A hydrogen safety sensor is presented which provides high sensitivity and fast response time when operated in air. The target application for the sensor is external deployment near systems using or producing high concentrations of hydrogen. The sensor is composed of a catalytically active metal-oxide sensing electrode and a noble metal reference electrode attached to an yttria-stabilized zirconia (YSZ) electrolyte. The sensing approach is based on the difference in oxidation rate of hydrogen on the different electrode materials. Results will be presented for a sensor using a sensing electrode of tin-doped indium oxide (ITO). Response to H{sub 2}, and cross-sensitivity to hydrocarbon and H{sub 2}O are discussed.

The objective of this spent fuel burnup credit work was to study and describe a VVER-440 reactor spent fuel assembly (FA) initial state before irradiation, its operational irradiation history and the resulting radionuclide distribution in the fuel assembly after irradiation. This work includes the following stages: (1) to pick out and select a specific spent (irradiated) FA for examination; (2) to describe the FA initial state before irradiation; (3) to describe the irradiation history, including thermal calculations; (4) to examine the burnup distribution of select radionuclides along the FA height and cross-section; (5) to examine the radionuclide distributions; (6) to determine the Kr-85 release into the plenum; (7) to select and prepare FA rod specimens for destructive examinations; (8) to determine the radionuclide compositions, isotope masses and burnup in the rod specimens; and (9) to analyze, document and process the results. The specific workscope included the destructive assay (DA) of spent fuel assembly rod segments with an {approx}38.5 MWd/KgU burnup from a single VVER-440 fuel assembly from the Novovorenezh reactor in Russia. Based on irradiation history criteria, four rods from the fuel assembly were selected and removed from the assembly for examination. Next, 8 sections were cut from the four …

One new groundwater monitoring well was constructed at the 200-ZP-1 Operable Unit in November 2002. This document provides the information on drilling and construction of this well. One new groundwater monitoring well was constructed in the 200-ZP-1 Operable Unit in November 2002. The purpose of the well is to monitor carbon tetrachloride concentrations in response to the 200-ZP-1 carbon tetrachloride pump-and-treat operations. The well name is 299-W15-43 and the corresponding well number is C3955. Well 299-W15-43 is located about 8 meters west of the 216-T-25 trench. The location of the well is shown on Figure 1. Well 299-W15-43 was drilled in response to the recommendations of a Data Quality Objectives process that indicated a need for additional monitoring wells in the area (BHI-01576). The new well was constructed to the specifications and requirements described in Washington Administrative Code (WAC) 173-160 and WAC 173-303, the Data Quality Objectives document (BHI-01576), and the description of work for well drilling and construction. This document compiles information on the drilling and construction, geophysical logging, and sediment and groundwater sampling applicable to the installation of well 299-W15-43. The information on drilling and construction, well development, and pump installation is summarized from CP-14265. Appendix A contains …

Diabetes is a disease that affects over 16 million people in the USA at a cost of 100 billion dollars annually. The ability to regulate insulin delivery in people with Type 1 diabetes is imperative as is the need to manage glucose levels in all people with this disease. Our current method for monitoring glucose is a (FDA approved) minimally invasive enzymatic sensor that can measure glucose levels in vivo for three days. We are focused on developing a noninvasive implantable glucose sensor that will be interrogated by an external device. The material must be robust, easy to process, biocompatible and resistant to biofouling. In this Presentation we will discuss the development of a new polymeric matrix that can recognize physiological levels of glucose in vitro using fluorescent spectroscopy.

Restricted availability of funding has had an adverse impact, unforeseen at the time of the original decision to projectize the National Ignition Facility (NIF) Cryogenic Target Handling Systems (NCTS) Program, on the planning and initiation of these efforts. The purpose of this document is to provide an interim project management plan describing the organizational structure and management processes currently in place for NCTS. Preparation of a Program Execution Plan (PEP) for NCTS has been initiated, and a current draft is provided as Attachment 1 to this document. The National Ignition Facility is a multi-megajoule laser facility being constructed at Lawrence Livermore National Laboratory (LLNL) by the National Nuclear Security Administration (NNSA) in the Department of Energy (DOE). Its primary mission is to support the Stockpile Stewardship Program (SSP) by performing experiments studying weapons physics, including fusion ignition. NIF also supports the missions of weapons effects, inertial fusion energy, and basic science in high-energy-density physics. NIF will be operated by LLNL under contract to the University of California (UC) as a national user facility. NIF is a low-hazard, radiological facility, and its operation will meet all applicable federal, state, and local Environmental Safety & Health (ES&H) requirements. The NCTS Interim Management …

We consider the collinear limit of QCD amplitudes at one-loop order, and their factorization properties directly in color space. These results apply to the multiple collinear limit of an arbitrary number of QCD partons, and are a basic ingredient in many higher-order computations. In particular, we discuss the triple collinear limit and its relation to flavor asymmetries in the QCD evolution of parton densities at three loops. As a phenomenological consequence of this new effect, and of the fact that the nucleon has non-vanishing quark valence densities, we study the perturbative generation of a strange-antistrange asymmetry s(x)-{bar s}(x) in the nucleon's sea.

The National Ignition Facility (NIF) has the mission of supporting Stockpile Stewardship and Basic Science research in high-energy-density plasmas. To execute those missions, the facility must provide diagnostic instrumentation capable of observing and resolving in time events and radiation emissions characteristic of the plasmas of interest. The diagnostic instrumentation must conform to high standards of operability and reliability within the NIF environment. These exacting standards, together with the facility mission of supporting a diverse user base, has led to the need for a central organization charged with delivering diagnostic capability to the NIF. The National NIF Diagnostics Program (NNDP) has been set up under the aegis of the NIF Director to provide that organization authority and accountability to the wide user community for NIF. The funds necessary to perform the work of developing diagnostics for NIF will be allocated from the National NIF Diagnostics Program to the participating laboratories and organizations. The participating laboratories and organizations will design, build, and commission the diagnostics for NIF. Restricted availability of funding has had an adverse impact, unforeseen at the time of the original decision to projectize NIF Core Diagnostics Systems and Cryogenic Target Handing Systems, on the planning and initiation of these …

HYSPEC is a direct geometry spectrometer to be installed at the SNS [1] on beamline 14B where it will view a cryogenic coupled hydrogen moderator, The ''hybrid'' design combines time-of-flight spectroscopy with focusing Bragg optics to provide a high monochromatic flux on small single crystal samples, with a very low background at an extended detector bank. The instrument is optimized for an incident energy range of 3-90meV. It will have a medium energy resolution (2-10%) and will provide a flux on sample of the order of 10{sup 6}-10{sup 7} neutrons/s-cm{sup 2}. The spectrometer will be located in a satellite building outside the SNS experimental hall at the end of a 35m curved supermirror guide. A straight-slotted Fermi chopper will be used to monochromate the neutron beam and to determine the burst width. The 15cm high, 4cm wide beam will be focused onto a 2cm by 2cm area at the sample position using Bragg reflection from one of two crystal arrays. For unpolarized neutron studies these will be Highly Oriented Pyrolitic graphite crystals while for polarized neutron studies these will be replaced with Heusler alloy crystals. These focusing crystal arrays will be placed in a drum shield similar to those used …

The Hybrid Spectrometer (HYSPEC), under construction at the SNS on beam line 14B, is the only inelastic scattering instrument designed to enable polarization of the incident and the scattered neutron beams. A Heusler monochromator will replace the graphite crystal for producing polarized neutrons. In the scattered beam it is planned to use a collimator--multi-channel supermirror bender array to analyze the polarization of the scattered beam over the final energy range from 5-20 meV. Other methods of polarization analysis under consideration such as transmission filters using He{sup 3}, Sm, and polarized protons are considered. Their performance is estimated and a comparison of the various methods of polarization is made.

Electrical conductivities of fluid oxygen were measured between 30 and 80 GPa at a few 1000 K. These conditions were achieved with a reverberating shock wave technique. The measured conductivities were several orders of magnitude lower than measured previously on the single shock Hugoniot because of lower temperatures achieved under shock reverberation. Extrapolation of these data suggests that the minimum metallic conductivity of a metal will be reached near 100 GPa.

X-ray free-electron lasers will produce pulses of x-rays that are 10 orders of magnitude brighter than today's undulator sources at synchrotrons. This may enable atomic resolution imaging of single macromolecules.

The current OSP associated with Room 1711A located in Building 191 (HEAF) sets a limit of 5 grams Net Explosive Weight (NEW) of explosives for the room. A question was raised as to the capability of that room to withstand the overpressure created by a detonation of 5 grams NEW of explosives. Calculations were inconclusive, but indicated the wallboard would not remain intact if there was a detonation of 5 grams NEW at a distance of eight feet from the wall. These calculations did not seem logical. To verify the hypothesis, a series of experiments were conducted in the 1 Kilogram tank. The experiments consisted of exposing a pre-built double-sided wall with the same stud spacing and drywall thickness found in the walls of Room 1711A to various amounts of explosives to create expected overpressures. The objective of this test was to prove or disprove that the walls in room 1711A could withstand a detonation of 5 grams of high explosives and to determine if larger quantities of explosives could be worked on in the room while still providing the required level of protection for personnel outside the room. Testing has verified that not only can the walls withstand a …

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package TransporterModel II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: "each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application." They further state: "each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application." Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant| (WIPP) management and operating (M&O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code …

The Energy Policy and Conservation Act (EPCA) as amended by the Energy Policy Act of 1992 (EPACT) establishes that the U.S. Department of Energy (DOE) regulate efficiency levels of certain categories of commercial heating, cooling, and water-heating equip-ment. EPACT establishes the initial minimum efficiency levels for products falling under these categories, based on ASHRAE/IES Standard 90.1-1989 requirements. EPCA states that, if ASHRAE amends Standard 90.1-1989 efficiency levels, then DOE must establish an amended uniform national manufacturing standard at the minimum level specified in the amended Standard 90.1 and that it can establish higher efficiency levels if they would result in significant additional energy savings. Standard 90.1-1999 increases minimum efficiency levels for some of the equipment categories covered by EPCA 92. DOE conducted a screening analysis to determine the energy-savings potential for EPACT-covered products meet and exceeding these levels. This paper describes the methodology, data assumptions, and results of the analysis.

In 2003, Engelhard Corporation received a DOE award to develop a cost-effective, environmentally friendly approach to recover Pt from fuel cell membrane electrode assemblies (MEA’s). The most important precious metal used in fuel cells is platinum, but ruthenium is also added to the anode electrocatalyst if CO is present in the hydrogen stream. As part of the project, a large number of measurements of Pt and Ru need to be made. A low-cost approach to measuring Pt is using the industry standard spectrophotometric measurement of Pt complexed with stannous chloride. The interference of Ru can be eliminated by reading the Pt absorbance at 450 nm. Spectrophotometric methods for measuring Ru, while reported in the literature, are not as robust. This paper will discuss the options for measuring Pt and Ru using the method of UV-VIS spectrophotometry

Ovarian epithelial carcinomas (OEC) frequently exhibit amplifications at the 20q13 locus which is the site of several oncogenes, including the eukaryotic elongation factor EEF1A2 and the transcription factor ZNF217. We reported previously that overexpressed ZNF217 induces neoplastic characteristics in precursor cells of OEC. Unexpectedly, ZNF217, which is a transcriptional repressor, enhanced expression of eEF1A2. In this study, array comparative genomic hybridization, single nucleotide polymorphism and Affymetrix analysis of ZNF217-overexpressing cell lines confirmed consistently increased expression of eEF1A2 but not of other oncogenes, and revealed early changes in EEF1A2 gene copy numbers and increased expression at crisis during immortalization. We defined the influence of eEF1A2 overexpression on immortalized ovarian surface epithelial cells, and investigated interrelationships between effects of ZNF217 and eEF1A2 on cellular phenotypes. Lentivirally induced eEF1A2 overexpression caused delayed crisis, apoptosis resistance and increases in serum-independence, saturation densities, and anchorage independence. siRNA to eEF1A2 reversed apoptosis resistance and reduced anchorage independence in eEF1A2-overexpressing lines. Remarkably, siRNA to eEF1A2 was equally efficient in inhibiting both anchorage independence and resistance to apoptosis conferred by ZNF217 overexpression. Our data define neoplastic properties that are caused by eEF1A2 in nontumorigenic ovarian cancer precursor cells, and suggest that eEF1A2 plays a role in mediating ZNF217-induced …

Transitory starch builds up in photosynthesizing leaves during the day and is then degraded each night. It has recently been shown through mutant analysis and genetically engineered plants that transitory starch is required for maximal rates of photosynthesis, especially in high carbon dioxide atmospheres. Understanding the pathway by which carbon is exported from chloroplasts at night is limited. Previous work has shown that starch conversion to sucrose at night involves maltose export from chloroplasts. This pathway for carbon export from chloroplasts normally does not occur during the day. The regulation of maltose formation, the transporters that allow export of maltose from the chloroplast, and the cytosolic reactions by which maltose is converted to sucrose remain obscure. Genomic and biochemical approaches are proposed here to address maltose metabolism and transport. The research will cover three areas (1) how are hydrolytic and phosphorylytic starch degradation regulated, (2) how is maltose exported from chloroplasts, and (3) how is maltose converted to sucrose in the cytosol? It is expected that this research will lead to new insights about photosynthesis at high carbon dioxide levels, how carbon is partitioned in plants, and how partitioning can be altered to adapt plants to human needs.

The Stockpile Stewardship Program (SSP) is a single, highly integrated technical program for maintaining the safety and reliability of the U.S. nuclear stockpile. The SSP uses past nuclear test data along with current and future nonnuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of current facilities and programs along with new experimental facilities and computational enhancements to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities and computational resources to support the annual stockpile assessment and certification, to study advanced nuclear-weapons design and manufacturing processes, to analyze accident scenarios and weapons aging, and to provide the tools to enable Stockpile Life Extension Programs (SLEPs) and the resolution of Significant Finding Investigations (SFIs). This requires a balanced resource, including technical staff, hardware, simulation software, and computer science solutions. In its first decade, the ASC strategy focused on demonstrating simulation capabilities of unprecedented scale in three spatial dimensions. In its second decade, ASC is focused on …

Geothermal exploration and subsequent characterization of potential resources typically employ a variety of geophysical, geologic and geochemical techniques. However, since the data collected by each technique provide information directly on only one or a very limited set of the many physical parameters that characterize a geothermal system, no single method can be used to describe the system in its entirety. Presently, the usual approach to analyzing disparate data streams for geothermal applications is to invert (or forward model) each data set separately and then combine or compare the resulting models, for the most part in a more or less ad hoc manner. However, while each inversion may yield a model that fits the individual data set, the models are usually inconsistent with each other to some degree. This reflects uncertainties arising from the inevitable fact that geophysical and other exploration data in general are to some extent noisy, incomplete, and of limited sensitivity and resolution, and so yield non-unique results. The purpose of the project described here is to integrate the different model constraints provided by disparate geophysical, geological and geochemical data in a rigorous and consistent manner by formal joint inversion. The objective is to improve the fidelity of …

Protocols for monitoring salmon habitat restoration projects are essential for the U.S. Army Corps of Engineers' environmental efforts in the Columbia River estuary. This manual provides state-of-the science data collection and analysis methods for landscape features, water quality, and fish species composition, among others.

In complying with direction from the U.S. Department of Energy (DOE), Richland Operations Office (RL) (07-KBC-0055, 'Direction Associated with Implementation of DOE-STD-1189 for the Sludge Treatment Project,' and 08-SED-0063, 'RL Action on the Safety Design Strategy (SDS) for Obtaining Additional Solid Waste Processing Capabilities (M-91 Project) and Use of Draft DOE-STD-I 189-YR'), it has been determined that the seismic design requirements currently in the Project Hanford Management Contract (PHMC) will be modified by DOE-STD-1189, Integration of Safety into the Design Process (March 2007 draft), for these two key PHMC projects. Seismic design requirements for other PHMC facilities and projects will remain unchanged. Considering the current early Critical Decision (CD) phases of both the Sludge Treatment Project (STP) and the Solid Waste Processing Facilities (M-91) Project and a strong intent to avoid potentially costly re-work of both engineering and nuclear safety analyses, this document describes how Fluor Hanford, Inc. (FH) will maintain compliance with the PHMC by considering both the current seismic standards referenced by DOE 0 420.1 B, Facility Safety, and draft DOE-STD-1189 (i.e., ASCE/SEI 43-05, Seismic Design Criteria for Structures, Systems, and Components in Nuclear Facilities, and ANSI!ANS 2.26-2004, Categorization of Nuclear Facility Structures, Systems and Components for Seismic …

We describe the design and operation of a high-throughput facility for synthesizing thousands of inorganic crystalline samples per year and evaluating them as potential scintillation detector materials. This facility includes a robotic dispenser, arrays of automated furnaces, a dual-beam X-ray generator for diffractometery and luminescence spectroscopy, a pulsed X-ray generator for time response measurements, computer-controlled sample changers, an optical spectrometer, and a network-accessible database management system that captures all synthesis and measurement data.

The response of a recently acquired Canberra{trademark} Alpha Analyst 'Blue' system (Chamber Number's 173-208) used by the Hazards Control, Radiation Safety Section, WBC/Spectroscopy Team has been studied with respect to an existing Canberra system. The existing Canberra system consists of thirty Alpha Analyst dual chambers Model XXXX comprising a total of sixty detectors (Chambers Number's 101-124 and 137-172). The existing chambers were previously compared to an older system consisting of thirty-six Model 7401 alpha spectrometry chambers (Chamber Number's 1-36) Chambers 101-124 and 137-172 are DOELAP accredited. The older system was previously DOELAP accredited for the routine Alpha Spectroscopy program used in LLNL's in vitro bioassay program. The newly acquired Alpha Analyst system operates on a network with software that controls and performs analysis of the current Alpha Analyst system (Chamber Number's 101-124 and 137-172). This exact same software is used for the current system and the newly acquired system and is DOELAP accredited. This document compares results from the existing Alpha System with the newer Alpha Analyst system.

A process to facilitate mercury extraction from high temperature flue/fuel gas via the use of metal sorbents which capture mercury at ambient and high temperatures. The spent sorbents can be regenerated after exposure to mercury. The metal sorbents can be used as pure metals (or combinations of metals) or dispersed on an inert support to increase surface area per gram of metal sorbent. Iridium and ruthenium are effective for mercury removal from flue and smelter gases. Palladium and platinum are effective for mercury removal from fuel gas (syngas). An iridium-platinum alloy is suitable for metal capture in many industrial effluent gas streams including highly corrosive gas streams.