We have developed a new tool for ultrahigh-pressure research at LLL. This system, which we call the electric gun, has already achieved thin flyer plate velocities in excess of 20 km/s and pressures of the order of 2 TPa in tantalum. We believe that the electric gun is competitive with laser- and nuclear-driven methods of producing shocks in the 1-to-5 TPa range because of its precision and ease and economy of operation. Its development is recommended for shock initiation studies, dry runs for Site 300 hydroshots, and as a shock wave generator for surface studies.

This paper describes the design and fabrication of a unique silicon substrate with which laser-target components can be mass produced. Different sizes and shapes of gold foils from 50 to 3000 microns in diameter and up to 25 microns thick have been produced with this process since 1976.

A feasibility study was made of the hydroelectric power potential at Broadwater Dam in western Montana. Two alternative configurations for the potential project were evaluated and the economics of four possible sources of project funding were assessed. The configurations analyzed were an apron-mounted configuration, in which the turbine-generator units are located on the downstream apron of the existing dam, and a conventional configuration, in which the units are located in a new powerhouse adjacent to the existing dam. The funding sources considered were the Department of Energy loan program, the United States Bureau of Reclamation PL-984 loan program and conventional revenue bonds, both taxable and tax-exempt. The optimal project alternative was determined to be the apron-mounted configuration. The final choice of funding would be dependent on the power purchaser. It was shown that, regardless of the configuraton or funding source selected, the project would be feasible. The cost of the apron-mounted configuration, which would consist of four turbine-generator units for a total installed capacity of 9.76 MW, was estimated as $13,250,000 with financing provided by either a PL-984 loan or tax-exempt bonds. The cost per installed kilowatt was therefore $1,350, and the cost per kilowatt-hour was 19.6 mills. The average …

New laboratory data are reported on the effect of confining (lithostatic) pressure, pore-water pressure, and principal stress difference on permeability of Westerly granite and White Lake gneissic granite. Permeabilities as low as 10/sup -19/ cm/sup 2/ (10/sup -11/ D) have been measured successfully, using a transient technique. Principal strains, electrical conductivity, and compressional velocity are determined simultaneously. Applied loads on the 15-cm diameter by 28-cm long test sample are controlled automatically and all data are taken by a microcomputer. Results on the gneissic granite indicate permeabilities of 10/sup -18/ to 10/sup -19/ cm/sup 2/ that appear to be unaffected either by effective pressure or by stress. The granite yields permeabilities of 4x10/sup -16/ cm/sup 2/ that decrease by a factor of two with pressure and vary by a factor of two with stress. When compared to the initial value, compressional velocities increase by 4% and conductivity decreases by 50% as pressure is increased to 50 MPa in the gneissic granite. In granite, these become 3% and 58%, respectively. At pressure, loading of the granite of 0.5 of failure stress increases conductivity by about 20%.

It was shown that by controlling the sputtering preparation conditions of noncrystalline Ge films the surface microstructure can be drastically altered by simply etching in 30% H/sub 2/O/sub 2/. The resulting surface has a total reflectance of less than 3% in the solar spectrum. This flat-black surface appearance is shown to be due to a dense array of aligned, needle-like protrusions which have an extremely high aspect ratio and both a cross-sectional area and a separation between needles on the order of the wavelength of solar radiation. A systematic series of thin films were prepared by rf-sputtering with rf-power and Ar gas pressure as the primary preparation parameters and characterizing the various films.

A unique model of fusion product (fp) slowing down and thermalization in field-reversed mirror (FRM) plasmas has been developed. It couples the Hill's spherical vortex representation of a field-reversed equilibrium with a monte carlo treatment of coulomb scattering, and thus provides a complete picture of fps from birth through their thermal diffusion. The incorporation of drag and scattering effects allows the code to address both the energy deposition and the ash buildup question. Results of several test cases are presented along with selected results from FRM studies.

None

Experiments have been performed with a 125-kJ plasma focus to investigate mechanisms for rapid coupling of inductively-stored energy into plasmas. The coupling can take place through the formation of an electron or ion beam that deposits its energy in a target or directly by the penetration of the magnetic field into a resistive plasma. Some preliminary results from experiments of both types are described. The experiments use a replaceable conical anode tip that is intended to guide the focus to within a few millimeters of the axis, where it can suddenly deliver energy either to a small target or to particles that are accelerated. X-ray and fast-ion diagnostics have been used to study the effects.