Lodestar has been an active participant in the low power Collective Thomson Scattering (CTS) diagnostic at TFTR in collaboration with MIT. Extensive studies were conducted regarding the use of gyrotron scattering as a low cost diagnostic for both energetic ions and alpha particles on TFTR. The numerical scattering code has been improved and compared with similar code developed at JET. The authors have participated and assisted in the CTS experiments through onsite visits and have successfully performed most of the data analysis tasks remotely. Through their analysis on the initial data base accumulated, they are able to understand qualitatively the general features of the anomalous large scattered signal, have proposed an explanation for its generation mechanism, and have suggested a potential new use of CTS as an edge diagnostic.

The family of ternary compounds of composition InxGa1-xAs are of considerable interest for thermophotovoltaic energy converters. The recombination lifetimes of the various compositions are critical to the successful application of these materials as efficient converters. Here we will describe experimental results on the composition. In0.53Ga0.47 that is lattice-matched to InP. We will also describe lifetime results on the compositions In0.68Ga0.32As, with bandgap of 0.60 eV to compositions In0.78Ga0.22As with a bandgap of 0.50 eV. Double heterostructure confinement devices have been made over a range of both n- and p-type doping. These results are preliminary, but the goal is to obtain the radiative and Auger recombination coefficients for the alloys in this composition range.

I present some of the current ideas about a Very Large Hadron Collider [1] which could eventually extend the high energy frontier beyond that of the Large Hadron Collider (LHC) or any other machine seriously conceived at this time.

Recent improvements in computer hardware and software for the acquisition, storage and analysis of series of spectra and images allow for a change in strategy for quantitative microanalysis. For example, in the area of X-ray microanalysis, whereas compositional analysis and elemental distributions have been traditionally performed using point microanalysis and simple intensity mapping from a ROI, respectively, the two tasks are now routinely performed simultaneously through X-ray spectrum-imaging, where full spectra are acquired from pixels in a two-dimensional array of points on the specimen. Commercially available software now allows for the acquisition and storage of such spectrum-images, perhaps comprising as much as 100 MBytes of data or more. A variety of post-acquisition processing tools are provided by the developer to allow the extraction of both X-ray intensity maps, with or without rudimentary background subtraction, or full spectra from pixels of interest. In order to maximize the extraction of information from these large data sets, a number of linear and nonlinear methods are currently being explored that identify statistically significant variations among the series of spectra without a priori assumptions about the content of the data set. Among these methods, linear multivariate statistical analysis (MSA) has a number of significant advantages, …

This report describes an innovative technology, laser ablation-inductively couple plasma-mass spectrometry (LA-ICP-MS), operated in a mobile laboratory, to rapidly detect thorium 230 activity levels in soil samples. This technology was demonstrated on-site during November 1993 at the Gunnison, Colorado, UMTRA project site in support of their remediation effort. The LA-ICP-MS sampling and analysis technique was chosen because of the capability for rapid analysis, approximately three samples per hour, with minimal sample preparation.

This paper describes the design and performance of flashlamp-pumped, Nd:glass. Brewster-angle slab amplifiers intended to be deployed in the National Ignition Facility (NIF). To verify performance, we tested a full-size, three-slab-long, NIF prototype amplifier, which we believe to be the largest flashlamp-pumped Nd:glass amplifier ever assembled. Like the NIF amplifier design, this prototype amplifier had eight 40-cm-square apertures combined in a four-aperture-high by two-aperture-wide matrix. Specially-shaped reflectors, anti-reflective coatings on the blastshields, and preionized flashlamps were used to increase storage efficiency. Cooling gas was flowed over the flashlamps to remove waste pump heat and to accelerate thermal wavefront recovery. The prototype gain results are consistent with model predictions and provide high confidence in the final engineering design of the NIF amplifiers. Although the dimensions, internal positions, and shapes of the components in the NIF amplifiers will be slightly different from the prototype, these differences are small and should produce only slight differences in amplifier performance

The Waste Isolation Pilot Plant (WIPP) is an authorized US Department of Energy (DOE) research and development facility constructed near the city of Carlsbad in southeastern New Mexico. The facility is intended to demonstrate the safe disposal of transuranic (TRU) radioactive waste resulting from US defense activities. Under the WIPP Land Withdrawal Act of 1992 (LWA), federal lands surrounding the WIPP facility were withdrawn from all public use and the title of those lands was transferred to the Secretary of Energy. The DOE's TRU waste is stored, and in some cases is still being generated, at 10 large-quantity and 13 small-quantity sites across the US. After applicable certification requirements have been met, the TRU waste at these sites will be sent to the WIPP to initiate the disposal phase of the facility, which according to current planning is projected to last for approximately 35 years.

This document provides the general strategy for developing and testing the performance of candidate high-level waste melter systems and establishing the basis for selecting the preferred melter system for the high-level waste vitrification plant.

this document provides the fiscal year (FY) 1995 recommended high-level waste melter system development and testing (D and T) requirements. The first phase of melter system testing (FY 1995) will focus on the feasibility of high-temperature operation of recommended high-level waste melter systems. These test requirements will be used to establish the basis for defining detailed testing work scope, cost, and schedules. This document includes a brief summary of the recommended technologies and technical issues associated with each technology. In addition, this document presents the key D and T activities and engineering evaluations to be performed for a particular technology or general melter system support feature. The strategy for testing in Phase 1 (FY 1995) is to pursue testing of the recommended high-temperature technologies, namely the high-temperature, ceramic-lined, joule-heated melter, referred to as the HTCM, and the high-frequency, cold-wall, induction-heated melter, referred to as the cold-crucible melter (CCM). This document provides a detailed description of the FY 1995 D and T needs and requirements relative to each of the high-temperature technologies.

Ultrasonic nondestructive evaluation is an extremely powerful tool for characterizing materials and detecting defects. A majority of the ultrasonic nondestructive evaluation is performed with piezoelectric transducers that generate and detect high frequency acoustic energy. The liquid needed to couple the high frequency acoustic energy from the piezoelectric transducers restricts the applicability of ultrasonics. For example, traditional ultrasonics cannot evaluate parts at elevated temperatures or components that would be damaged by contact with a fluid. They are developing a technology that remotely generates and detects the ultrasonic pulses with lasers and consequently there is no requirement for liquids. Thus the research in laser-based ultrasound allows them to solve inspection problems with ultrasonics that could not be done before. This technology has wide application in many Lawrence Livermore National Laboratory programs, especially when remote and/or non-contact sensing is necessary.

None

The information contained within this document describe a set of proposed designs for evaluating the RTAP supervisory control and data acquisition software. The basis of this evaluation is two-fold: (1) to investigate the feasibility of integrating the components of the U-AVLIS supervisory system into RTAP and (2) to investigate the distributed capabilities of the RTAP system. The evaluation process will be performed in an off-line development area (not in B490) and will concentrate its effort on integrating an unclassified subset of the existing U-AVLIS subsets into RTAP. These subsets will include portions of the Heater Control and Dye Combination Wall sub-systems. For the purpose of this evaluation, both of these subsets will constitute an RTAP environment and will operate remotely from one another. Moreover, it is the intention of this evaluating process to investigate the feasibility of preserving the existing SOM screens and to investigate the ability to retain some of the existing real-time trending capabilities which RTAP does not support. This document contains the proposed implementation designs to support each of the sub-systems. They include a conceptual diagram and a description of the identifiable tasks, requirements, and issues regarding their implementation. This information provides a high-level overview and should …

The presently funded three-year research program, supported by the Division of Materials Sciences of the Office of Basic Energy Sciences, was initiated on August 1, 1993; during the period in which the grant will have been active, $249,561 of support have been provided to date with an additional $79,723 to be spent during the third, final year (ending July 30, 1996). The primary purpose of the program is to develop an understanding of heavy-particle radiation effects -- {alpha}-recoil nuclei, fission fragments, ion-irradiations -- on ceramic materials and the thermal annealing mechanisms by which crystallinity might be restored. During the past two years, we have completed major studies on zircon (ZrSiO{sub 4}), olivine (Mg{sub 2}SiO{sub 4} and ten other compositions), spinel (MgAl{sub 2}O{sub 4} and four other compositions), and silica polymorphs (quartz, coesite and stishovite), as well as berlinite (AlPO{sub 4}) which is isomorphous with quartz. In addition, based on the above research, we propose the use of zircon as a host phase for the immobilization of plutonium resulting from weapons dismantlement.

Argonne National Laboratory (ANL-E) has recently completed the decontamination and decommissioning (D and D) of the JANUS Reactor Facility located in Building 202. The 200 KW reactor operated from August 1963 to March 1992. The facility was used to study the effects of both high and low doses of fission neutrons in animals. There were two exposure rooms on opposite sides of the reactor and the reactor was therefore named after the two-faced Roman god. The High Dose Room was capable of specimen exposure at a dose rate of 3,600 rads per hour. During calendar year 1996 a detailed characterization of the facility was performed by ANL-E Health Physics personnel. ANL-E Analytical Services performed the required sample analysis. An Auditable Safety Analysis and an Environmental Assessment were completed. D and D plans, procedures and procurement documents were prepared and approved. A D and D subcontractor was selected and a firm, fixed price contract awarded for the field work and final survey effort. The D and D subcontractor was mobilized to ANL-E in January 1997. Electrical isolation of all reactor equipment and control panels was accomplished and the equipment removed. A total of 207,230 pounds (94,082 Kg) of lead shielding was …

Three-dimensional imaging techniques, numerical methods for simulating flow and transport, and emergent computational architectures are combined to enable fundamental studies of fluid flow at the pore scale. High resolution reconstructions of porous media obtained using laser scanning confocal microscopy reduce sampling artifacts to sub-micron features, and simultaneously capture multiple grain length scales. However, the volumetric image data sets are extremely large, and there are significant computational challenges in utilizing this information effectively. The principal problem lies in the complexity of the geometry and the retention of this structure in numerical analyses. Lattice Boltzmann (LB) methods provide a direct means to simulate transport processes in complex geometric domains due to the unique ability to treat accurately and efficiently the multitude of discrete boundary conditions. LB methods are numerically explicit as formulated, and this characteristic is exploited through a mapping of the numerical domain to distributed computing architectures. These techniques are applied to perform single phase flow simulations in 3D data sets obtained from cores of Berea sandstone using confocal microscopy. Simulations are performed using both a purpose-built distributed processor computer and a massively parallel processer (MPP) platform.

The authors designed and conducted experiments in a heterogeneous sand pack where gravity-destabilized nonwetting phase invasion (CO{sub 2} and TCE) could be recorded using high resolution light transmission methods. The heterogeneity structure was designed to be reminiscent of fluvial channel lag cut-and-fill architecture and contain a series of capillary barriers. As invasion progressed, nonwetting phase structure developed a series of fingers and pools; behind the growing front they found nonwetting phase saturation to pulsate in certain regions when viscous forces were low. Through a scale analysis, they derive a series of length scales that describe finger diameter, pool height and width, and regions where pulsation occurs within a heterogeneous porous medium. In all cases, they find that the intrinsic pore scale nature of the invasion process and resulting structure must be incorporated into the analysis to explain experimental results. The authors propose a simple macro-scale structural growth model that assembles length scales for sub-structures to delineate nonwetting phase migration from a source into a heterogeneous domain. For such a model applied at the field scale for DNAPL migration, they expect capillary and gravity forces within the complex subsurface lithology to play the primary roles with viscous forces forming a perturbation …

A Run II D0 Inter Cryostat Detector tile array will be composed of 16 identical modules. Each module contains 12 optically isolated scintillating tile elements, each with dimension of 0.1 x 0.1 in {eta} and {phi} in the pseudora-pidity region from 1.1 to 1.4. The 12 tiles in a module are formed by routing grooves in a single piece of scintillator - optical isolation is achieved by fill-ing the grooves with a white re ective epoxy. The procedure for filling these isolation grooves is described here.

The purpose of this Cooperative Research and Development Agreement (CRADA) was to assess and develop control practices for nuisance algae growth in power canal that delivers water to hydro-generation facilities. This growth results in expenditures related not only to lost generation but also labor and materials costs associated with implementing remediation procedures. On an industry-wide basis these costs associated with nuisance algal growth are estimated to be several million dollars per year.

The statistical properties of the long-time chaotic two-dimensional (2D) drift motion of a charged particle in an inhomogeneous magnetic field {beta}(x,y) and a time-dependent electrostatic potential {phi}(x,y,t) are studied by numerical symplectic integration. For a conditionally periodic potential with two or more incommensurate frequencies, an ergodic behavior is demonstrated in which the probability density of the particle position is proportional to the magnetic field {beta}. The accuracy of this prediction is found to be independent of the number N{sub {omega}} of the incommensurate frequencies for N{sub {omega}} {ge}2.

During the past several years, significant research efforts have been made to develop process technology for the selective flotation of fossil resin from western coals. As a result of these efforts, several new flotation technologies have been developed. Operation of a proof-of-concept continuous flotation circuit showed the selective flotation process to be sufficiently profitable to justify the development of a fossil resin industry. However, little attention has been given to the refining of the fossil resin flotation concentrate although solvent refining is a critical step for the fossil resin to become a marketable product. In view of this situation, DOE funded this two-year project to evaluate the following aspects of the fossil resin refining technology: 1) Characterization of the fossil resin flotation concentrate and its refined products; 2) Kinetics of fossil resin extraction; 3) Effects of operating variables on solvent extraction; 4) Extraction solvents; 5) Proof-of-concept continuous refining tests; and 6) Technical and economic analysis. The results from this research effort have led to the following conclusions: Hexane- or heptane-refined fossil resin has a light-yellow color, a melting point of 140 - 142{degrees}C, a density of 1.034 gram/cm, and good solubility in nonpolar solvents. Among the four solvents evaluated (hexane, …

The Clebsch-Gordan coefficients of SU(3) are useful in calculations involving baryons and mesons, as well as in calculations involving arbitrary numbers of quarks. For the latter case, one needs the coupling constants between states of nonintegral hypercharges. The existing published tables are insufficient for many such applications, and therefore we have compiled this collection. This report supplies the isoscalar factors required to reconstruct the Clebsch-Gordan coefficients for a large set of products of representations.

The following table is a compilation of chance coincidences between x- ray line wavelengths and crystal planes which will reflect those wavelengths near normal incidence. The motivation is to explore the possibilities for expanding the range of choices for near normal incidence x-ray crystal imaging.

New software has been added to IOC core to maintain time stamps. The new software has the ability to maintain time stamps over all IOCs on a network. The purpose of this paper is to explain how EPICS will synchronize the time stamps. In addition, this paper will explain how to configure and use the new EPICS time stamp support software.

An early prototype of the core software for on-line computing systems for the PHENIX detector at RHIC has been developed using the Shlaer-Mellor OOA/RD method, including the automatic generation of C++ source code using a commercial translation engine and {open_quotes}architecture{close_quotes}.