From introduction: The principal work described below is the development and tests of a slow neutron flux generator based on a generator developed at the University of California (UCRL 8359, W. Patterson, Roger Wallace, "A Method of Calibrating Slow Neutron Detectors"). It is shown that a tolerance flux density of slow neutrons results within a cubical cavity 15 inches on an edge with 4-inch-thick walls of water or paraffin wax when a plutonium-beryllium source emitting about 7 million neutrons per second is placed within the cavity according to a standard procedure. The principle on which the generator is based is that the fast neutrons from the source are slowed to near thermal velocities by scattering from the cavity walls. (Although the principal interest is in the slow flux, a primary fast flux is present at any point depending on the inverse square of the distance from the source.) The variation of slow neutron flux density over the walls of the cavity is unimportant for the calibration of thermal neutron detectors which follow a 1/v or 1/E response law (where v and E are the neutron velocity and energy), so that the detector is sensitive mainly to the slow neutron flux. …

Introduction: "It is the purpose of this note to describe the construction and operation of the plasma injectors used in the magnetic high compression experiments in progress at the Lawrence Radiation Laboratory at Livermore. As the investigations of these injections is still in progress, remarks concerning their operation or the characteristics of the injected plasma are of a tentative nature."

The Fermi age of thermal neutrons in a lattice containing both water and graphite in some sort of weighted average of the age in water and in graphite independently, with correction for volumes of non-moderating elements or voids. The correct weighting function has been in question during design calculations for the NPR. This paper presents a very simple and direct approach to the problem, resulting in a weighting equation which seems to be theoretically sound. Unfortunately, simple theories cannot be guaranteed to give good results in complicated systems; nevertheless, it appears that the weighting dunction derived here is to be preferred over methods involving empirical relationships which are of doubtful validity in the NPR geometry.

Preface: The intermediate heat exchanger is designed for operation in a nuclear power plant using liquid sodium as the primary and secondary coolant. Since the primary fluid coming from the reactor is radioactive, the purpose of the IHX is to transfer heat to a nonradioactive fluid which then goes to a steam generator. Because of this activity the until will be enclosed in a concrete pit and will not be accessible during periods of operation. Immediately after shut down it will be necessary to allow time for radioactive decay before the unit will be accessible to personnel. Because of inaccessibility and possible long periods allowed for decay time, it is imperative that the unit give trouble free operation. During periods of shut down, the internals should have easy access for inspection and repair if necessary so that down time is held to a minimum. The general arrangement of the heat exchanger described in this report presents a conventional design utilizing known materials and existing methods of fabrication. In further consideration of all concepts, designs and analyses developed during this period of the program, it is felt that this preliminary design will provide an intermediate sodium heat exchanger of lower cost …

This report is an outgrowth of the MURA Users' Conference of June 1959. At that conference the group on beam separators discussed the problem of whether particle separation could be achieved at the machine energies under consideration. A preliminary version of the scheme outlined here was given at the conference. Later, after flaws were discovered, it was modified. The attempt is not to show that this is the way it should be done, but to show with reasonable certainty that there is at least one way it can be done.

The discharge of cooling water from the Hanford reactors introduce radioactive contaminants to the Columbia River. These materials may subsequently bring about exposure to human populations either through the direct use of the water for sanitary purposes or transfers of the radioisotopes into the food chains. It is therefore desirable to keep to a minimum the amounts of radioisotopes released to the river.

Volstility Pilot Plant Mark III Fluorinator will be a double-chamber type vessel, each chamber 2-1/2ft. by 16in. o.d. separated by a 5 in. pipe 15 in. long. ASME flanged and dished heads will be used for the chamber tops and conical sections with a 60º apex angle for the chamber bottoms. A new furnace designed to maintain the complete lower chamber (molten salt + freeboard) above melt temperature will eliminate past experiences of salt solidification on the wall, heads, and in or on the internal process lines. External pipe runs will be sutoresistance heated to allow melting and drain back of salt plugs. The upper chamber serves as a gas de-entrainment and solids precipitation device to retain most of the entrained salt and condensable fluorides in the 100-400°C temperature range.

Available knowledge of precision limits in S.S. accountability measurements and/or calculations by reactor and chemical processing groups is surveyed and summarizes. Experience in comparisons of reactor (production and research) calculations versus chemical plant accountability measurements is also reported. A general tentative conclusion is that available precisions (+/- 0.54 to +/- 0.78% ) in chemical plant measurements is also reported. A general tentative conclusion is that available precisions (+/- 1.0 to +/- 11.0%) possible by calculations (nuclear and/or engineering) of power reactor systems; however, with operation and empirical experience (e.g. less than +/-1.0%

From foreword: This report describes the goal of the overall SDR program to demonstrate the commercial generation of electrical power.