The ternary semiconductor GaAs{sub 1{minus}x}N{sub x} with 0 < x < 0.3 can be grown epitaxially on GaAs and has a very large bowing coefficient. The alloy bandgap can be reduced to about 1.0 eV with about a 3% nitrogen addition. In this work, the authors measured the internal spectral response and recombination lifetime of a number of alloys using the ultra-high frequency photoconductive decay (UHFPCD) method. The data shows that the photoconductive excitation spectra of the GaAs{sub 0.97}N{sub 0.03} alloy shows a gradual increase in response through the absorption edge near E{sub g}. This contrasts with most direct bandgap semiconductors that show a steep onset of photoresponse at E{sub g}. The recombination lifetimes frequently are much longer than expected from radiative recombination and often exceeded 1.0{mu}s. The data were analyzed in terms of a band model that includes large potential fluctuations in the conduction band due to the random distribution of nitrogen atoms in the alloy.

Today's restrictive environmental regulations encourage paper mills to close their water systems. Closed water systems increase the level of contaminants significantly. Accumulations of solid suspensions are detrimental to both the papermaking process and the final products. To remove these solids, technologies such as flotation using dissolved air (DAF), centrifuging, and screening have been developed. Dissolved Air Flotation systems are commonly used to clarify whitewater. These passive systems use high pressure to dissolve air into whitewater. When the pressure is released, air micro-bubbles form and attach themselves to fibers and particles, which then float to the surface where they are mechanically skimmed off. There is an economic incentive to explore alternatives to the DAF technology to drive down the cost of whitewater processing and minimize the use of chemicals. The installed capital cost for a DAF system is significant and a typical DAF system takes up considerable space. An alternative approach, which is the subject of this project, involves a dual method combining the advantages of chemical flocculation and in-line ultrasonic clarification to efficiently remove flocculated contaminants from a water stream

In many urban areas, pavements and roofs constitute over 60% of urban surfaces (roof 20-25%, pavements about 40%). The roof and the pavement albedo can be increased by about 0.25 and 0.10, respectively, resulting in a net albedo increase for urban areas of about 0.1. Many studies have demonstrated building cooling-energy savings in excess of 20% upon raising roof reflectivity from an existing 10-20% to about 60%. We estimate U.S. potential savings in excess of $1 billion (B) per year in net annual energy bills. Increasing albedo of urban surfaces can reduce the summertime urban temperature and improve the urban air quality. Increasing the urban albedo has the added benefit of reflecting more of the incoming global solar radiation and countering the effect of global warming. We estimate that increasing albedo of urban areas by 0.1 results in an increase of 3 x 10{sup -4} in Earth albedo. Using a simple global model, the change in air temperature in lowest 1.8 km of the atmosphere is estimated at 0.01K. Modelers predict a warming of about 3K in the next 60 years (0.05K/year). Change of 0.1 in urban albedo will result in 0.01K global cooling, a delay of {approx}0.2 years in …

Air pollution arising from the emission of nitrogen oxides as a result of combustion taking place in boilers, furnaces and engines, has increasingly been recognized as a problem. New methods to remove NO{sub x} emissions significantly and economically must be developed. The current technology for post-combustion removal of NO is the selective catalytic reduction (SCR) of NO by ammonia or possibly by a hydrocarbon such as methane. The catalytic decomposition of NO to give N{sub 2} will be preferable to the SCR process because it will eliminate the costs and operating problems associated with the use of an external reducing species. The most promising decomposition catalysts are transition metal (especially copper)-exchanged zeolites, perovskites, and noble metals supported on metal oxides such as alumina, silica, and ceria. The main shortcoming of the noble metal reducible oxide (NMRO) catalysts is that they are prone to deactivation by oxygen. It has been reported that catalysts containing tin oxide show oxygen adsorption behavior that may involve hydroxyl groups attached to the tin oxide. This is different than that observed with other noble metal-metal oxide combinations, which have the oxygen adsorbing on the noble metal and subsequently spilling over to the metal oxide. This observation …

Air pollution arising from the emission of nitrogen oxides as a result of combustion taking place in boilers, furnaces and engines, has increasingly been recognized as a problem. New methods to remove NO{sub x} emissions significantly and economically must be developed. The current technology for post-combustion removal of NO is the selective catalytic reduction (SCR) of NO by ammonia or possibly by a hydrocarbon such as methane. The catalytic decomposition of NO to give N{sub 2} will be preferable to the SCR process because it will eliminate the costs and operating problems associated with the use of an external reducing species. The most promising decomposition catalysts are transition metal (especially copper)-exchanged zeolites, perovskites, and noble metals supported on metal oxides such as alumina, silica, and ceria. The main shortcoming of the noble metal reducible oxide (NMRO) catalysts is that they are prone to deactivation by oxygen. It has been reported that catalysts containing tin oxide show oxygen adsorption behavior that may involve hydroxyl groups attached to the tin oxide. This is different than that observed with other noble metal-metal oxide combinations, which have the oxygen adsorbing on the noble metal and subsequently spilling over to the metal oxide. This observation …

The analysis of interactions between lineages at varying levels of genetic divergence can provide insights into the process of speciation through the accumulation of incompatible mutations. Ring species, and especially the Ensatina eschscholtzii system exemplify this approach. The plethodontid salamanders Ensatina eschscholtzii xanthoptica and Ensatina eschscholtzii platensis hybridize in the Central Sierran foothills of California. We compared the genetic structure across two transects (southern and northern Calaveras Co.), one of which was re-sampled over 20 years, and examined diagnostic molecular markers (eight allozyme loci and mitochondrial DNA) and a diagnostic quantitative trait (color pattern). Key results across all studies were: (i) cline centers for all markers were coincident and the zones were narrow, with width estimates of 730m to 2000m; (ii) cline centers at the northern Calaveras transect were coincident between 1981 and 2001, demonstrating repeatability over 5 generations; (iii) there are very few if any putative F1's, but a relatively high number of backcrossed individuals (57-86 percent) in the central portion of transects; (iv) we found substantial linkage disequilibrium in all three studies and strong heterozygote deficit both in northern Calaveras, in 2001, and southern Calaveras. Both linkage disequilibrium and heterozygote deficit show maximum values near the center of …

The results suggest that garnet phosphors can be engineered to function thermographically over desired temperature ranges by adjusting gallium content. Substituting gadolinium for the yttrium in the host matrix also has an effect but it is not as large. A silicate phosphor showed the greatest temperature dependence though it could not be excited to fluoresce by a blue LED. All the garnet phosphors could be excited with such a blue source. Two phosphors tested showed an increase in intensity with temperature. Other garnet and silicate materials as mentioned above will be tested in the future. In addition, some perovskite phosphors, such as GdAlO{sub 3}:Ce, will also be investigated.

The U.S. Department of Energy’s Pacific Northwest National Laboratory just completed a multi-year project to develop a fully tested and documented atmospheric dispersion modeling system (DUST TRANsport or DUSTRAN) to assist the U.S. Department of Defense in addressing particulate air quality issues at military training and testing ranges. This manual documents the DUSTRAN modeling system and includes installation instructions, a user’s guide, and detailed example tutorials.

The project Production Scale Implementation of a Petroleum Contaminated Soils Bioreactor was launched in FY00 and showed that bioremediation can be performed under strictly controlled conditions. Initial results showed a 50 percent reduction of total petroleum hydrocarbon concentration in soil from the Czechowice-Dziedzice refinery. It was determined that changes in the design and construction of the bioreactor could improve system performance.

The primary purpose of this project was to employ two geophysical imaging techniques, electrical resistivity tomography and cross-borehole ground penetrating radar, to image a controlled infiltration of a saline tracer under unsaturated flow conditions. The geophysical techniques have been correlated to other more traditional hydrologic measurements including neutron moisture measurements and induction conductivity logs. Images that resulted during two successive infiltrations indicate the development of what appear to be preferential pathways through the finer grained materials, although the results could also be produced by cationic capture of free ions in clays. In addition the site as well as the developing solute plume exhibits electrical anisotropy which is likely related to flow properties. However the geologic significance of this phenomenon is still under investigation.

We present a proposal for performing model-independent jets plus missing energy searches. Currently, these searches are optimized for mSUGRA and are consequently not sensitive to all kinematically-accessible regions of parameter space. We show that the reach of these searches can be broadened by setting limits on the differential cross section as a function of the total visible energy and the missing energy. These measurements only require knowledge of the relevant Standard Model backgrounds and can be subsequently used to limit any theoretical model of new physics. We apply this approach to an example where gluinos are pair-produced and decay to the LSP through a single-step cascade, and show how sensitivity to different gluino masses is altered by the presence of the decay chain. The analysis is closely based upon the current searches done at the Tevatron and our proposal requires only small modifications to the existing techniques. We find that within the MSSM, the gluino can be as light as 125 GeV. The same techniques are applicable to jets and missing energy searches at the Large Hadron Collider.

An experimental campaign to study hohlraum-driven ignition-like double-shell target performance using the Omega laser facility has begun. These targets are intended to incorporate as many ignition-like properties of the proposed National Ignition Facility (NIF) double-shell ignition design [1,2] as possible, given the energy constraints of the Omega laser. In particular, this latest generation of Omega double-shells is nominally predicted to produce over 99% of the (clean) DD neutron yield from the compressional or stagnation phase of the implosion as required in the NIF ignition design. By contrast, previous double-shell experience on Omega [3] was restricted to cases where a significant fraction of the observed neutron yield was produced during the earlier shock convergence phase where the effects of mix are deemed negligibly small. These new targets are specifically designed to have optimized fall-line behavior for mitigating the effects of pusher-fuel mix after deceleration onset and, thereby, providing maximum neutron yield from the stagnation phase. Experimental results from this recent Omega ignition-like double-shell implosion campaign show favorable agreement with two-dimensional integrated hohlraum simulation studies when enhanced (gold) hohlraum M-band (2-5 keV) radiation is included at a level consistent with observations.

This report identifies the names, committee assignments, dates of service, and (for Representatives) districts of the 229 women Members of Congress.

The initial value representation (IVR) of semiclassical (SC) theory is used in conjunction with the Meyer-Miller/Stock-Thoss description of electronic degrees of freedom in order to treat electronically non-adiabatic processes. It is emphasized that the classical equations of motion for the nuclear and electronic degrees of freedom that emerge in this description are precisely the Ehrenfest equations of motion (the force on the nuclei is the force averaged over the electronic wavefunction), but that the trajectories given by these equations of motion do not have the usual shortcomings of the traditional Ehrenfest model when they are used within the SC-IVR framework. For example, in the traditional Ehrenfest model (a mixed quantum-classical approach) the nuclear motion emerges from a non-adiabatic encounter on an average potential energy surface (a weighted average according to the population in the various electronic states), while the SC-IVR describes the correct correlation between electronic and nuclear dynamics, i.e., the nuclear motion is on one potential energy surface or the other depending on the electronic state. Calculations using forward-backward versions of SC-IVR theory (FB-IVR) are presented to illustrate this behavior. An even more approximate version of the SC-IVR, the linearized approximation (LSC-IVR), is slightly better than the traditional Ehrenfest …

Current fluctuations of cathodic arcs were recorded withhigh analog bandwidth (up to 1 GHz) and fast digital sampling (up to 5Gsamples/sec). The power spectral density of the arc current wasdetermined by fast Fourier transform clearly showing material dependent,non-linear features in the frequency domain. These features can beassociated with the non-linear impedance of the conducting channelbetween cathode and anode, driven by the explosive nature of electronemission and plasma formation. The characteristic times of less than 100ns can be associated with individual explosive processes, "ectons," andtherefore represent the short-time physical cutoff for the fractal modelof cathodic arcs.

None

The ability to accurately quantify the intrinsic resolution of chemically amplified photoresists is critical for the optimization of resists for extreme ultraviolet (EUV) Iithography. We have recently reported on two resolution metrics that have been shown to extract resolution numbers consistent with direct observation. In this paper we examine the previously reported contact-hole resolution metric and explore the sensitivity of the metric to potential error sources associated with the experimental side of the resolution extraction process. For EUV exposures at the SEMATECH Berkeley microfield exposure tool, we report a full-process error-bar in extracted resolution of 1.75 nm RMS and verify this result experimentally.

The ASME Code Case N-729-1 defines alternative examination requirements for the Control Rod Drive Mechanism (CRDM) upper head penetration nozzle welds. The basis for these examination requirements was developed as part of an Industry program conducted by the Materials Reliability Program (MRP) through the Electric Power Research Institute (EPRI). The results of this program were published in MRP-95 Rev. 1 and document a set of finite element weld residual stress analyses conducted on a variety of upper head penetration nozzles. The inspection zone selected by the industry was based on the stress where it was assumed that primary water stress corrosion cracking (PWSCC) would not initiate. As explained in MRP-95 Rev. 1, it has been illustrated that PWSCC does not occur in the Alloy 600 tube when the stresses are below the yield strength of that tube. Typical yield strengths at operating conditions for Alloy 600 range from 35 ksi to 65 ksi. A stress less than 20-ksi tension was chosen as a conservative range where PWSCC would not initiate. Over the last several years, Engineering Mechanics Corporation of Columbus (Emc2) has conducted welding residual stress analyses on upper head penetration J-welds made from Alloy 182 weld metal for the …

A new method that combines staggered grid Arbitrary Lagrangian-Eulerian (ALE) techniques with structured local adaptive mesh refinement (AMR) has been developed for solution of the Euler equations. This method facilitates the solution of problems currently at and beyond the boundary of soluble problems by traditional ALE methods by focusing computational resources where they are required through dynamic adaption. Many of the core issues involved in the development of the combined ALEAMR method hinge upon the integration of AMR with a staggered grid Lagrangian integration method. The novel components of the method are mainly driven by the need to reconcile traditional AMR techniques, which are typically employed on stationary meshes with cell-centered quantities, with the staggered grids and grid motion employed by Lagrangian methods. Numerical examples are presented which demonstrate the accuracy and efficiency of the method.

Bioenergy crops, which displace fossil fuels when used to produce ethanol, biobased products, and/or electricity, have the potential to further reduce atmospheric carbon levels by building up soil carbon levels, especially when planted on lands where these levels have been reduced by intensive tillage. The purpose of this study is to improve the characterization of the soil carbon (C) sequestration for bioenergy crops (switchgrass, poplars, and willows) in the Greenhouse gases, Regulated Emissions, and Energy Use in Transportation (GREET) model (Wang 1999) by using the latest results reported in the literature and by Oak Ridge National Laboratory (ORNL). Because soil carbon sequestration for bioenergy crops can play a significant role in reducing greenhouse gas (GHG) emissions for cellulosic ethanol, it is important to periodically update the estimates of soil carbon sequestration from bioenergy crops as new and better data become available. We used the three-step process described below to conduct our study.

EPIcode (version 7.0) and ALOHA (version 5.2.3) are two of the designated toolbox codes identified in the Department of Energy's Implementation Plan for DNFSB Recommendation 2002-1 on Software Quality Assurance issues in the DOE Complex. Both have the capability to estimate evaporation rates from pools formed from chemical spills and to predict subsequent atmospheric transport and dispersion. This paper provides an overview of the algorithms used by EPIcode and ALOHA to calculate evaporation rates and downwind plume concentrations. The technical bases for these algorithms are briefly discussed, and differences in the EPIcode and ALOHA methodologies highlighted. In addition, sample calculations are performed using EPIcode and ALOHA for selected chemicals under various environmental conditions. Side-by-side comparisons of results from sample calculations are analyzed to illustrate the impact that the different methodologies used by EPIcode and ALOHA have on predicted evaporation rates and downwind concentrations.

This report discusses various aspects of the Department of Defense's (DOD) fuel consumption and any resulting policy considerations for Congress.

New materials and corresponding manufacturing processes are likely candidates for diesel engine components as society and customers demand lower emission engines without sacrificing power and fuel efficiency. Strategies for improving thermal efficiency directly compete with methodologies for reducing emissions, and so the technical challenge becomes an optimization of controlling parameters to achieve both goals. Approaches being considered to increase overall thermal efficiency are to insulate certain diesel engine components in the combustion chamber, thereby increasing the brake mean effective pressure ratings (BMEP). Achieving higher BMEP rating by insulating the combustion chamber, in turn, requires advances in material technologies for engine components such as pistons, port liners, valves, and cylinder heads. A series of characterization tests were performed to establish the material properties of ceramic powder. Mechanical chacterizations were also obtained from the selected materials as a function of temperature utilizing ASTM standards: fast fracture strength, fatique resistance, corrosion resistance, thermal shock, and fracture toughness. All ceramic materials examined showed excellent wear properties and resistance to the corrosive diesel engine environments. The study concluded that the ceramics examined did not meet all of the cylinder head insert structural design requirements. Therefore we do not recommend at this time their use for …

This report is about the Broadband Internet Access, The Background and analysis of Broadband. It's importance, and about broadband technologies like Cable, Satellite and other technologies. The status of Broadband Deployment and Development Issues.