None

None

We present the first evidence of charmless decays of the B{sub s}{sup 0} meson, the decay B{sub s}{sup 0} {yields} {phi}{phi}, and a measurement of the Branching Ratio BR(B{sub s}{sup 0} {yields} {phi}{phi}) using 180 pb{sup -1} of data collected by the CDF II experiment at the Fermilab Tevatron collider. In addition, the BR and direct CP asymmetry for the B{sup +} {yields} {phi}K{sup +} decay are measured.

Significant work has been done by the investigators on the cerium oxide-copper oxide based sorbent/catalysts for the combined removal of sulfur and nitrogen oxides from the flue gases of stationary sources. A relatively wide temperature window was established for the use of alumina-supported cerium oxide-copper oxide mixtures as regenerable sorbents for SO{sub 2} removal. Preliminary evaluation of these sorbents as catalysts for the selective reduction of NO{sub x} gave promising results with ammonia, but indicated low selectivity when methane was used as the reductant. Since the replacement of ammonia by another reductant is commercially very attractive, in this project, four research components will be undertaken. The investigation of the reaction mechanism, the first component, will help in the selection of promoters to improve the catalytic activity and selectivity of the sorbents in the SCR with methane. This will result in new catalyst formulations (second component). If this research is successful, the combined SO{sub 2}-NO{sub x} removal process based on alumina-supported copper oxide-ceria sorbent/catalysts will become very attractive for commercial applications. The objective of the third component of the project is to develop an alternative SCR process using another inexpensive fuel, residual fuel oil, instead of natural gas. This innovative proposal …

The primary motivation for this set of research activities was to develop a foundation in several aspects of power in order to position Cleveland State University to lead a multiuniversity effort to secure funding for enhanced power system projects and to be able to eventually secure a NASA Space Power Systems Center status through the competitive bidding process. This was accomplished by focusing on these major project areas, (1) the design of the next generation nuclear-electric power generation system, (2) the design of a distributed, fault-tolerant, and modular power system, and (3) the development of the dynamics and control of active magnetic bearings for flywheel energy storage without using conventional sensors.

In light water reactors (LWRs), vessel internal components made of nickel-base alloys are susceptible to environmentally assisted cracking. A better understanding of the causes and mechanisms of this cracking may permit less conservative estimates of damage accumulation and requirements on inspection intervals. A program is being conducted at Argonne National Laboratory to evaluate the resistance of Ni alloys and their welds to environmentally assisted cracking in simulated LWR coolant environments. This report presents crack growth rate (CGR) results for Alloy 182 shielded-metal-arc weld metal in a simulated pressurized water reactor (PWR) environment at 320 C. Crack growth tests were conducted on 1-T compact tension specimens with different weld orientations from both double-J and deep-groove welds. The results indicate little or no environmental enhancement of fatigue CGRs of Alloy 182 weld metal in the PWR environment. The CGRs of Alloy 182 in the PWR environment are a factor of {approx}5 higher than those of Alloy 600 in air under the same loading conditions. The stress corrosion cracking for the Alloy 182 weld is close to the average behavior of Alloy 600 in the PWR environment. The weld orientation was found to have a profound effect on the magnitude of crack growth: …

This report summarizes the progress made during the August 1, 2006 - May 31, 2008 award period under Cooperative Agreement DE-FC26-05NT42614 for the U. S. Department of Energy/National Energy Technology Laboratory (USDOE/NETL) entitled 'SECA Coal Based Systems'. The initial overall objective of this program was to design, develop, and demonstrate multi-MW integrated gasification fuel cell (IGFC) power plants with >50% overall efficiency from coal (HHV) to AC power. The focus of the program was to develop low-cost, high performance, modular solid oxide fuel cell (SOFC) technology to support coal gas IGFC power systems. After a detailed GE internal review of the SOFC technology, the program was de-scoped at GE's request. The primary objective of this program was then focused on developing a performance degradation mitigation path for high performing, cost-effective solid oxide fuel cells (SOFCs). There were two initial major objectives in this program. These were: (1) Develop and optimize a design of a >100 MWe integrated gasification fuel cell (IGFC) power plant; (2) Resolve identified barrier issues concerning the long-term economic performance of SOFC. The program focused on designing and cost estimating the IGFC system and resolving technical and economic barrier issues relating to SOFC. In doing so, manufacturing …

LiFePO{sub 4} has several potential advantages in comparison to the transition metal oxide cathode materials used in commercial lithium-ion batteries. However, its low intrinsic electronic conductivity ({approx} 10{sup -9} S/cm) is problematic. We report here a study by soft x-ray absorption/emission spectroscopy of the electronic properties of undoped LiFePO{sub 4} and Li-doped LiFePO{sub 4} in which Li{sup +} ions are substituted for Fe{sup 2+} ions in an attempt to increase the intrinsic electronic conductivity. The conductivities of the Li{sub 1+x}Fe{sub 1-x}PO{sub 4} samples were, however, essentially unchanged from that of the undoped LiFePO{sub 4}. Nonetheless, evidence for changing the electronic properties of LiFePO{sub 4} by doping with excess Li+ was observed by the XAS/XES spectroscopy. New pre-edge features the O-1s XAS spectrum of Li{sub 1.05}Fe{sub 0.95}PO4 is a direct indication that the charge compensation for substitution of Fe{sup 2+} by Li{sup +} resides in the unoccupied O-2p orbitals. A charge transfer (CT) excitation was also observed in the doped material implying that the unoccupied O-2p orbitals created by doping are strongly hybridized with unoccupied Fe-3d orbitals of neighboring sites. However, the strong covalent bonding within the (PO{sub 4}){sup 3-} anions and the large separation of the Fe cations means that …

Two new positron active isotopes, B{sup 8} and Na{sup 20}, have been found to decay to excited states of Be{sup 8} and Ne{sup 20}, which in turn decay 'instantaneously' by alpha emission. Their half-lives are 0.65 {+-} 0.1 sec. and 1/4 sec. respectively. N{sup 12} is also found to have a low energy positron group which leads to an {alpha}-unstable excited state in C{sup 12}. The masses of B{sup 8} and Na{sup 20} are 8.027 and 20.015 respectively. B{sup 8} decays by a 13.7 {+-} 0.3 Mev positron, through the same excited state of Be{sup 8} as does Li{sup 8}. Estimates of the energies of the excited state in C{sup 12} and Ne{sup 20} are made.

The original goal of this program was the identification and design of new noble-metal-based catalysts for the selective catalytic reduction of nitric oxide by hydrocarbons under excess oxygen (i.e., ''lean'') conditions (HC-SCR). Work conducted in the first funding cycle of this award (i.e., 1997-2000) was successful in allowing us to develop an understanding of the fundamental surface chemistry taking place during the adsorption and reaction of nitrogen oxides and propylene on the surface of supported noble metal catalysts. Both experimental results collected in our own group as well as molecular simulation results published by Professor Neurock suggested that in order to improve the performance of the Pt catalysts--in terms of the nitrogen selectivity and the temperature window of operation-- it was necessary to introduce a second metal. However, synthesizing such catalysts with the metals of interest (i.e., Pt-Au, Pt-Ru, Pt-Rh, etc.) with some degree of control of the structure and composition of the resulting supported metal particles is in itself a research challenge. Consequently, the bulk of our efforts during the second funding cycle of this award (covered by this report) was shifted to the use of organometallic cluster precursors for the synthesis on novel bimetallic catalysts. During this time …

This study, supported by the US Department of Energy, Wind Powering America Program, Maryland Department of Natural Resources and Chesapeake Bay Foundation, analyzed barriers to wind energy development in the Mid-Atlantic region along with options for overcoming or mitigating them. The Mid-Atlantic States including Delaware, Maryland, North Carolina and Virginia, have excellent wind energy potential and growing demand for electricity, but only two utility-scale projects have been installed to date. Reasons for this apathetic development of wind resources were analyzed and quantified for four markets. Specific applications are: 1) Appalachian mountain ridgeline sites, 2) on coastal plains and peninsulas, 3) at shallow water sites in Delaware and Chesapeake Bays, Albemarle and Pamlico Sounds, and 4) at deeper water sites off the Atlantic coast. Each market has distinctly different opportunities and barriers. The primary barriers to wind development described in this report can be grouped into four categories; state policy and regulatory issues, wind resource technical uncertainty, economic viability, and public interest in environmental issues. The properties of these typologies are not mutually independent and do interact. The report concluded that there are no insurmountable barriers to land-based wind energy projects and they could be economically viable today. Likewise potential sites …

This report contains discussions on the following topics: Experimental program at the Fermilab Tevatron Collider: FNAL E-740; Experimental program at the superconducting super collider: Solenoidal detector collaboration; Computation development program at Iowa State University: Batch after twilight running and parallel processing; Experimental program at the University of Hawaii: Deep underwater muon and neutrino detector; Global analysis of parton distributions; high energy direct photon production; photon fragmentation functions; single transverse-spin asymmetry; associated production of Higgs Boson at collider energies; Cronin effect in photoproduction and deeply inelastic scattering; and heavy meson production.

A parameter study was performed to examine the (shock) damage obtained with long-rod and spherical mono-material penetrators impacting two varieties of limestone. In all cases, the impacts were assumed to be normal to the plane of the rock and at zero angle of attack (in the case of the rods). Impact velocities ranged to 15 km/s but most calculations were performed at 4 and 6 km/s and the penetrator mass was fixed at 1000 kg. For unlined underground structures, incipient damage was defined to occur when the peak stress, {sigma}{sub pk}, exceeds 1 kb (100 MPa) and the applied impulse per unit area, I{sub pk}, exceeds 1 ktap (1 kb-{micro}s). Severe damage was assumed to occur when {sigma}{sub pk} exceeds 1 kb and I{sub pk} exceeds 1000 ktaps. Using the latter definition it was found that severe damage in hard, non-porous limestone with spherical impactors extended to a depth of 9 m on-axis for an impact velocity of 4 km/s and 12 m at 6 km/s. Cylinders with length-to-diameter (L/D) ratio of 8.75 achieved depth to severe damage of 23 m and 40 m, respectively under the same conditions. For a limestone medium with 2% initial gas porosity, the latter …

ABETI/IWESS is a project carried out by Carnegie Mellon's Center for Building Performance and Diagnostics, the CBPD, supported by the U.S. Department of Energy/EERE, to design, procure, install, operate, and evaluate an energy supply system, an ESS, that will provide power, cooling, heating and ventilation for CBPD's Intelligent Workplace, the IW. The energy sources for this system, the IWESS, are solar radiation and bioDiesel fuel. The components of this overall system are: (1) a solar driven cooling and heating system for the IW comprising solar receivers, an absorption chiller, heat recovery exchanger, and circulation pump; (2) a bioDiesel fueled engine generator with heat recovery exchangers, one on the exhaust to provide steam and the other on the engine coolant to provide heated water; (3) a ventilation system including an enthalpy recovery wheel, an air based heat pump, an active desiccant wheel, and an air circulation fan; and (4) various convective and radiant cooling/heating units and ventilation air diffusers distributed throughout the IW. The goal of the ABETI/IWESS project is to demonstrate an energy supply system for a building space that will provide a healthy, comfortable environment for the occupants and that will reduce the quantity of energy consumed in the …

This report documents the findings of an on-site audit of the U.S. Customs Cargo Inspection Facility (CIF) in Detroit, Michigan. The federal landlord for this building is the General Services Administration (GSA). The focus of the audit was to identify various no-cost or low-cost energy-efficiency opportunities that, once implemented, would reduce electrical and gas consumption and increase the operational efficiency of the building. This audit also provided an opportunity to identify potential capital cost projects that should be considered in the future to acquire additional energy (electric and gas) and water savings to further increase the operational efficiency of the building.

This report documents the findings from an onsite audit of the John W. Bricker Federal building located in Columbus, Ohio. The Federal landlord for this building is the General Services Administration (GSA). The focus of the audit was to identify various no-cost or low-cost energy efficiency opportunities that, once implemented, would either reduce electrical and gas consumption or increase the operational efficiency of the building. This audit also provided an opportunity to identify potential capital cost projects that should be considered in the future to acquire additional energy (electric and gas) and water savings to further increase the operational efficiency of the building.

To reduce the effect of global warming on our climate, the levels of CO{sub 2} emissions should be reduced. One way to do this is to increase the efficiency of electricity production from fossil fuels. This will in turn reduce the amount of CO{sub 2} emissions for a given power output. Using US practice for efficiency calculations, then a move from a typical US plant running at 37% efficiency to a 760 C /38.5 MPa (1400 F/5580 psi) plant running at 48% efficiency would reduce CO2 emissions by 170kg/MW.hr or 25%. This report presents a literature review and roadmap for the materials development required to produce a 760 C (1400 F) / 38.5MPa (5580 psi) steam turbine without use of cooling steam to reduce the material temperature. The report reviews the materials solutions available for operation in components exposed to temperatures in the range of 600 to 760 C, i.e. above the current range of operating conditions for today's turbines. A roadmap of the timescale and approximate cost for carrying out the required development is also included. The nano-structured austenitic alloy CF8C+ was investigated during the program, and the mechanical behavior of this alloy is presented and discussed as an …

The Physics Section vacuum deposition system is available for several types of thin film techniques. This vacuum evaporation system operates in the high vacuum range. The evaporation source is a resistive heating element, either a boat or a filament design. Coating is then line of sight from the source. Substrates to be coated can have a maximum diameter of 17 inches. At this time the variations in the thickness of the coatings can be controlled, by monitor, to within about 100 angstroms. The system diagrams follow the Operation Procedures and the Sample Coating Procedures provided in this document. 3 figs.

This is the University of California, Radiation Laboratory monthly progress report for May 1948. It discusses the following: (1) 184-inch Cyclotron Program; (2) 60-inch Cyclotron Program; (3) Synchrotron Program; (4) Linear Accelerator Program; (5) Experimental Physics; (6) Theoretical Physics, (7) Isotope Separation Program; (8) Chemistry Departments; (9) Medical Physics; and (10) Health Physics and Chemistry.

Argonne National Laboratory founded the Laboratory Computing Resource Center (LCRC) in the spring of 2002 to help meet pressing program needs for computational modeling, simulation, and analysis. The guiding mission is to provide critical computing resources that accelerate the development of high-performance computing expertise, applications, and computations to meet the Laboratory's challenging science and engineering missions. In September 2002 the LCRC deployed a 350-node computing cluster from Linux NetworX to address Laboratory needs for mid-range supercomputing. This cluster, named 'Jazz', achieved over a teraflop of computing power (10{sup 12} floating-point calculations per second) on standard tests, making it the Laboratory's first terascale computing system and one of the 50 fastest computers in the world at the time. Jazz was made available to early users in November 2002 while the system was undergoing development and configuration. In April 2003, Jazz was officially made available for production operation. Since then, the Jazz user community has grown steadily. By the end of fiscal year 2006, there were 76 active projects on Jazz involving over 380 scientists and engineers. These projects represent a wide cross-section of Laboratory expertise, including work in biosciences, chemistry, climate, computer science, engineering applications, environmental science, geoscience, information science, materials …

Your Genes, Your Choices provides accurate information about the ethical, legal, and social implications of the Human Genome Project and genetic research in an easy-to-read style and format. Each chapter in the book begins with a brief vignette, which introduces an issue within a human story, and raises a question for the reader to think about as the basic science and information are presented in the rest of the chapter.

Pilot plant experiments are described in which trichloroethylene was used for the reduction of uranium hexafluoride to uranium tetrafluoride. After unsatisfactory preliminary results with liquid phase reduction, satisfactory results were obtained with a vapor phase reduction system. It was found that vapor phase reduction at approximately 450 deg F, produced a low density product which contained only small quantities of uranium(VI); sintering the uranium tetrafluoride in a hydrogen fluoride atmosphere increased the product density to approximately 3 g/cc. The reduction was essentially complete, and the effluent gas contained less than 1 ppm of uranium hexafluoride. The purity of the uranium tetrafluoride produced was equivalent to that of the uranium hexafluoride used as feed. A complete discussion is given of the operation of the various parts of the system. (auth)

None

The stack sampling system at the 325 Building (Radiochemical Processing Laboratory [RPL]) was constructed to comply with the American National Standards Institute’s (ANSI’s) Guide to Sampling Airborne Radioactive Materials in Nuclear Facilities (ANSI N13.1-1969). This standard provided prescriptive criteria for the location of radionuclide air-sampling systems. In 1999, the standard was revised (Sampling and Monitoring Releases of Airborne Radioactive Substances From the Stacks and Ducts of Nuclear Facilities [ANSI/Health Physics Society [HPS] 13.1-1999]) to provide performance-based criteria for the location of sampling systems. Testing was conducted for the 325 Building stack to determine whether the sampling system would meet the updated criteria for uniform air velocity and contaminant concentration in the revised ANSI/HPS 13.1-1999 standard under normal operating conditions (Smith et al. 2010). Measurement results were within criteria for all tests. Additional testing and modeling was performed to determine whether the sampling system would meet criteria under set-back flow conditions. This included measurements taken from a scale model with one-third of the exhaust flow and computer modeling of the system with two-thirds of the exhaust flow. This report documents the results of the set-back flow condition measurements and modeling. Tests performed included flow angularity, uniformity of velocity, gas concentration, and …