Solid state experiments at very high pressures and strain rates are possible on high power laser facilities, albeit over brief intervals of time and spatial small scales. A new shockless drive has been developed on the Omega laser. VISAR measurements establish the high strain rates, 10{sup 7}-10{sup 8} s{sup -1}. Solid-state strength is inferred using the Rayleigh-Taylor instability as a ''diagnostic''. Temperature and compression in polycrystalline samples can be deduced from EXAFS measurements. Lattice response can be inferred from time-resolved x-ray diffraction. Deformation mechanisms can be identified by examining recovered samples. We will briefly review this new area of laser-based materials science research, then present a path forward for carrying these solid-state experiments to much higher pressures, P >> 1 Mbar, on the NIF laser facility.

Fast intermittent transport has been observed in the scrape-off layer (SOL) of major tokamaks including Alcator C-Mod, DIII-D, and NSTX. This kind of transport is not diffusive but rather convective. It strongly increases plasma flux to the chamber walls and enhances the recycling of neutral particles in the main chamber. We discuss anomalous cross-field convection (ACFC) model for impurity and main plasma ions and its relation to intermittent transport events, i.e. plasma density blobs and holes in the SOL. Along with plasma diffusivity coefficients, our transport model introduces time-independent anomalous cross-field convective velocity. In the discharge modelling, diffusivity coefficients and ACFC velocity profiles are adjusted to match a set of representative experimental data. We use this model in the edge plasma physics code UEDGE to simulate the multi-fluid two-dimensional transport for these three tokamaks. We present simulation results suggesting the dominance of anomalous convection in the far SOL transport. These results are consistent with the hypothesis that the chamber wall is an important source of impurities and that different impurity charge states have different directions of anomalous convective velocity.

Previous analyses have assumed that wedge absorbers are triangularly shaped with equal angles for the two faces. In this case, to linear order, the energy loss depends only on the position in the direction of the face tilt, and is independent of the incoming angle. One can instead construct an absorber with entrance and exit faces facing rather general directions. In this case, the energy loss can depend on both the position and the angle of the particle in question. This paper demonstrates that and computes the effect to linear order.

Aquifer microcosms were used to determine how ethanol and methyl-tert-butyl ether (MtBE) affect monoaromatic hydrocarbon degradation under different electron-accepting conditions commonly found in contaminated sites experiencing natural attenuation. Response variability was investigated by using aquifer material from four sites with different exposure history. The lag phase prior to BTEX (benzene, toluene, ethylbenzene, and xylenes) and ethanol degradation was typically shorter in microcosms with previously contaminated aquifer material, although previous exposure did not always result in high degradation activity. Toluene was degraded in all aquifer materials and generally under a broader range of electron-accepting conditions compared to benzene, which was degraded only under aerobic conditions. MtBE was not degraded within 100 days under any condition, and it did not affect BTEX or ethanol degradation patterns. Ethanol was often degraded before BTEX compounds, and had a variable effect on BTEX degradation as a function of electron-accepting conditions and aquifer material source. An occasional enhancement of toluene degradation by ethanol occurred in denitrifying microcosms with unlimited nitrate; this may be attributable to the fortuitous growth of toluene-degrading bacteria during ethanol degradation. Nevertheless, experiments with flow-through aquifer columns showed that this beneficial effect could be eclipsed by an ethanol-driven depletion of electron acceptors, which …

Geophysical models are increasingly recognized as an important component of regional calibrations for seismic monitoring. The models can be used to predict geophysical measurements, such as body wave travel times, and can be derived from direct regional studies or even by geophysical analogy. While empirical measurements of these geophysical parameters might be preferred, in aseismic regions or regions without seismic stations, this data might not exist. In these cases, models represent a 'best guess' of the seismic properties in a region, which improves on global models such as the PREM (Preliminary Reference Earth Model) or the IASPEI (International Association of Seismology and Physics of the Earth's Interior) models. The model-based predictions can also serve as a useful background for the empirical measurements by removing trends in the data. To this end, Lawrence Livermore National Laboratory (LLNL) has developed the WENA model for Western Eurasia and North Africa. This model is constructed using a regionalization of several dozen lithospheric (crust and uppermost mantle) models, combined with the Laske sediment model and 3SMAC upper mantle. We have evaluated this model using a number of data sets, including travel times, surface waves, receiver functions, and waveform analysis. Similarly, Los Alamos National Laboratory (LANL) …

We apply recent analytic solutions to the radiation diffusion equation to problems of interest for ICF hohlraums. The solutions provide quantitative values for absorbed energy which are of use for generating a desired radiation temperature vs. time within the hohlraum. Comparison of supersonic and subsonic solutions (heat front velocity faster or slower, respectively, than the speed of sound in the x-ray heated material) suggests that there may be some advantage in using high Z metallic foams as hohlraum wall material to reduce hydrodynamic losses, and hence, net absorbed energy by the walls. Analytic and numerical calculations suggest that the loss per unit area might be reduced {approx} 20% through use of foam hohlraum walls. Reduced hydrodynamic motion of the wall material may also reduce symmetry swings, as found for heavy ion targets.

The performance of object-oriented applications often suffers from the inefficient use of high-level abstractions provided by underlying libraries. Since these library abstractions are user-defined and not part of the programming language itself only limited information on their high-level semantics can be leveraged through program analysis by the compiler and thus most often no appropriate high-level optimizations are performed. In this paper we outline an approach based on source-to-source transformation to allow users to define optimizations which are not performed by the compiler they use. These techniques are intended to be as easy and intuitive as possible for potential users; i.e. for designers of object-oriented libraries, people most often only with basic compiler expertise.

None

Astronomical applications of adaptive optics at Lawrence Livermore National Laboratory (LLNL) has a history that extends from 1984. The program started with the Lick Observatory Adaptive Optics system and has progressed through the years to lever-larger telescopes: Keck, and now the proposed CELT (California Extremely Large Telescope) 30m telescope. LLNL AO continues to be at the forefront of AO development and science.

The authors present measurements of the angular cross-correlation between luminous red galaxies from the Sloan Digital Sky Survey and the cosmic microwave background temperature maps from the Wilkinson Microwave Anisotropy Probe. They find a statistically significant achromatic positive correlation between these two data sets, which is consistent with the expected signal from the late Integrated Sachs-Wolfe (ISW) effect. they do not detect any anti-correlation on small angular scales as would be produced from a large Sunyaev-Zel'dovich (SZ) effect, although they do see evidence for some SZ effect for their highest redshift samples. Assuming a flat universe, their preliminary detection of the ISW effect provides independent physical evidence for the existence of dark energy.

Success in the application of the action and phase analysis to find linear errors at RHIC Interaction Regions [1] has encouraged the creation of a technique based on the action and phase analysis to find non linear errors. In this paper we show the first attempt to measure the sextupole components at RHIC interaction regions using the action and phase method. Experiments done by intentionally activating sextupoles in RHIC and in SPS [2] will also be analyzed with this method. First results have given values for the sextupole errors that at least have the same order of magnitude as the values found by an alternate technique during the RHIC 2001 run [3].

A theoretical model of afterburning in explosions created by turbulent mixing of the detonation products from fuel-rich charges with air is described. It contains three key elements: (i) a thermodynamic-equilibrium description of the fluids (fuel, air, and products), (ii) a multi-component gas-dynamic treatment of the flow field, and (iii) a sub-grid model of molecular processes of mixing, combustion and equilibration.

We present the first results from fully general relativistic numerical studies of thick-disk accretion onto a rapidly-rotating (Kerr) black hole with a spin axis that is tilted (not aligned) with the angular momentum vector of the disk. We initialize the problem with the solution for an aligned, constant angular momentum, accreting thick disk around a black hole with spin a/M = J/M{sup 2} = +0.9 (prograde disk). The black hole is then instantaneously tilted, through a change in the metric, by an angle {beta}{sub 0}. In this Letter we report results with {beta}{sub 0} = 0, 15, and 30{sup o}. The disk is allowed to respond to the Lense-Thirring precession of the tilted black hole. We find that the disk settles into a quasi-static, twisted, warped configuration with Lense-Thirring precession dominating out to a radius analogous to the Bardeen-Petterson transition in tilted Keplerian disks.

In contrast to failure approaches at the lamina level or the micromechanics level the present work concerns failure characterization at the laminate level. Specifically, attention is given to the ultimate failure characterization for quasi-isotropic laminates. This is in further contrast to the commonly used approaches for initial damage or progressive damage. It is shown that the analytical failure forms decompose into two modes, one for out of plane, delamination type failure and one for in plane, fiber controlled type failure. The work here is mainly given over to the delamination mode of failure. Experimental results are presented for laminates in this mode of failure. These results are then integrated with the analytical forms to give a simple criterion for delamination failure.

In most Cu(In,Ga)Se2 thin films used for solar cells, there usually exist interfaces lying about 0.1 to 0.2 m below the surfaces. We report on a convergent-beam electron diffraction and energy-dispersive X-ray spectroscopy study of the microstructure and chemical composition of the surface region in Cu(In,Ga)Se2 thin films. We find that the surface region and the bulk are structurally similar, with no ordered defect chalcopyrite structure observed. However, their composition is slightly different, indicating that they can have different point-defect physics. Our results suggest that the subinterfaces and the bulk absorber may form homojunctions.

Beam induced electron multipacting may be among the main reasons for the vacuum pressure rise when circulating high intensity ion and proton beams in RHIC. Latest simulation results are benchmarked with recent experimental observations for RHIC, and compared to other general computer codes. The influence of the electron multipacting to the vacuum properties is also discussed.

As one of the most critical system for RHIC operation, the beam abort kicker system has to be highly available, reliable, and stable for the entire operating range. Along with the RHIC commission and operation, consistent efforts have been spend to cope with immediate issues as well as inherited design issues. Major design changes have been implemented to achieve the higher operating voltage, longer high voltage hold-off time, fast retriggering and redundant triggering, and improved system protection, etc. Recent system test has demonstrated for the first time that both blue ring and yellow ring beam abort systems have achieved more than 24 hours hold off time at desired operating voltage. In this paper, we report break down, thyratron reverse arcing, and to build a fast re-trigger system to reduce beam spreading in event of premature discharge.

We used synthetic aperture radar interferograms to image ground subsidence that occurred over the Dixie Valley geothermal field during different time intervals between 1992 and 1997. Linear elastic inversion of the subsidence that occurred between April, 1996 and March, 1997 revealed that the dominant sources of deformation during this time period were large changes in fluid volumes at shallow depths within the valley fill above the reservoir. The distributions of subsidence and subsurface volume change support a model in which reduction in pressure and volume of hot water discharging into the valley fill from localized upflow along the Stillwater range frontal fault is caused by drawdown within the upflow zone resulting from geothermal production. Our results also suggest that an additional source of fluid volume reduction in the shallow valley fill might be similar drawdown within piedmont fault zones. Shallow groundwater flow in the vicinity of the field appears to be controlled on the NW by a mapped fault and to the SW by a lineament of as yet unknown origin.

A source evaluation case study is presented for observations of algae toxicity in an intermittent stream passing through the Lawrence Livermore National Laboratory near Livermore, California. A five-step procedure is discussed to determine the cause of water toxicity problems and to determine appropriate environmental management practices. Using this approach, an upstream electrical transfer station was identified as the probable source of herbicides causing the toxicity. In addition, an analytical solution for solute transport in overland flow was used to estimate the application level of 40 Kg/ha. Finally, this source investigation demonstrates that pesticides can impact stream water quality regardless of application within levels suggested on manufacturer labels. Environmental managers need to ensure that pesticides that could harm aquatic organisms (including algae) not be used within close proximity to streams or storm drainages and that application timing should be considered for environmental protection.

The current waste package design for the proposed repository at Yucca Mountain Nevada, USA, employs gas tungsten arc welding (GTAW) in fabricating the waste packages. While GTAW is widely used in industry for many applications, it requires multiple weld passes. By comparison, single-pass welding methods inherently use lower heat input than multi-pass welding methods which results in lower levels of weld distortion and also narrower regions of residual stresses at the weld TWI Ltd. has developed a Reduced Pressure Electron Beam (RPEB) welding process which allows EB welding in a reduced pressure environment ({le} 1 mbar). As it is a single-pass welding technique, use of RPEB welding could (1) achieve a comparable or better materials performance and (2) lead to potential cost savings in the waste package manufacturing as compared to GTAW. Results will be presented on the initial evaluation of the RPEB welding on a Ni-Cr-Mo alloy (a candidate alloy for the Yucca Mountain waste packages) in the areas of (a) design and manufacturing simplifications, (b) material performance and (c) weld reliability.

Facilities to support development of modified nitride-based reactor fuel pellets have been activated and are now in operation at Lawrence Livermore National Laboratory. These facilities provide the controls and monitored laboratory conditions required to produce, evaluate, and verify quality of the nitride-based product required for this fuel application. By preserving the high melting point, high thermal conductivity, and high actinide density properties of nitride fuel while enhancing stoichiometry, density, and grain structure, and by applying inert matrix (ZrN) and neutron absorbing (HfN) additives for improved stability and burn-up characteristics, the requirements for a long-life fuel to support sealed core reactor applications may be met. This paper discusses requirements for producing the modified nitride powders for sintering of fuel pellets, translation of these requirements into facility specifications, and implementation of these specifications as facility capabilities.

This paper discusses issues with the limited precision of hardware-based volume visualization. We will describe the compositing OVER operator and how fixed-point arithmetic affects it. We propose two techniques to improve the precision of fixed-point compositing and the accuracy of hardware-based volume visualization. The first technique is to perform dithering of color and alpha values. The second technique we call exponent-factoring, and captures significantly more numeric resolution than dithering, but can only produce monochromatic images.

This report is a summary of the discussion sessions of the 12th Workshop on Crystalline Silicon Solar Cells and Processes. The theme of the workshop was"Fundamental R&D in c-Si: Enabling Progress in Solar-Electric Technology." This theme was chosen to reflect a concern that the current expansion in the PV energy production may redirect basic research efforts to production-oriented issues. The PV industry is installing added production capacity and new production lines that include the latest technologies. Once the technologies are selected, it is difficult to make changes. Consequently, a large expansion can stagnate the technologies and diminish interest in fundamental research. To prevent the fundamental R&D program from being overwhelmed by the desire to address immediate engineering issues, there is a need to establish topics of fundamental nature that can be pursued by the universities and the research institutions. Hence, one of the objectives of the workshop was to identify such areas for fundamental research.

Positronium (Ps) is simulated using Path Integral Monte Carlo (PIMC). This method can reproduce the results of previous simple theories in which a single quantum particle is used to represent Ps within an idealized pore. In addition, the calculations treat the e{sup -} and e{sup +} of Ps exactly and realistically model interactions with solid atoms, thereby correcting and extending the simpler theory. They study the pick-off lifetime of o-Ps and the internal contact density, {kappa}, which controls the self-annihilation behavior, for Ps in model voids (spherical pores), defects in a solid (argon), and microporous solids (zeolites).