From abstract: "This bibliography consists of reports compiled from the AEC Library Card Catalog. Only the Classified and Unclassified report literature is included. For the published literature the reader is referred to an unpublished paper by V. Carson (UCRL - Livermore Library)" titled "Radioactive Waste Disposal" (April 25, 1957). "All progress reports covering the work have been omitted in order to exclude a large amount of duplicate information which is usually found in more detail in topical reports."

Report presenting a transonic investigation of the static-pressure fluctuations in the left duct of a scale inlet model of a supersonic fighter-bomber airplane in the transonic tunnel. Results regarding amplitude characteristics of pressure fluctuations, power-spectral analyses, and flow distortions at compressor face are provided.

Abstract: "Fabrication techniques for producing dispersion fuel elements with cores of 30 volume per cost of UC, U2Tl, U3Si, or U6Ni dispersed in Zircology 2 and 30 volume per cent of UC or UN dispersed in Type 18-8 stainless steel have been investigated. Roll-clad plate-type elements of all these compositions may be fabricated by powder-metallurgy methods in such a manner that good core-to-cladding bonds and cores with uniform dispersions of discrete uranium-composed particles are obtained. From the standpoint of fabricability, elements containing UC is Zircology 2, UC in stainless steel, and UN in stainless steel are the most promising. The UN in stainless steel has the best corrosion resistance in 680 F degassed water; however, UC in stainless steel has the best resistance to corrosion in 700 F NaK."

Investigation of the flow through straight-through , elbow, and tee "AN" fittings at negligible approach velocity with approach temperatures up to 1100 degrees F.

"A two-dimensional wind-tunnel investigation of the flow and force characteristics of four NACA 6A-series airfoils with thickness ratios of 4, 6, and 9 percent has been conducted in the Langley airfoil test apparatus at at transonic Mach numbers between 0.8 and 1.25. The Reynolds number range for these tests varied from 2.6 x 10(6) to 2.8 x 10(6). As was expected, the airfoils exhibited a smooth transition in force coefficients from a Mach number of 1.0 to the values obtained at the higher speeds. Lift-curve slope and maximum lift-drag ratio correlated very well on a basis of the transonic similarity laws at Mach numbers above 1.0, but below that value the correlation was not good" (p. 1).

From Introduction: "The heat-transfer data calculated from measured temperatures are compared with values calculated by the theory of Van Driest for a flat plate with laminar and turbulent boundary layers. In addition, the heat-transfer data from the flight tests are compared with data obtained from the Langley Structures Research Division of ground tests of an identical wing at a Mach number approximately equal to 1.99 in the pre-flight jet of the Langley Pilotless Aircraft Research Station at Wallops Island, Va. The stream static pressure is maintained at about 1 atmosphere, the free-stream temperature at about 75^o F, and the stagnation temperature at approximately 500 ^o F (ref.1)."

"An analog computer study was made in order to investigate the inertia coupling in rolling maneuvers of an airplane configuration utilizing a variable-incidence wing for longitudinal control. A five-degree-of-freedom system of equations was used, and only one set of flight conditions was included in this study. The results, when compared to those for a conventional tail-control airplane, indicated significant advantages for the variable-incidence-wing type of control in reducing undesired dynamic effects during rolling maneuvers" (p. 1).

An investigation of the burning rates of single drops of 15 hydrocarbon and nonhydrocarbon fuels in quiescent air at room temperature and pressure. The drop burning rates were found to be proportional to drop diameter. The experimentally determined drop burning rates were in orderly agreement with those predicted by theoretical analysis, but the absolute values differed significantly.

Report presenting a transonic investigation of the static-pressure fluctuations in the left duct of a scale inlet model of a supersonic fighter-bomber airplane. The amplitude and frequency of pressure fluctuations were measured using an electrical pressure gage mounted on the diffuser wall at several Mach numbers and mass-flow ratios. Results regarding amplitude characteristics of pressure fluctuations, power-spectral analyses, and flow distortions at compressor face are provided.

The static longitudinal and lateral stability characteristics of an 0.065-scale model of the XRSSM-N-9a (REGULUS II) missile at Mach number range of 1.6 to 2.0 at a Reynolds number per foot of 2.0(exp 8).

"The addition of fuselage volume, concentrated on top of the forward portion of the fuselage, for the purpose of delaying the drag-rise Mach number of subsonic airplanes at lifting conditions is investigated. The additions have been designed on the basis of the area rule and other important considerations to provide greater practicability of application compared with shapings previously investigated. The addition delayed the drag-rise Mach number by an increment of approximately 0.03 for a configuration having a wing with moderate thickness and 35 deg of sweepback at a lift coefficient of 0.3. A lesser delay was obtained for a configuration with a thicker wing. The additions increase the nonlinearities of the variations of pitching moment with lift" (Abstract).

In the HRP Welding program, a major part of the welding and fabrication, and some of the testing, is performed using an inert atmosphere. the use of the inert gas consumable arc welding process and dry box welding or other work in a dry box comes within this category. Since much of the work in the project make use of, or requires, inert atmospheres, a general discussion follows of the methods used, description of equipment, processes, quality of atmospheres, purity requirements, kinetics of metal-gas reactions, and the proper application of the equipment and methods use din obtaining the desired results.

General considerations involving the transportation of irradiated fuel and radioactive wastes are reviewed. It is assumed that many reactors will supply feed to a few large multipurpose chemical plants which ultimately send radioactive waste to a few disposal sites. General economic considerations of irradiated fuel reprocessing, economic aspects of the nuclear economy complex, growth predictions of the nuclear power economy in the U.S., general requirements for the shipment of fuel and waste, regulations applicable to fuel shipment, and permissible radiation levels are discussed.

Specifications are presented for cleanliness during installation of piping and equipment in the High Level Volatility Laboratory, Bldg. 4507.