The shower counter system of the SLAC-LBL Mark II detector is a large lead/liquid argon system of the type pioneered by Willis and Radekal; however, it differs in most details and is much larger than other such detectors currently in operation, It contains, for example, 8000 liters of liquid argon and 3000 channels of low noise electronics, which is about eight times the size of the system of Willis et al. in the CERN ISR. This paper reports, with little reference to design, on the operation and performance of the Mark II system during approximately a year and a half of operation at the Stanford Linear Accelerator Center's e{sup +}-e{sup -} facility, SPEAR. The design and construction of the system have previously been described and a detailed discussion of all aspects -- design, construction, operation, and performance -- is in preparation.

We present a study of the decay properties of charmed D mesons produced near the peak of the {psi}" (3770) resonance in e{sup +}e{sup -} annihilation. Branching fractions for nine Cabibbo-favored and three Cabibbo-suppressed decay modes are presented along with upper limits on one additional Cabibbo-favored and four additional Cabibbo-suppressed decay modes. A study of K{pi}{pi} decay mode Dalitz plots reveals a large quasi-two-body pseudoscalar-vector component for the D{sup 0} decays and an apparent nonuniform population an the Dalitz plot for the D{sup +} decay into K{sup -}{pi}{sup +}{pi}{sup +}. Using tagged events, we measure the charged particle multiplicity and strange particle content of D decays. A measurement of the D{sup +} and D{sup 0} semileptonic decay fractions indicates that the D{sup +} has a significantly longer lifetime than the D{sup 0}.

This conference paper describes the electronic properties of ZnO/CdS/Cu(In,Ga)Se2 (CIGS)/Mo/SLG polycrystalline thin-film solar cells with compositions ranging from Cu-rich to In-rich were investigated by deep level transient spectroscopy and capacitance-voltage (C-V) measurements. This compositional change represents the evolution of the film during growth by the three-stage process. Four thin-film CIGS samples with different Cu content were obtained. The Cu/(In+Ga) ratio ranges from 1.24 (Cu-rich)to 0.88 (In-rich), whereas the Ga/(In+Ga) ratio ranges from 0.19 (Cu-rich)to 0.28 (In-rich).The Cu-rich sample exhibits a shallow majority-carrier trap with an activation energy of 0.12 eV and another deeper trap with an activation energy of 0.28 eV, whereas the In-rich sample has a shallow minority-carrier trap with an activation energy of 0.12 eV. The two samples show evidence of a deeper trap at higher temperature. C-V measurements showed that the average carrier concentration (N values) around the junction of the cell changed as the film transitions from Cu-rich to In-rich. DLTS shows that acceptor-like traps are dominant in samples where CIGS grains did not go through the Cu-rich to In(Ga)-rich transition. While donor-like traps are dominant in the In(Ga)-rich samples.

None

The authors present a measurement of R{sub B}, the ratio of the branching fraction for the rare decay D{sup 0} {yields} K{sup +}{pi}{sup -} to that for the Cabibbo-favored decay D{sup 0} {yields} K{sup -}{pi}{sup +}. Charge conjugate decays are implicitly included. A signal of 2005 {+-} 104 events for the decay D{sup 0} {yields} K{sup +}{pi}{sup -} is obtained using the CDF II detector at the Fermilab Tevatron collider. The data set corresponds to an integrated luminosity of 0.35 fb{sup -1} produced in {bar p}p collisions at {radical}s = 1.96 TeV. Assuming no mixing, they find R{sub B} = [4.05 {+-} 0.21(stat) {+-} 0.11(syst)] x 10{sup -3}. This measurement is consistent with the world average, and comparable in accuracy with the best measurements from other experiments.

The authors present the results of a search for standard model Higgs boson production with decay to WW*, identified through the leptonic final states e{sup +}e{sup -} {bar {nu}}{nu}, e{sup {+-}}{mu}{sup {-+}} {bar {nu}}{nu} and {mu}{sup +} {mu}{sup -} {bar {nu}}{nu}. This search uses 360 pb{sup -1} of data collected from p{bar p} collisions at {radical}s = 1.96 TeV by the upgraded Collider Detector at Fermilab (CDF II). They observe no signal excess and set 95% confidence level upper limits on the production cross section times branching ratio for the Higgs boson to WW* or any new scalar particle with similar decay products. These upper limits range from 5.5 to 3.2 pb for Higgs boson masses between 120 and 200 GeV/c{sup 2}.

The authors present results of a search for anomalous production of events containing a charged lepton ({ell}, either e or {mu}) and a photon ({gamma}), both with high transverse momentum, accompanied by additional signatures, X, including missing transverse energy (E{sub T}) and additional leptons and photons. We use the same kinematic selection criteria as in a previous CDF search, but with a substantially larger data set, 305 pb{sup -1}, a p{bar p} collision energy of 1.96 TeV, and the upgraded CDF II detector. We find 42 {ell}{gamma}E{sub T} events versus a standard model expectation of 37.3 {+-} 5.4 events. The level of excess observed in Run I, 16 events with an expectation of 7.6 {+-} 0.7 events (corresponding to a 2.7{sigma} effect), is not supported by the new data. In the signature of {ell}{ell}{gamma} + X we observe 31 events versus an expectation of 23.0 {+-} 2.7 events. In this sample we find no events with an extra photon or E{sub T} and so find no events like the one ee{gamma}{gamma}E{sub T} event observed in Run I.

We describe a measurement of the top quark mass using events with two charged leptons collected by the CDF II detector from p{bar p} collisions with {radical}s = 1.96 TeV at the Fermilab Tevatron. The likelihood in top mass is calculated for each event by convoluting the leading order matrix element describing q{bar q} {yields} t{bar t} {yields} b{ell}{nu}{sub {ell}}{bar b}{ell}{prime} {nu}{sub {ell}}, with detector resolution functions. The presence of background events in the data sample is modeled using similar calculations involving the matrix elements for major background processes. In a data sample with integrated luminosity of 340 pb{sup -1}, we observe 33 candidate events and measure M{sub top} = 165.2 {+-} 6.1(stat.) {+-} 3.4(syst.) GeV/c{sup 2}. This measurement represents the first application of this method to events with two charged leptons and is the most precise single measurement of the top quark mass in this channel.

Homogeneous charge compression ignition (HCCI) is a new combustion technology that may develop as an alternative to diesel engines with high efficiency and low NOx and particulate matter emissions. This paper describes the HCCI research activities being currently pursued at Lawrence Livermore National Laboratory and at the University of California Berkeley. Current activities include analysis as well as experimental work. On analysis, we have developed two powerful tools: a single zone model and a multi-zone model. The single zone model has proven very successful in predicting start of combustion and providing reasonable estimates for peak cylinder pressure, indicated efficiency and NOX emissions. This model is being applied to develop detailed engine performance maps and control strategies, and to analyze the problem of engine startability. The multi-zone model is capable of very accurate predictions of the combustion process, including HC and CO emissions. The multi-zone model has applicability to the optimization of combustion chamber geometry and operating conditions to achieve controlled combustion at high efficiency and low emissions. On experimental work, we have done a thorough evaluation of operating conditions in a 4-cylinder Volkswagen TDI engine. The engine has been operated over a wide range of conditions by adjusting the intake …

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen or ambient-temperature compressed hydrogen. This flexibility results in multiple advantages with respect to compressed hydrogen tanks or low-pressure liquid hydrogen tanks. Our work is directed at verifying that commercially available aluminum-lined, fiber-wrapped pressure vessels can be safely used to store liquid hydrogen. A series of tests have been conducted, and the results indicate that no significant vessel damage has resulted from cryogenic operation. Future activities include a demonstration project in which the insulated pressure vessels will be installed and tested on two vehicles. A draft standard will also be generated for certification of insulated pressure vessels.

We are working on developing an alternative technology for storage of hydrogen or natural gas on light-duty vehicles. This technology has been titled insulated pressure vessels. Insulated pressure vessels are cryogenic-capable pressure vessels that can accept either liquid fuel or ambient-temperature compressed fuel. Insulated pressure vessels offer the advantages of cryogenic liquid fuel tanks (low weight and volume), with reduced disadvantages (fuel flexibility, lower energy requirement for fuel liquefaction and reduced evaporative losses). The work described in this paper is directed at verifying that commercially available pressure vessels can be safely used to store liquid hydrogen or LNG. The use of commercially available pressure vessels significantly reduces the cost and complexity of the insulated pressure vessel development effort. This paper describes a series of tests that have been done with aluminum-lined, fiber-wrapped vessels to evaluate the damage caused by low temperature operation. All analysis and experiments to date indicate that no significant damage has resulted. Future activities include a demonstration project in which the insulated pressure vessels will be installed and tested on two vehicles. A draft standard will also be generated for obtaining insulated pressure vessel certification.

Homogeneous charge compression ignition (HCCI) is a new combustion technology that may develop as an alternative to diesel engines with high efficiency and low NOx and particulate matter emissions. This paper describes the HCCI research activities being currently pursued at Lawrence Livermore National Laboratory and at the University of California Berkeley. Current activities include analysis as well as experimental work. On analysis, we have developed two powerful tools: a single zone model and a multi-zone model. The single zone model has proven very successful in predicting start of combustion and providing reasonable estimates for peak cylinder pressure, indicated efficiency and NOX emissions. This model is being applied to develop detailed engine performance maps and control strategies, and to analyze the problem of engine startability. The multi-zone model is capable of very accurate predictions of the combustion process, including HC and CO emissions. The multi-zone model h as applicability to the optimization of combustion chamber geometry and operating conditions to achieve controlled combustion at high efficiency and low emissions. On experimental work, we have done a thorough evaluation of operating conditions in a 4-cylinder Volkswagen TDI engine. The engine has been operated over a wide range of conditions by adjusting the …

The oxidation behavior of type 316 stainless steel and candidate advanced alloys for the gas-cooled fast reactor (GCFR) is being investigated at General Atomic Company. The test program consists of oxidation tests in prototypic GCFR environments. Two tests have been completed to date and a third test is under way. The first test was performed in an environment containing a hydrogen/water ratio of 10. The oxidation behavior of all the alloys was good to excellent in this environment. Preferential oxidation of chromium was responsible for this behavior. The second test was performed in an environment containing a hydrogen/water ratio of 0.25, where both chromium and iron oxides are thermodynamically stable. Some of the alloys and some of the ribbed type 316 stainless steel test specimens showed unacceptable oxidation resistance in this environment. In the third test, presently under way, two different pretreatment procedures are being used to control the poor oxidation behavior observed in the second test. Early results show some degree of success.

This study examines the temporal variability of ocean heat uptake in observations and in climate models. Previous work suggests that coupled Atmosphere-Ocean General Circulation Models (A-OGCMs) may have underestimated the observed natural variability of ocean heat content, particularly on decadal and longer timescales. To address this issue, we rely on observed estimates of heat content from the 2004 World Ocean Atlas (WOA-2004) compiled by Levitus et al. (2005). Given information about the distribution of observations in WOA-2004, we evaluate the effects of sparse observational coverage and the infilling that Levitus et al. use to produce the spatially-complete temperature fields required to compute heat content variations. We first show that in ocean basins with limited observational coverage, there are important differences between ocean temperature variability estimated from observed and infilled portions of the basin. We then employ data from control simulations performed with eight different A-OGCMs as a test-bed for studying the effects of sparse, space- and time-varying observational coverage. Subsampling model data with actual observational coverage has a large impact on the inferred temperature variability in the top 300 and 3000 meters of the ocean. This arises from changes in both sampling depth and in the geographical areas sampled. Our …

None

None

We determined the cation distribution and ordering of Si, Al and Fe on the tetrahedral sites of a monoclinic low-sanidine from Itrongay, Madagascar, by combined neutron- and X-ray single-crystal diffraction. The cation distribution was determined by means of a simultaneous refinement using neutron- and X-ray data, as well as by combining scattering densities obtained from separate refinements with chemical data from a microprobe experiment. The two methods give the same results and show that Fe is fully ordered on T1, whereas Al shows a high degree of disorder. Based on this and previously published temperature-dependent X-ray data, we conclude that it is preferential ordering of Fe on T1 even at high temperature, rather than a high diffusion kinetics of Fe, which causes this asymmetry in ordering behavior between Al and Fe. The preferential ordering of Fe3+ relative to Al3+ in T1 is consistent with its 25 percent larger ionic radius.

Microfluidic devices with microelectrodes have the potential to enable studies of phenomena at size scales where behavior may be dominated by different mechanisms than at macroscales. Through our work developing microfluidic devices for dielectrophoretic separation and sensing of cells and particles, we have fabricated devices from which general or more specialized research devices may be derived. Fluid channels from 80 {micro}m wide X 20 {micro}m deep to 1 mm wide to 200 {micro}m deep have been fabricated in glass, with lithographically patterned electrodes from 10 to 80 {micro}m wide on one or both sides on the channels and over topographies tens of microns in heights. the devices are designed to easily interface to electronic and fluidic interconnect packages that permit reuse of devices, rather than one-time use, crude glue-based methods. Such devices may be useful for many applications of interest to the electrochemical and biological community.

As part of Argonne National Laboratory`s Fuel Conditioning Facility (FCF), a computer-based Mass-Tracking (MTG) System has been developed. The MTG System collects, stores, retrieves and processes data on all operations which directly affect the flow of process material through FCF and supports such activities as process modeling, compliance with operating limits (e.g., criticality safety), material control and accountability and operational information services. Its architecture is client/server, with input and output connections to operator`s equipment-control stations on the floor of FCF as well as to dumb terminals and terminal emulators. Its heterogeneous database includes a relational-database manager as well as both binary and ASCII data files. The design of the database, and the software that supports it, is based on a model of discrete accountable items distributed in space and time and constitutes a complete historical record of the material processed in FCF. Although still under development, much of the MTG system has been qualified and is in production use.

Erbium hydride thin films are grown onto polished, a-axis {alpha} Al{sub 2}O{sub 3} (sapphire) substrates by reactive ion beam sputtering and analyzed to determine composition, phase and microstructure. Erbium is sputtered while maintaining a H{sub 2} partial pressure of 1.4 x 10{sup {minus}4} Torr. Growth is conducted at several substrate temperatures between 30 and 500 C. Rutherford backscattering spectrometry (RBS) and elastic recoil detection analyses after deposition show that the H/Er areal density ratio is approximately 3:1 for growth temperatures of 30, 150 and 275 C, while for growth above {approximately}430 C, the ratio of hydrogen to metal is closer to 2:1. However, x-ray diffraction shows that all films have a cubic metal sublattice structure corresponding to that of ErH{sub 2}. RBS and Auger electron that sputtered erbium hydride thin films are relatively free of impurities.

A mobile melt-dilute (MMD) module for the treatment of aluminum research reactor spent fuel is being developed. The process utilizes a closed system approach to retain fission products/gases inside a sealed canister after treatment. The MMD process melts and dilutes spent fuel with depleted uranium to obtain a fissile fraction of less than 0.2. The final ingot is solidified inside the sealed canister and can be stored safely either wet or dry until final disposition or reprocessing. The MMD module can be staged at or near the research reactor fuel storage sites to facilitate the melt-dilute treatment of the spent fuel into a stable non-proliferable form.

Numerous searches for new phenomena have been carried out using data from proton-antiproton collisions at Fermilab's Tevatron. Final states with leptons give signatures which are relatively unique and generally have small backgrounds. We present many of the latest results from the CDF and D0 collaborations from 0.4-1.2 fb{sup -1} of data. Topics include supersymmetry, extra gauge bosons, Randall-Sundrum gravitons, excited electrons and neutral, long-lived particles.

This document describes the physics potential of a new fixed-target program based on a {approx} TeV proton source. Two proton sources are potentially available in the future: the existing Tevatron at Fermilab, which can provide 800 GeV protons for fixed-target physics, and a possible upgrade to the SPS at CERN, called SPS+, which would produce 1 TeV protons on target. In this paper we use an example Tevatron fixed-target program to illustrate the high discovery potential possible in the charm and neutrino sectors. We highlight examples which are either unique to the program or difficult to accomplish at other venues.

The US Department of Energy (DOE) National Center of Excellence for Metals Recycle has recently been established. The vision of this new program is to develop a DOE culture that promotes pollution prevention by considering the recycle and reuse of metal as the first and primary disposition option and burial as a last option. The Center of Excellence takes the approach that unrestricted release of metal is the first priority because it is the most cost-effective disposition pathway. Where this is not appropriate, restricted release, beneficial reuse, and stockpile of ingots are considered. Current recycling activities include the sale of 40,000 tons of scrap metal from the East Tennessee Technology Park (formerly K-25 Plant) K-770 scrap yard, K-1064 surplus equipment and machinery, 7,000 PCB-contaminated drums, 12,000 tons of metal from the Y-l2 scrap yard, and 1,000 metal pallets. In addition, the Center of Excellence is developing a toolbox for project teams that will contain a number of specific tools to facilitate metals recycle. This Internet-based toolbox will include primers, computer programs, and case studies designed to help sites to perform life cycle analysis, perform ALARA (As Low As is Reasonably Achievable) analysis for radiation exposures, provide pollution prevention information and …