The A2 LITE is a 2 liter, 2000 MPa, 750 K ultra-high pressure (UHP) vessel used to demonstrate UHP technology and to provide an air flow for wind tunnel nozzle development. It is the largest volume UHP vessel in the world. The design is based on a 100:1 pressure intensification using a hydraulic ram as a low pressure driver and a three-layer compound cylinder UHP section. Active control of the 900 mm piston stroke in the 63.5 mm bore permits pressure-time profiles ranging from static to constant pressure during flow through a 1 mm throat diameter nozzle for 1 second.

This report presents the details of the auger sampling events for underground waste tank C-111. The samples were shipped to the 222-S laboratories were they underwent safety screening analysis and primary ferricyanide analysis. The samples were analyzed for alpha total, total organic carbon, cyanide, Ni, moisture, and temperature differentials. The results of this analysis are presented in this document.

The purpose of this report is to provide a brief description of the sampling approaches, a description of the samples collected, and the results for the Fall 2005 sampling event. This report presents the methods and results of the work to support the 100 Area and 300 Area Component of the River Corridor Baseline Risk Assessment.

None

Spin physics in the past has provided an acid test of many models and theories and over the last decade has revealed new and unexpected phenomena to confront present day theories. This work received great impetus from the experiments at the ZGS, where for the first time multi-GeV polarized beams became available. This, in conjunction with polarized targets, allowed the complete specification of the initial quantum states in high energy proton-proton interactions and led to many startling new results. Although spin effects were important at the previously measured lower energies, practically all theorists felt that spin effects would become negligible at higher energies. Instead, the ZGS results showed in many cases even larger effects than those observed at lower energies. By the time the ZGS was shut down in 1979, high energy polarized proton projects were planned for KEK in Japan, SATURNE in France, and the AGS at Brookhaven. At present, serious thought is being given to high energy polarized proton beams at Fermilab, CERN, and indeed in planning for the Superconducting Super Collider. Today, I would like to describe the facility at Brookhaven and give you the present status of the project. We have been in the commissioning phase …

The overall objective of the acceptance test is to demonstrate a combined system. This includes associated tools and equipment necessary to perform cleaning in the 105 K East Basin (KE) for achieving optimum reduction in the level of contamination/dose rate on canisters prior to removal from the KE Basin and subsequent packaging for disposal. Acceptance tests shall include necessary hardware to achieve acceptance of the cleaning phase of canisters. This acceptance test procedure will define the acceptance testing criteria of the high pressure water jet cleaning fixture. The focus of this procedure will be to provide guidelines and instructions to control, evaluate and document the acceptance testing for cleaning effectiveness and method(s) of removing the contaminated surface layer from the canister presently identified in KE Basin. Additionally, the desired result of the acceptance test will be to deliver to K Basins a thoroughly tested and proven system for underwater decontamination and dose reduction. This report discusses the acceptance test procedure for the High Pressure Water Jet.

The purpose of this test procedure is to verify that the system(s) procured to load the SY-101 Mitigation Test Pump package fulfills its functional requirements. It will also help determine the man dose expected due to handling of the package during the actual event. The scope of this procedure focuses on the ability of the air pallets and container saddles to carry the container package from the new 100 foot concrete pad into 2403-WD where it will be stored awaiting final disposition. This test attempts to simulate the actual event of depositing the SY-101 hydrogen mitigation test pump into the 2403-WD building. However, at the time of testing road modifications required to drive the 100 ton trailer into CWC were not performed. Therefore a flatbed trailer will be use to transport the container to CWC. The time required to off load the container from the 100 ton trailer will be recorded for man dose evaluation on location. The cranes used for this test will also be different than the actual event. This is not considered to be an issue due to minimal effects on man dose.

None

The purpose of this report is to help achieve the overall program goals for the development of thermo-electric modules to be incorporated in reactor or isotope space-vehicle power systems, a series of design objectives was specified.

Numerous reports have indicated that contamination at DOE facilities is widespread and pervasive. Existing technology is often too costly or ineffective in remediating these contamination problems. An effective method to address one class of contamination, petroleum hydrocarbons, is in situ bioremediation. This project was designed to provide tools and approaches for increasing the reliability of in situ bioremediation. An example of the recognition within DOE for developing these tools is in the FY-1995 Technology Development Needs Summary of the Office of Technology Development of the US DOE. This document identifies specific needs addressed by this research. For example, Section 3.3 Need Statement IS-3 identifies the need for a {open_quotes}Rapid method to detect in situ biodegradation products.{close_quotes} Also, BW-I identifies the need to recognize boundaries between clean and contaminated materials and soils. Metabolic activity could identify these boundaries. Measuring rates of in situ microbial activity is critical to the fundamental understanding of subsurface microbiology and in selecting natural attenuation as a remediation option. Given the complexity and heterogeneity of subsurface environments, a significant cost incurred during bioremediation is the characterization of microbial activity, in part because so many intermediate end points (biomass, gene frequency, laboratory measurements of activity, etc.) must be …

This report presents the 1999 calendar year update of the Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL Air Emission Inventory documents sources and emissions of nonradionuclide pollutants from operations at the INEEL. The report describes the emission inventory process and all of the sources at the INEEL, and provides nonradionuclide emissions estimates for stationary sources.

This fact sheet discusses how an air-source heat pump can heat and cool a home, as well how to select, install, operate, and maintain one.

High voltage (HV) insulators are critical components in high-energy, accelerator and pulsed power systems that drive diverse applications in the national security, nuclear weapons science, defense and industrial arenas. In these systems, the insulator may separate vacuum/non-vacuum regions or conductors with high electrical field gradients. These insulators will often fail at electric fields over an order of magnitude lower than their intrinsic dielectric strength due to flashover at the dielectric interface. Decades of studies have produced a wealth of information on fundamental processes and mechanisms important for flashover initiation, but only for relatively simple insulator configurations in controlled environments. Accelerator and pulsed power system designers are faced with applying the fundamental knowledge to complex, operational devices with escalating HV requirements. Designers are forced to rely on “best practices” and expensive prototype testing, providing boundaries for successful operation. However, the safety margin is difficult to estimate, and system design must be very conservative for situations where testing is not practicable, or replacement of failed parts is disruptive or expensive. The Phase I program demonstrated the feasibility of developing an advanced code for modeling insulator breakdown. Such a code would be of great interest for a number of applications, including high energy …

In this paper we study the validity of coupling impedance bench measurements for distributed impedances, comparing the commonly used log formula to the result obtained applying a modified version of Bethe's theory of diffraction to a long slot in a coaxial beam pipe. The equations found provide a quantitative expression for the influence of the wire thickness used in the measurement of the real and imaginary part of the longitudinal impedance. The precision achievable in an actual measurement is therefore discussed. The method presented has also been applied in the presence of lumped impedances [1].

The purpose of this analysis is to propose and qualify a design of the tie-down system for the High Level Waste (HLW) pump/agitator transport container.

None

The purpose of the Cooperative Research and Development Agreement (CRADA) between Martin Marietta Energy Systems, Inc., and Delta Frangible Ammunition (DFA), was to identify and evaluate composite materials for the development of small arms ammunition. Currently available small arms ammunition utilizes lead as the major component of the projectile. The introduction of lead into the environment by these projectiles when they are expended is a rapidly increasing environmental problem. At certain levels, lead is a toxic metal to the environment and a continual health and safety concern for firearm users as well as those who must conduct lead recovery operations from the environment. DFA is a leading supplier of high-density mixtures, which will be used to replace lead-based ammunition in specific applications. Current non-lead ammunition has several limitations that prevent it from replacing lead-based ammunition in many applications (such as applications that require ballistics, weapon recoil, and weapon function identical to that of lead-based ammunition). The purpose of the CRADA was to perform the research and development to identify cost-effective materials to be used in small arms ammunition that eventually will be used in commercially viable, environmentally conscious, non-lead, frangible and/or non-frangible, ammunition.

This report provides research highlights from the Advanced Photon Source (APS). Although these highlights represent less than 10% of the published work from the APS in 2007, they give a flavor of the diversity and impact of user research at the facility. In the strategic planning the aim is to foster the growth of existing user communities and foresee new areas of research. This coming year finds the APS engaged in putting together, along with the users, a blueprint for the next five years, and making the case for a set of prioritized investments in beamlines, the accelerator, and infrastructure, each of which will be transformational in terms of scientific impact. As this is written plans are being formulated for an important user workshop on October 20-21, 2008, to prioritize strategic plans. The fruit from past investments can be seen in this report. Examples include the creation of a dedicated beamline for x-ray photon correlation spectroscopy at Sector 8, the evolution of dedicated high-energy x-ray scattering beamlines at sectors 1 and 11, a dedicated imaging beamline at Sector 32, and new beamlines for inelastic scattering and powder diffraction. A single-pulse facility has been built in collaboration with Sector 14 (BioCARS) …

Included herein is a historical record of the AAF sponsored NEPA Project during the period of October 1945, to the present time, and covers in narrative form the nature of planning leading to the implementation of the project, the establishment of the operating group and its relationship to the Manhattan District (later to become the Atomic Energy Commission) and the approach to applicable technological problems bearing on both nuclear science and aeronautical propulsion engineering aspects.

The objective of this research is to assist the recovery of non contacted oil from known reservoirs on the Outer Continental Shelf in the Gulf of Mexico. History matching and prediction runs have been completed on the B-35-K reservoir, history matching has been completed on the B-65-G reservoir and on Reservoir 3. Modifications to BOAST II and MASTER consisted of developing codes to handle steeply dipping oil reservoirs and a radial grid format for near wellbore studies. Modifications for steeply dipping reservoirs have been successfully implemented and tested against commercial simulators in the PC version of BOAST II, renamed BOAST III. At present, modifications to BOAST II for radial grid systems are producing acceptable results in a 2-D model. A paper was presented at the 1994 ACM Symposium on Applied Computing in Phoenix, Arizona, March 6--8, 1994 on these results. Modifications have also been successfully implemented in the MASTER simulator. It is presently undergoing industry testing for validity. Laboratory investigations continued but were slowed by several unforeseen incidences involving broken apparatus and inability to receive parts due to the California earthquake. Predictive models for undeveloped oil and immiscible/miscible processes began. The methodology for determination of undeveloped potential has been completed. …

ITN's three year project Atmospheric Pressure Chemical Vapor Deposition (APCVD) of CdTe for High Efficiency Thin Film PV Devices has the overall objectives of improving thin film CdTe PV manufacturing technology and increasing CdTe PV device power conversion efficiency. CdTe deposition by APCVD employs the same reaction chemistry as has been used to deposit 16% efficient CdTe PV films, i.e., close spaced sublimation, but employs forced convection rather than diffusion as a mechanism of mass transport. Tasks of the APCVD program center on demonstration of APCVD of CdTe films, discovery of fundamental mass transport parameters, application of established engineering principles to the deposition of CdTe films, and verification of reactor design principles which could be used to design high throughput, high yield manufacturing equipment. Additional tasks relate to improved device measurement and characterization procedures that can lead to a more fundamental understanding of CdTe PV device operation and ultimately to higher device conversion efficiency and greater stability. Under the APCVD program, device analysis goes beyond conventional one-dimensional device characterization and analysis toward two dimension measurements and modeling. Accomplishments of the second year of the APCVD subcontract include: deposition of the first APCVD CdTe; identification of deficiencies in the first generation …

During the B0 Overpass construction for the CDF detector at Fermilab, 33 B1 magnets were measured using a bucked tangential coil. Measurements were made on the midplane, at the centerline and at {+-} 1 inch horizontal displacement. Since the coil was only 62 inches long, measurements were made at four longitudinal positions. Because of the design of the Main Ring, it was sufficient to combine data from all positions and report the harmonic spectrum for the magnet as a whole. For modeling the Scrounge-atron, it is more useful to treat each measurement position separately. The author reports here an analysis of the harmonic spectra at each probe position, based on the original data.

We present a study of the single-bunch beam break up (BBU) instability for a proposed x-ray facility, based on a recirculating linac, to be built in Berkeley. The effects of injection errors, both position and angle, and of misalignments in the linac are investigated. We propose possible methods for limiting the consequent emittance increase.

Ion induced beam instability is one critical issue for the electron damping ring of the International Linear Collider (ILC) due to its ultra small emittance of 2 pm. The beam ion instability with various beam filling patterns for the latest lattice DTC02 is studied using PIC code. The code has been benchmarked with SPEAR3 experimental data and there is a good agreement between the simulation and observations. It uses the optics from MAD and can handle arbitrary beam filling pattern and vacuum. Different from previous studies, multi-gas species and exact beam filling patterns have been modeled simultaneously in the study. This feature makes the study more realistic. Analyses have been done to compare with the simulations.