N/A

This preclosure work plan describes the condition of the dangerous waste treatment storage, and/or disposal (TSD) unit after completion of the B Plant Complex decommissioning Transition Phase preclosure activities. This description includes waste characteristics, waste types, locations, and associated hazards. The goal to be met by the Transition Phase preclosure activities is to place the TSD unit into a safe and environmentally secure condition for the long-term Surveillance and Maintenance (S&M) Phase of the facility decommissioning process. This preclosure work plan has been prepared in accordance with Section 8.0 of the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) (Ecology et al. 1996). The preclosure work plan is one of three critical Transition Phase documents, the other two being: B Plant End Points Document (WHC-SD-WM-TPP-054) and B Plant S&M plan. These documents are prepared by the U.S. Department of Energy, Richland Operations Office (DOE-RL) and its contractors with the involvement of Washington State Department of Ecology (Ecology). The tanks and vessels addressed by this preclosure work plan are limited to those tanks end vessels included on the B Plant Complex Part A, Form 3, Permit Application (DOE/RL-88-21). The criteria for determining which tanks or vessels are in the Part …

Laser safety evaluation and output emission measurements were performed (during October and November 2001) on SNL MILES and Mini MILES laser emitting components. The purpose, to verify that these components, not only meet the Class 1 (eye safe) laser hazard criteria of the CDRH Compliance Guide for Laser Products and 21 CFR 1040 Laser Product Performance Standard; but also meet the more stringent ANSI Std. z136.1-2000 Safe Use of Lasers conditions for Class 1 lasers that govern SNL laser operations. The results of these measurements confirmed that all of the Small Arms Laser Transmitters, as currently set (''as is''), meet the Class 1 criteria. Several of the Mini MILES Small Arms Transmitters did not. These were modified and re-tested and now meet the Class 1 laser hazard criteria. All but one System Controllers (hand held and rifle stock) met class 1 criteria for single trigger pulls and all presented Class 3a laser hazard levels if the trigger is held (continuous emission) for more than 5 seconds on a single point target. All units were Class 3a for ''aided'' viewing. These units were modified and re-tested and now meet the Class 1 hazard criteria for both ''aided'' as well as ''unaided'' …

The Standard Model predictions for W{gamma} and Z{gamma} production are tested using an integrated luminosity of 200 pb{sup -1} of p{bar p} collision data collected at the Collider Detector at Fermilab. The cross sections are measured by selecting leptonic decays of the W and Z bosons, and photons with transverse energy E{sub T} > 7 GeV that are well separated from leptons. The production cross sections and kinematic distributions for the W{gamma} and Z{gamma} data are compared to SM predictions.

Describes results of a sample survey of the quality of B20, a biodiesel blend, collected from U.S. public pumps and fleets as part of a joint effort by NREL, the NBB, and engine manufacturers.

Measured distribution coefficients (K{sub d} values) for environmental contaminants provide input data for performance assessments (PA) that evaluate physical and chemical phenomena for release of radionuclides from wasteforms, degradation of engineered components and subsequent transport of radionuclides through environmental media. Research efforts at SRNL to study the effects of formulation and curing variability on the physiochemical properties of the saltstone wasteform produced at the Saltstone Disposal Facility (SDF) are ongoing and provide information for the PA and Saltstone Operations. Furthermore, the range and distribution of plutonium K{sub d} values in soils is not known. Knowledge of these parameters is needed to provide guidance for stochastic modeling in the PA. Under the current SRS liquid waste processing system, supernate from F & H Tank Farm tanks is processed to remove actinides and fission products, resulting in a low-curie Decontaminated Salt Solution (DSS). At the Saltstone Production Facility (SPF), DSS is mixed with premix, comprised of blast furnace slag (BFS), Class F fly ash (FA), and portland cement (OPC) to form a grout mixture. The fresh grout is subsequently placed in SDF vaults where it cures through hydration reactions to produce saltstone, a hardened monolithic waste form. Variation in saltstone composition and …

The purpose of this task was to perform an Independent Validation Review to evaluate the successful implementation and effectiveness of Safety Basis controls, including new and revised controls, to support the implementation of a new DSA/TSR for B239. This task addresses Milestone 2 of FY10 PEP 7.6.6. As the first IVR ever conducted on a LLNL nuclear facility, it was designated a pilot project. The review follows the outline developed for Milestone 1 of the PEP, which is based on the DOE Draft Guide for Performance of Independent Verification Review of Safety Basis Controls. A formal Safety Basis procedure will be developed later, based on the lessons learned with this pilot project. Note, this review is termed a ''Validation'' in order to be consistent with the PEP definition and address issues historically raised about verification mechanisms at LLNL. Validation is intended to confirm that implementing mechanisms realistically establish the ability of TSR LCO, administrative control or safety management program to accomplish its intended safety function and that the controls are being implemented. This effort should not, however, be confused with a compliance assessment against all relevant DOE requirements and national standards. Nor is it used as a vehicle to question …

MOSAIC is a new wavefront metrology that enables complete wavefront characterization from print or aerial image based measurements. Here we describe MOSAIC and verify its utility with a model-based proof of principle.

This document serves as the final report for LDRD project number 04-LW-031, in which we created subpicosecond length, kilo-amp peak current electron beams with the 100 MeV electron/positron linac, using a novel technique designed to produce ultra-short bunch lengths while maintaining the high brightness produced by the S-band photoinjector. In addition, a diagnostic to measure the temporal distribution of the beam was investigated, as conventional pulse length measurement techniques do not apply to extremely short pulses. The creation and diagnosis of beams with both femtosecond length and high transverse brightness is of major concern to next generation acceleration and radiation production experiments. This work leveraged the previous investment in the PLEIADES facility and it's ability to produce high brightness electron beams. In addition, the ultra-short electron pulses generated by this work have been used in conjunction with the PLEIADES X-ray source to produce sub-picosecond, high-brightness X-ray pulses.

The CORBA-based Simulator was a Laboratory Directed Research and Development (LDRD) project that applied simulation techniques to explore critical questions about distributed control systems. The simulator project used a three-prong approach that studied object-oriented distribution tools, computer network modeling, and simulation of key control system scenarios. The National Ignition Facility's (NIF) optical alignment system was modeled to study control system operations. The alignment of NIF's 192 beamlines is a large complex operation involving more than 100 computer systems and 8000 mechanized devices. The alignment process is defined by a detailed set of procedures; however, many of the steps are deterministic. The alignment steps for a poorly aligned component are similar to that of a nearly aligned component; however, additional operations/iterations are required to complete the process. Thus, the same alignment operations will require variable amounts of time to perform depending on the current alignment condition as well as other factors. Simulation of the alignment process is necessary to understand beamline alignment time requirements and how shared resources such as the Output Sensor and Target Alignment Sensor effect alignment efficiency. The simulation has provided alignment time estimates and other results based on documented alignment procedures and alignment experience gained in the …

In this document, the hazard categorization is determined for activities associated with Project W-272, Special Case Waste (SWC) Storage Modules that will be placed on concrete slabs in the Solid Waste Operations Complex (SWOC) in the 200 West Area of the Hanford site. In this categorization, the activities that take place within the boundaries of the SWOC are addressed; therefore, only the receipt, offloading, handling, and storing of the Special Case Waste at the SWOC are of concern. This revision updates the radioactive material inventory, reverses the assumption that the SCW meets the criteria of Packaging and Transportation of Radioactive Materials (10 CFR 71), Section 71.75, Qualification of Special Form Radioactive Material, and evaluates the project based upon the criteria and guidance provided by US Department of Energy (DOE)-STD-1027-92, Hazard Categorization and Accident Analysis Techniques for Compliance with DOE Order 5480.23, Nuclear Safety Analysis Reports. The Pacific Northwest Laboratory Building 324 B-Cell waste inventory consists of reactor fuel, irradiated fuel, fuel cladding, and vitrified forms of these fuel elements. The waste contains no toxic chemicals or hydrogenous materials. The proposed storage method is placement of the SCW in special waste overpacks (SWOs) that are then placed in a vendor-provided canister …

We discuss possible searches for the new particles predicted by Little Higgs Models at the LHC. By using a simulation of the ATLAS detector, we demonstrate how the predicted quark, gauge bosons and additional Higgs bosons can be found and estimate the mass range over which their properties can be constrained.

A day-long retreat was held January 15, 1999 to chart the future directions for chemical dynamics studies at the Advanced Light Source. This represents an important period for the Chemical Dynamics Beamline, as the hardware is well-developed, most of the initial experimental objectives have been realized and the mission is now to identify the future scientific priorities for the beamline and attract users of the highest caliber. To this end, we have developed a detailed scientific program for the near term; identified and prioritized the long range scientific opportunities, identified essential new hardware, and outlined an aggressive outreach program to involve the chemical physics community.

Understanding how water and solutes move through the vadose zone is necessary to make effective remedial action decisions where contaminants were spilled or leaked at the ground surface or were buried in shallow land-disposal sites. In layered, heterogeneous systems, high contrasts in hydraulic conductivity can lead to formation of perched water zones, and enhanced lateral spread of contamination. Two conceptual models are considered solute for migration through the vadose zone. In the diffuse flow conceptual model, perched water zones accumulate until the head over the perching layer becomes sufficient to drive the infiltration through the perching layer. In the preferential flow conceptual model, perched water moves laterally until a path around the perching layer is encountered. Preferential flow paths can enhance contaminant migration because greater moisture saturation leads to higher advective velocities, and the preferential flow paths bypass low permeability layers with higher sorption capacity. Monitoring wells and instrumented boreholes were installed around a newly constructed industrial-waste percolation pond and an ephemeral river that lie over a 150-m-thick layered vadose zone. Background data gathered before discharge to the pond began show the presence of at least one, and possibly two, deep perched zones. The shallower zone, at approximately 45-m below …

The icosahedral symmetry is one of the most intriguing symmetries, as it not only presents challenge but it appears in many fullerenes and high energetic materials such as the dodecahedral N{sub 20}. We have considered the combinatorics of all irreducible representations of the icosahedral symmetry for a number of multinomial partitions for vertex, face and edge colorings in this work. We have constructed the combinatorial tables for all irreducible representations for various multinomial partitions of colorings for the vertices, edge and faces of the icosahedron. These techniques should have important applications to enumerations and spectroscopy of fullerenes and high-energy materials such as N{sub 20}.

The character table of the fully non-rigid water pentamer, (H{sub 2}O){sub 5} is derived for the first time. The group of all feasible permutations is the wreath product group S{sub 5}[S{sub 2}] and it consists of 3840 operations divided into 36 conjugacy classes and irreducible representations. We have shown that the full character table can be constructed using elegant matrix type generator algebra. The character table has been applied to the water pentamer by obtaining the nuclear spin statistical weights of the rovibronic levels and tunneling splittings of the fully non-rigid pentamer. We have also obtained the statistical weights and tunneling splittings of a semi-rigid deuterated pentamer that exhibits pseudo rotation with an averaged C{sub 5h}(G{sub 10}) symmetry used in the assignment of vibration-rotation-tunneling spectra . The correlation tables have been constructed for the semirigid (G{sub 10}) to non-rigid (G{sub 3840}) groups for the rotational levels and tunneling levels. The nuclear spin statistical weights have also been derived for both the limits.

Laser ablation-inductively coupled plasma-atomic emission spectrometry was used for in situ determination of uranium and thorium concentrations in soil at 80 sampling sites in the Sewage Treatment Plant area. This work was performed by the Environmental Technology Development Program of the Ames Laboratory using a completely self-contained mobile laboratory. This laboratory, the mobile demonstration laboratory for environmental screening technologies and the robotic sampling accessory, were designed and constructed by the Ames Laboratory during FY 1992. The instrumentation is capable of analyzing each sample for twenty operator-defined elements simultaneously. Using the MDLEST/RSA, the uranium concentrations in the soil at the 80 sampling sites were found to range from <20 parts-per-million (ppM)(<13.5 pCi/g) to 303 ppM (205 pCi/g). The 95% confidence interval for these field determined values range from 80 to 110 ppM. Bore hole samples from two sites were analyzed. No measurable uranium concentration was detected below the one foot depth. Seven samples taken from sites within an area currently under remediation were analyzed and found to contain uranium concentrations ranging from 101 ppM (68.3 pCi/g) to 788 ppM (532 pCi/g). Soil samples were taken from twelve of the 80 sampling sites in the field, using conventional sampling techniques. These samples …

Emission factors for black carbon (BC) and particle number (PN) were measured from 226 individual heavy-duty (HD) diesel-fueled trucks driving through a 1 km-long California highway tunnel in August 2006. Emission factors were based on concurrent increases in BC, PN, and CO{sub 2}B concentrations (measured at 1 Hz) that corresponded to the passage of individual HD trucks. The distributions of BC and PN emission factors from individual HD trucks are skewed, meaning that a large fraction of pollution comes from a small fraction of the in-use vehicle fleet. The highest-emitting 10% of trucks were responsible for {approx} 40% of total BC and PN emissions from all HD trucks. BC emissions were log-normally distributed with a mean emission factor of 1.7 g kg {sup -1} and maximum values of {approx} 10 g kg{sup -1}. Corresponding values for PN emission factors were 4.7 x 10{sup 15} and 4 x 10{sup 16} kg{sup -1}. There was minimal overlap among high-emitters of these two pollutants: only 1 of the 226 HD trucks measured was found to be among the highest 10% for both BC and PN. Monte Carlo resampling of the distribution of BC emission factors observed in this study revealed that uncertainties (1{sigma}) …

The process criteria proposed use of the existing organic wash column, 10, as a stripping column for the neptunium accumulation and isolation cycles. It is now proposed to employ a new processing concept which will permit the use of the scrub section of the neptunium extraction column, 1S, for neptunium stripping thereby obviating the use of the 10 Column. This proposed new scheme will provide increased neptunium stripping efficiency and greater processing flexibility for the 1S Column. The revision will require four new jumpers, but will permit the deletion of eight jumpers required for the original proposal. This document discusses the technical bases and incentives for the proposed change and presents revised flow diagrams and jumper routings.

None

An important task for Homeland Security is the prediction of threat vulnerabilities, such as through the detection of relationships between seemingly disjoint entities. A structure used for this task is a ''semantic graph'', also known as a ''relational data graph'' or an ''attributed relational graph''. These graphs encode relationships as typed links between a pair of typed nodes. Indeed, semantic graphs are very similar to semantic networks used in AI. The node and link types are related through an ontology graph (also known as a schema). Furthermore, each node has a set of attributes associated with it (e.g., ''age'' may be an attribute of a node of type ''person''). Unfortunately, the selection of types and attributes for both nodes and links depends on human expertise and is somewhat subjective and even arbitrary. This subjectiveness introduces biases into any algorithm that operates on semantic graphs. Here, we raise some knowledge representation issues for semantic graphs and provide some possible solutions using recently developed ideas in the field of complex networks. In particular, we use the concept of transitivity to evaluate the relevance of individual links in the semantic graph for detecting relationships. We also propose new statistical measures for semantic graphs …

A fast-neutron pinhole camera with high detection efficiency and nanosecond time-resolution has been developed and applied to the investigation of the spatial and temporal distributions of DD- and DT-neutrons produced by thermonuclear plasmas. The pinhole consists of a specially designed 1.15 m long copper collimator with an effective aperture of 1 mm diameter. Several different types of spatial resolution detectors have been used at the image plane: (1) a multi-element, scintillation-photomultiplier system used for time-resolved measurements consisting of sixty-one individual detectors, (2) a scintillation-fiber-chamber coupled to a gated image-intensifier tube used for direct photographing of the neutron image, and (3) a propane bubble chamber used for time-integrated recording with a capability to distinguish DD- from DT-neutrons. Pulsed neutron sources with typical dimensions of 1 cm emitting of the order of 10/sup 12/ neutrons over a time period of 10-100 nsec have been investigated. A spatial resolution of 1 mm and a time resolution of approximately 10 nsec was achieved in the investigations of dense plasma compression phenomena.

The authors have grown epitaxial Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3} (PMN) and (1-x)(Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3})-x(PBTiO{sub 3})(PMN-PT)thin films by metalorganic chemical vapor deposition at 700 -- 780 C on (100) SrTiO{sub 3} and SrRuO{sub 3}/SrTiO{sub 3} substrates. The zero-bias permittivity and loss measured at room temperature and 10 kHz for 220 nm thick pure PMN films were 900 and 1.5%, respectively. For PMN-PT films the small-signal permittivity ranged from 1000 to 1500 depending on deposition conditions and Ti content; correspondingly low values for the zero-bias dielectric loss between 1 and 5% were determined for all specimens. For PMN-PT with x of approximately 0.30--0.35, polarization hysteresis with P{sub r}{approximately}18{mu}C/cm{sup 2} was obtained. Initial piezoresponse data are discussed.

In the design of explosive systems the generic problem that one must consider is the propagation of a well-developed detonation wave sweeping through an explosive charge with a complex shape. At a given instant of time the lead detonation shock is a surface that occupies a region of the explosive and has a dimension that is characteristic of the explosive device, typically on the scale of meters. The detonation shock is powered by a detonation reaction zone, sitting immediately behind the shock, which is on the scale of 1 millimeter or less. Thus, the ratio of the reaction zone thickness to the device dimension is of the order of 1/1,000 or less. This scale disparity can lead to great difficulties in computing three-dimensional detonation dynamics. An attack on the dilemma for the computation of detonation systems has lead to the invention of sub-scale models for a propagating detonation front that they refer to herein as program burn models. The program burn model seeks not to resolve the fine scale of the reaction zone in the sense of a DNS simulation. The goal of a program burn simulation is to resolve the hydrodynamics in the inert product gases on a grid …