and public safety and protection of the environment. (2) To develop and operate unique national experimental facilities for qualified investigators. (3) To educate and train future generations of scientists and engineers to promote national science and education goals. (4) To transfer knowledge and technological innovations and to foster productive relationships among Berkeley Lab's research programs, universities, and industry in order to promote national economic competitiveness. Annual report on Laboratory Directed Research and Development for FY2000.