In support of technology development to utilize coal for efficient, affordable, and environmentally clean power generation, the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama, routinely demonstrates gasification technologies using various types of coals. The PSDF is an engineering scale demonstration of key features of advanced coal-fired power systems, including a KBR (formerly Kellogg Brown & Root) Transport Gasifier, a hot gas particulate control device, advanced syngas cleanup systems, and high-pressure solids handling systems. This report discusses Test Campaign TC16 of the PSDF gasification process. TC16 began on July 14, 2004, lasting until August 24, 2004, for a total of 835 hours of gasification operation. The test campaign consisted of operation using Powder River Basin (PRB) subbituminous coal and high sodium lignite from the North Dakota Freedom mine. The highest gasifier operating temperature mostly varied from 1,760 to 1,850 F with PRB and 1,500 to 1,600 F with lignite. Typically, during PRB operations, the gasifier exit pressure was maintained between 215 and 225 psig using air as the gasification oxidant and between 145 and 190 psig while using oxygen as the oxidant. With lignite, the gasifier operated only in air-blown mode, and the gasifier outlet pressure ranged from 150 …

These notes were prepared for presentation at the Defense Threat Reduction Agency's (DTRA) Hard Target Research and Analysis Center (HTRAC), at the occasion of a short course held on June 14-15, 2004. The material is intended for analysts who must evaluate the geo-mechanical characteristics of sites of interest, in order to provide appropriate input to calculations of ground shock effects on underground facilities in rock masses. These analysts are associated with the Interagency Geotechnical Assessment Team (IGAT). Because geological discontinuities introduce scale effects on the mechanical properties of rock formations, these large-scale properties cannot be estimated on the basis of tests on small cores.

A Wolter X-ray optic was the central component of the microscope envisioned to fulfill the imaging requirements of the Characterization SI. After encountering many difficulties and delays, an optic was finally produced that, unfortunately, only partially met its specifications. With the SI halted, and efforts underway to reformulate a LDRD program to support fabrication of X-ray optics, it is useful to examine the previous effort and compile a list of lessons learned during the research.

NAFEMS was originally founded at the United Kingdom's National Engineering Laboratory as the National Agency for Finite Element Methods and Standards. It was subsequently privatized as the not-for-profit organization NAFEMS, Ltd., but retains its mission ''To promote the safe and reliable use of finite element and related technology''. That mission has been pursued in part by sponsoring a series of studies that published benchmarked deemed suitable to assess the basic accuracy of engineering simulation tools. The early studies focused on FEA for linear solid and structural mechanics and then extended to nonlinear solid mechanics, eventually including contact. These benchmarks are complemented by educational materials concerning analysis technologies and approaches. More recently NAFEMS is expanding to consider thermal-fluid problems. Further information is available at www.nafems.org. Essentially all major commercial firms selling FEA for solid mechanics are members of NAFEMS and it seemed clear that Methods Development Group should leverage from this information resource, too. In 2002, W Program ASCI funding purchased a three-year membership in NAFEMS. In the summer of 2003 the first author hosted a summer graduate student to begin modeling some of the benchmark problems. We concentrated on NIKE3D, as the benchmarks are most typically problems most naturally run …

Lawrence Livermore National Laboratory participated in a U. S. Department of Energy/Office of Industrial Technology sponsored research project 'Development of a Rolling Process Design Tool for Use in Improving Hot Roll Slab Recovery', as a Cooperative Agreement TC-02028 with the Alcoa Technical Center (ATC). The objective of the joint project with Alcoa is to develop a numerical modeling capability to optimize the hot rolling process used to produce aluminum plate. Product lost in the rolling process and subsequent recycling, wastes resources consumed in the energy-intensive steps of remelting and reprocessing the ingot. The modeling capability developed by project partners will be used to produce plate more efficiently and with reduced product loss.

Research projects supported by the program include items such as dating geological material and producing high current super conducting magnets. The funding continues to give small colleges and universities the valuable opportunity to use the NSC for teaching courses in nuclear processes; specifically neutron activation analysis and gamma spectroscopy. The Reactor Sharing Program has supported the construction of a Fast Neutron Flux Irradiator for users at New Mexico Institute of Mining and Technology and the University of Houston. This device has been characterized and has been found to have near optimum neutron fluxes for A39/Ar 40 dating. Institution final reports and publications resulting from the use of these funds are on file at the Nuclear Science Center.

The authors describe version 3.0 of the COPS set of nonlinearly constrained optimization problems. They have added new problems, as well as streamlined and improved most of the problems. They also provide a comparison of the FILTER, KNITRO, LOQO, MINOS, and SNOPT solvers on these problems.

A new analytical technique has been developed that measures both total protium (H) and deuterium (D) in a gas mixture containing H2, D2, and HD. This new analytical technique uses a micro gas chromatograph (GC) with two molecular sieve columns. One column uses D2 as the carrier gas and the other uses H2 as the carrier gas. Laboratory tests have shown that when used in this configuration the GC can measure both total protium and total deuterium, each with a sensitivity of less than 20 ppm. This new analytical technique was developed as a result of a request to provide instrumentation to measure the protium and deuterium concentrations at several process points during initial testing of the new hydrogen tritium thermal cycling absorption process columns.

This project serves to fill information gap through the development of a novel surface-enhanced Raman scattering (SERS) spectroscopy to selectively and sensitively monitor and characterize the chemical speciation of radionuclides at trace levels. The SERS technique permits both of these measurements to be made simultaneously, and results in significant improvement over current methods in reducing time of analysis, cost, and sample manipulation. Our overall goal is (a) to develop a scientific basis for this new methodology to detect radionuclides via SERS and (b) to rationally synthesize and evaluate novel sol-gel based SERS substrates tailored to sensitively detect and characterize inorganic radionuclides such as TcO{sub 4}{sup -}, actinyl ions (e.g. UO{sub 2}{sup 2+}, NpO{sub 2}{sup +}, and PuO{sub 2}{sup 2+}) and other chemical compounds of interest.

Dense nonaqueous phase liquid (DNAPL) contamination in the vadose zone is a significant problem at Department of Energy sites. Soil vapor extraction (SVE) is commonly used to remediate DNAPLs from the vadose zone. In most cases, a period of high recovery has been followed by a sustained period of low recovery. This behavior has been attributed to multiple processes including slow interphase mass transfer, retarded vapor phase transport, and diffusion from unswept zones of low permeability. Prior attempts to uncouple and quantify these processes have relied on column experiments, where the effluent concentration was monitored under different conditions in an effort to quantify the contributions from a single process. In real porous media these processes occur simultaneously and are inter-related. Further, the contribution from each of these processes varies at the pore scale and with time. This research aims to determine the pore-scale processes that limit the removal of DNAPL components in heterogeneous porous media during SVE. The specific objectives are to: (1) determine the effect of unswept zones on DNAPL removal during SVE, (2) determine the effect of retarded vapor phase transport on DNAPL removal during SVE, and (3) determine the effect of interphase mass transfer on DNAPL removal …

Reports in the Argonne National Laboratory Nuclear Data and Measurement Series present results of studies in the field of microscopic nuclear data. The primary objective of the series is the dissemination of information in the comprehensive form required for nuclear technology applications. This Series is devoted to: (a) measured microscopic nuclear parameters, (b) experimental techniques and facilities employed in measurements, (c) the analysis, correlation and interpretation of nuclear data, and (d) the compilation and evaluation of nuclear data. Contributions to this Series are reviewed to assure technical competence and, unless otherwise stated, the contents can be formally referenced. This Series does not supplant formal journal publication, but it does provide the more extensive information required for technological applications (e.g., tabulated numerical data) in a timely manner.

The Department of Energy selected CSSX as the preferred cesium removal technology for Savannah River Site waste. As a pretreatment step for the CSSX flowsheet, personnel contact the incoming salt solution that contains entrained sludge with MST to adsorb strontium and select actinides. They filter the resulting slurry to remove the sludge and MST. The filtrate receives further treatment to remove cesium in the solvent extraction system. The baseline filtration technology uses a Mott crossflow filter. We conducted pilot-scale crossflow filter testing with simulated SRS high level waste to evaluate the impact of operating parameters on the crossflow filtration process. The tests employed 0.5 micron and 0.1 micron filters. The feed slurries for these tests included simulated sludge plus MST, simulated sludge only, and simulated sludge plus manganese oxide solids. The supernate for these tests consisted of 5.6-6.4 M sodium, average salt solution. During the tests, we measured the axial pressure drop as a function of axial velocity, feed slurry, and insoluble solids concentration. This report documents the axial pressure drop data.

One of the main areas of research in the last two years in this program has been the properties of grain boundaries in perovskite and fluorite structure materials.

Budget Period 2 of the East Binger Unit (''EBU'') DOE Project has been. Recent activities included additional data gathering and project monitoring, plus initiation of work on an SPE paper on the modeling efforts of the project. Early production performance suggests horizontal wells do not provide sufficient additional production over vertical wells to justify their incremental cost. It will take more time to evaluate the impact of the horizontal wells on sweep and ultimate recovery, but it is unlikely that an improvement in recovery will be sufficient to make the overall economic value of horizontal wells greater than the economic value of vertical wells. Monitoring of overall performance of the pilot area continues. Overall response to the various projects continues to be very favorable. Injection into the pilot area has nearly doubled, while gas production and nitrogen content of produced gas have both decreased. Nitrogen recycle within the pilot area has dropped from 60% to 20%. Efforts to further disseminate knowledge gained through this project, by means of technical paper presentations to industry groups, are underway. Project monitoring and technology transfer will be focus areas of Budget Period 3.

The Linac Coherent Light Source (LCLS) undulator line will consist of 33 undulator segments separated by breaks of two different lengths. The undulator segments are 3.4-m-long permanent-magnet planar hybrid devices with a period length of 30 mm and a magnetic gap of approximately 6 mm. Focusing quadrupoles, in a FODO lattice, and electron-beam diagnostics will be located in the breaks between undulator segments. Every third break will be longer in order to also accommodate x-ray diagnostics. Thus, taking the alternating focusing and defocusing quadrupoles into account, the ''super-period'' length before the undulator line repeats itself is six undulator segments. For additional details on the LCLS project and the undulator line, please refer to the conceptual design report (CDR). A full-length prototype undulator segment has been designed, manufactured and tested, and this document provides a comprehensive report of our experience with the prototype. It contains sections on the overall design philosophy and presents many important measurements including magnetic measurements of the magnet blocks, as well as of the assembled device, and mechanical and thermal measurements. It also contains a summary section (section 5) and one section that summarizes some remaining issues being investigated (section 6).

The project aimed at the development of a Vertical Floatation melter, for application to the aluminum industry. This is intended to improve both the energy efficiency and environmental performance of aluminum melting furnaces. Phase I of this project dealt primarily with the initial research effort. Phase II, dealt with pilot-scale testing.

This year we focused on investigating the effect of particulate fines in both the hot flow and cold flow studies. This report summarizes the results of those studies in the hot flow and cold flow geometries. In the hot flow studies, increasing the fines content in the pulverized coal enhances combustion stability producing attached flames that were otherwise detached. NO{sub x} emissions are reduced by up to 50% through flame attachment. For always-attached flames, increasing the fraction of fines had little impact on total NO emissions. In the cold flow studies we found that the presence of the fine particles enhanced the velocity fluctuations of the coarse particles. The presence of coarse particles, however, did not affect the motion of the fine particles.

The underlying hypothesis of this project was that optimal alpha emitter-based radioimmunotherapy (RAIT) could be achieved by pairing the physical half-life of the radioisotope to the biological half-life of the targeting vehicle. The project had two specific aims. The first aim was to create and optimize the therapeutic efficacy of 211At-SAPS-C6.5 diabody conjugates. The second aim was to develop bispecific-targeting strategies that increase the specificity and efficacy of alpha-emitter-based RAIT. In the performance of the first aim, we created 211At-SAPS-C6.5 diabody conjugates that specifically targeted the HER2 tumor associated antigen. In evaluating these immunoconjugates we determined that they were capable of efficient tumor targeting and therapeutic efficacy of established human tumor xenografts growing in immunodeficient mice. We also determined that therapeutic doses were associated with late renal toxicity, likely due to the role of the kidneys in the systemic elimination o f these agents. We are currently performing more studies focused on better understanding the observed toxicity. In the second aim, we successfully generated bispecific single-chain Fv (bs-scFv) molecules that co-targeted HER2 and HER3 or HER2 and HER4. The in vitro kinetics and in vivo tumor-targeting properties of these molecules were evaluated. These studies revealed that the bs-scFv molecules selectively …

Conventional annular Hall thrusters become inefficient when scaled to low power. Cylindrical Hall thrusters, which have lower surface-to-volume ratio, are therefore more promising for scaling down. They presently exhibit performance comparable with conventional annular Hall thrusters. Electron cross-field transport in a 2.6 cm miniaturized cylindrical Hall thruster (100 W power level) has been studied through the analysis of experimental data and Monte Carlo simulations of electron dynamics in the thruster channel. The numerical model takes into account elastic and inelastic electron collisions with atoms, electron-wall collisions, including secondary electron emission, and Bohm diffusion. We show that in order to explain the observed discharge current, the electron anomalous collision frequency {nu}{sub B} has to be on the order of the Bohm value, {nu}{sub B} {approx} {omega}{sub c}/16. The contribution of electron-wall collisions to cross-field transport is found to be insignificant. The plasma density peak observed at the axis of the 2.6 cm cylindrical Hall thruster is likely to be due to the convergent flux of ions, which are born in the annular part of the channel and accelerated towards the thruster axis.

An experimental procedure for measuring {gamma}{sub T} has been developed and tested in two different measurements, with the {gamma}{sub T} quads on and off. The results were compared to MAD calculations. The discrepancy between the measured {gamma}{sub T} and the calculated {gamma}{sub T} is less than 5%.

Flow-acoustic interactions due to fully turbulent inflow past a shallow axisymmetric cavity mounted in a pipe, which give rise to flow tones, are investigated using a technique of high-image-density particle image velocimetry in conjunction with unsteady pressure measurements. This imaging leads to patterns of velocity, vorticity, streamline topology, and hydrodynamic contributions to the acoustic power integral. Global instantaneous images, as well as time-averaged images, are evaluated to provide insight into the flow physics during tone generation. Emphasis is on the manner in which the streamwise length scale of the cavity alters the major features of the flow structure. These image-based approaches allow identification of regions of the unsteady shear layer that contribute to the instantaneous hydrodynamic component of the acoustic power, which is necessary to maintain a flow tone. In addition, combined image analysis and pressure measurements allow categorization of the instantaneous flow patterns that are associated with types of time traces and spectra of the fluctuating pressure. In contrast to consideration based solely on pressure spectra, it is demonstrated that locked-on tones may actually exhibit intermittent, non-phase-locked images, apparently due to low damping of the acoustic resonator. Locked-on flow tones (without modulation or intermittency), locked-on flow tones with modulation, …

In order to have a standard for furnaces that includes electricity consumption or for the efficiency of furnace blowers to be determined, it is necessary to determine the airflow of a furnace or furnace blower. This study focused on airflow testing, in order to determine if an existing test method for measuring blower airflow could be used to measure the airflow of a furnace, under conditions seen in actual installations and to collect data and insights into the operating characteristics of various types of furnace blowers, to use in the analysis of the electricity consumption of furnaces. Results of the measured airflow on furnaces with three types of blower and motor combinations are presented in the report. These included: (1) a forward-curved blower wheel with a typical permanent split capacitor (PSC) motor, (2) a forward-curved blower wheel with an electronically-commutated motor (ECM), and (3) a prototype blower, consisting of a backward-inclined blower wheel matched to an ECM motor prototype, which is being developed as an energy-saving alternative to conventional furnace blowers. The testing provided data on power consumption, static and total pressure, and blower speed.

Conventional annular Hall thrusters become inefficient when scaled to low power. Cylindrical Hall thrusters, which have lower surface-to-volume ratio, are therefore more promising for scaling down. They presently exhibit performance comparable with conventional annular Hall thrusters. Electron cross-field transport in a 2.6 cm miniaturized cylindrical Hall thruster (100 W power level) has been studied through the analysis of experimental data and Monte Carlo simulations of electron dynamics in the thruster channel. The numerical model takes into account elastic and inelastic electron collisions with atoms, electron-wall collisions, including secondary electron emission, and Bohm diffusion. We show that in order to explain the observed discharge current, the electron anomalous collision frequency {nu}{sub B} has to be on the order of the Bohm value, {nu}{sub B} {approx} {omega}{sub c}/16. The contribution of electron-wall collisions to cross-field transport is found to be insignificant.

This document is the collaborative effort of the members of an ad hoc subcommittee of the Underground Test Area (UGTA) Technical Working Group (TWG). The UGTA Project relies on data from a variety of sources; therefore, a process is needed to identify relevant factors for determining whether material-property data collected from other areas can be used to support groundwater flow, radionuclide transport, and other models within a Corrective Action Unit (CAU), and for documenting the data transfer decision and process. This document describes the overall data transfer process. Separate Parameter Descriptions will be prepared that provide information for selected specific parameters as determined by the U.S. Department of Energy (DOE) UGTA Project Manager. This document and its accompanying appendices do not provide the specific criteria to be used for transfer of data for specific uses. Rather, the criteria will be established by separate parameter-specific and model-specific Data Transfer Protocols. The CAU Data Documentation Packages and data analysis reports will apply the protocols and provide or reference a document with the data transfer evaluations and decisions.