Various figures depicting views and components of a device for coating the "Model 100" 8-faced metallic rotating mirror with an equal amount of material on each mirror face.

Memorandum presenting Mach number histories of the motion experienced by a hypothetical, small, straight-wing aircraft accelerating at various rates through an assumed controls-fixed pitch-down balance change in the transonic range. Two approximate analytical solutions of the longitudinal equations of motion are developed which are based on certain simplifying assumptions indicated by the differential-analyzer results.

Report presenting results of an exploratory free-flight investigation at zero lift of several rocket-powered drag research models equipped wing wing tanks at a range of Mach numbers. The tanks, which were slender bodies of revolution, were mounted on 34 degrees sweptback, nontapered wings of 2.7 aspect ratio. Results regarding drag and trim change are provided.

This report presents an analysis of a compound engine operating with manifold pressures ranging from 60 to 110 lb/sq in. absolute and discusses the effects of engine limits (peak cylinder pressure and turbine-inlet temperature) and component efficiency.

Report presenting an investigation of the performance and general operating characteristics of a small single-cylinder, two-stroke-cycle, loop-scavenged engine using compression ignition at low compression ratios, high inlet-manifold temperatures and high inlet-manifold and exhaust-gas pressures. Results regarding the scavenging characteristics, power output, cylinder pressures, thermal efficiency, and exhaust measurements are provided.

Report presenting an experimental investigation of the downwash and sidewash flow angles in a transverse plane behind a cruciform-wing and body combination. The wing-body combination had a cruciform arrangement of two identical triangular wings of aspect ratio 2.31 corresponding to a leading-edge sweep angle of 60 degrees placed on a body of fineness ratio of 16. The investigation was conducted at a specified Mach and Reynolds number and a range of angles of bank and attack.

"Pressure-distribution measurements and load-coefficient data at low speeds obtained in flight for a conventional front and rear sliding canopy are presented. The load-coefficient data indicate that the highest net aerodynamic load for the front canopy was in the exploding direction and occurred with the front and rear canopies closed. The highest net load for the rear canopy was in the crushing direction with the front canopy open and the rear canopy closed" (p. 1).

Report discussing static testing on 3 NACA two-blade propellers with design lift coefficients of 0, 0.3, and 0.5. Information about the effect of camber on the static-thrust figure of merit, the effect of camber on the stall-flutter speed, thrust coefficient, and blade flutter is provided.

Report presenting an investigation in the free-flight tunnel to determine the dynamic lateral stability and control characteristics of a coupled airplane configuration with simplified fighter models attached to the wing tips of a simplified bomber model. The configuration is meant to represent fighter airplanes carried on the wing tips of a bomber airplane to provide fighter protection for the bomber or for in-flight fueling. Results regarding the fighters attached with freedom in roll, with freedom in roll and pitch, and with freedom in roll, pitch, and yaw are provided.

A method is presented for the determination of the contour of disks, typified by those of aircraft gas turbines, to incorporate arbitrary elastic-stress distributions resulting from either centrifugal or combined centrifugal and thermal effects. The specified stress may be radial, tangential, or any combination of the two. Use is made of the finite-difference approach in solving the stress equations, the amount of computation necessary in the evolution of a design being greatly reduced by the judicious selection of point stations by the aid of a design chart. Use of the charts and of a preselected schedule of point stations is also applied to the direct problem of finding the elastic and plastic stress distribution in disks of a given design, thereby effecting a great reduction in the amount of calculation. Illustrative examples are presented to show computational procedures in the determination of a new design and in analyzing an existing design for elastic stress and for stresses resulting from plastic flow.

The results of an experimental investigation of the effect of oil inlet distribution and oil inlet temperature on the inner and outer-race temperatures of 75-millimeter-bore (size 215) cylindrical-roller inner-race-riding cage-type bearings are reported. A radial-load test rig was used over a range of dn values (product of the bearing bore in mm and the shaft speed in r.p.m) from 0.3 x 10(5) to 1.2 x 10(6) and static radial loads from 7 to 1113 pounds.

Report presenting an investigation to determine the effects of taper ratio and body indentation on the aerodynamic loading characteristics of a 45 degree sweptback wing in the presence of a body in the transonic pressure tunnel for a range of Mach numbers and angles of attack. Results regarding the effect of wing-body-juncture seals, general effects of the variables, effect of taper ratio, effects of body indentation, and comparisons with other data are provided.

Report presenting an investigation to obtain the effects of a 20-percent-semispan all-movable wing-tip control on the longitudinal stability characteristics of a twisted and cambered 60 degree sweptback-wing-indented-body configuration. Testing occurred over a range of angles of attack and Mach numbers. Results regarding the effects on drag coefficient and lift-drag ratio are also provided.

"The equations are presented for the development of the compressible laminar boundary layer over a yawed infinite cylinder. For compressible flow with a pressure gradient the chordwise and spanwise flows are not independent. Using the Stewartson transformation and a linear viscosity-temperature relation yields a set of three simultaneous ordinary differential equations in a form yielding similar solutions. These equations are solved for stagnation-line flow for surface temperatures from zero to twice the free-stream stagnation temperature and for a wide range of yaw angle and free-stream Mach number" (p. 1017).

Report presenting zero-lift experimental flutter data in a range of Mach numbers on a 1.5-percent-thick, untapered, unswept, solid steel wing with hexagonal airfoil sections and wing length-to-chord ratios of 1.61 and 1.73. The wing was tested as a cantilever with and without a half-body-of-revolution fuselage. Results regarding the calculated flutter speeds and frequencies, effect of fuselage, variation of wing flutter characteristics with Mach number, results of analytic solutions, and variation of wing flutter characteristics with mass ratio are provided.

Report presenting flutter data over a range of Mach numbers in free-flight testing of several wing-body combinations as part of a general zero-lift drag investigation. The wings all had the same streamwise airfoil sections and the plan-form variations consisted of delta wings, diamond wings, and an arrow wing. Time histories of model speed, Mach number, and air density are provided for each model as well as flutter frequency, amplitude, and reduced-frequency parameter plotted as functions of model speed.

Report presenting a flight investigation over a range of altitudes and lift to determine the wing loads of the Bell X-5 research airplane at a sweep angle of 58.7 degrees at subsonic and transonic Mach numbers. Testing indicated that wing loads exhibit nonlinear trends over the angle-of-attack range from zero to maximum wing lift.

A report about the absorption spectra of the thallium-dithizone mixed-color system. An analytical procedure based on this system is given which is applicable to pure solutions.

Introduction: "A corrosion test program, to determine the suitability of LaBour B-55 and Worthite for use in the construction of circulating pumps for th UO3 process has been completed and the data are appended."

Report discussing statistical quality control for the period of December, 1951-February, 1952. Statistical quality control is provided for studies of the General Ionic Analyses Laboratory, the HR Control Laboratory, and the X-10 Laboratories.

An engineering-scale demonstration of the Sulfex process indicated that semi-continuous decladding of unirradiated stainless steel-clad UO2 or U02ThO2 fuels is feasible.

Report documenting research and developments made by the Maritime Reactor Program of the Oak Ridge National Laboratory.

From summary: "This report was prepared for the Advisory Committee on Reactor Safeguards for their review and consideration of the potential hazards concerning the Battelle Memorial Institute Research Reactor."

Memorandum presenting an investigation in the 7- by 10-foot tunnel of the static longitudinal and lateral stability characteristics of a model with an unswept wing and several different tail arrangements. The shapes tested include a Y-tail, a cruciform tail, and a more conventional T-tail. Results regarding wing-body characteristics, effects of stabilizer incidence on lateral characteristics, T-tail characteristics, Y-tail characteristics, X-tails, estimated tail contribution, and characteristics referred to the body-axis system are provided.