The development of large-bore, high-field magnets for fusion energy applications requires a system approach to both magnet and conductor design. At Lawrence Livermore National Laboratory (LLNL), the criteria used to choose superconductors include: strain tolerance, radiation tolerance, heat removal, stability, fabricability, and cost. We report on the performance of industrially produced, prototype, Ti-modified Nb/sub 3/Sn wires developed with LLNL support. Wire performance characteristics evaluated include critical current as a function of magnetic field, temperature, and applied strain. Tests were performed to determine how this performance translates to the performance of a cable-in-conduit conductor system using this wire. An alternative to Nb/sub 3/Sn superconductors is NbN, which is strain and radiation insensitive. We report preliminary efforts to produce multifilamentary NbN conductors by liquid-metal infiltration of NbN-coated, high-strength fibers. In addition, we discuss the fabrication of multifilamentary NbN conductors and their possible impact on magnet design.

The first targets for the 20 TW SHIVA laser system were designed. They are simple glass micro-balloons, approximately 300 ..mu..m in diameter and 2 ..mu..m thick, filled with D-T gas. Using LASNEX, whose model physics was utilized successfully for ARGUS targets, we optimize for both gain and yield. The target behaves as an exploding pusher. Different simple analytic models for the physics of this mode are presented, and are tested by comparing their scaling predictions, at constant absorbed power, with those demonstrated by LASNEX. Emphasis is placed on successful prediction of the basic quantities of peak ion temperature and compression, rather than neutron yield or n tau.

The lowest mesons made up of a light quark and a strange quark produced from a K beam show a good agreement with expectations of the quark model. This good agreement leads to the prediction of the light isoscalar and isovector states and the isoscalar s{bar s} states. Except for one mystery The X(1590) the 2{sup ++} states seems to be well described by the expected ideally mixed q{bar q} states up to 2. 0 GeV. Above 2.0 GeV a new degree of freedom seems to be excited with respect to the breakdown of the OZI rule in production of 2{sup ++} resonances that decay into {phi}{phi}. This is to be contrasted with the situation for the O{sup ++} isoscalar states which seems to show a new degree of freedom for its mesons in its ground state. One might conclude that since the O{sup ++} glueball is predicted by lattice calculations to be degenerate with the s{bar s} O{sup ++} meson, that the very unusual assortment of isoscalar O{sup ++} mesons are due to glueball mixing.

A boundary layer injection method of controlling scale-buildup in geothermal two-phase flow nozzles is studied. The object of this study is to set an upper limit on the ratio of the injected mass flow rate to the free stream mass flow rate that is necessary to isolate the scale carrying free stream flow from the nozzle wall. In order to develop a numerical model of the boundary layer flow, assumptions are made which reduce the results to order of magnitude approximations. Two configurations of nozzles with various injection flow rates are tried. It is found by numerical experiment that a nozzle with injection through a 1 mm thick ring near the inlet, is more efficient at isolating the free stream than a porous nozzle. A mass flow rate ratio of 0.173% was necessary to achieve this effect. It may be concluded that an upper limit on the mass flow rate ratio is about 2.0% with injection through a ring near the inlet, and that boundary layer injection is a reasonable method of controlling scale-buildup. A glossary of variables, program documentation and listings are presented for programs GMD15SR8, TRACK11, and TRACK12.

Sandia National Laboratories has completed a requirements study for a networked mass storage system. The areas of user functionality, network connectivity, and performance were analyzed to determine specifications for a Network Storage Service to operate in supercomputer environment. 4 refs.

This report is a preliminary analysis of the expansion potential of the existing nuclear power sites, in particular their potential for development into nuclear energy centers (NECs) of 10 (GW(e) or greater. The analysis is based primarily on matching the most important physical characteristics of a site against the dominating site criteria. Sites reviewed consist mainly of those in the 1974 through 1976 ERDA Nuclear Power Stations listings without regard to the present status of reactor construction plans. Also a small number of potential NEC sites that are not associated with existing power stations were reviewed. Each site was categorized in terms of its potential as: a dispersed site of 5 GW(e) or less; a mini-NEC of 5 to 10 GW(e); NECs of 10 to 20 GW(e); and large NECs of more than 20 GW(e). The sites were categorized on their ultimate potential without regard to political considerations that might restrain their development. The analysis indicates that nearly 40 percent of existing sites have potential for expansion to nuclear energy centers.

We report the design and status of an FEL experiment at the Brookhaven National Laboratory Accelerator Test Facility. A 50 MeV high brightness electron beam will be utilized for an oscillator experiment in the visible wavelength region. The microwiggler to be used is a superferric planar undulator with a 0.88 cm period, 60 cm length and K = 0.35. The optical cavity is a 368 cm long stable resonator with broadband dielectric coated mirrors. 8 refs., 2 figs., 4 tabs.

This publication presents current data on production, consumption, stocks, imports, exports, and prices of the principal energy commodities in the United States. Also included are data on international production of crude oil, consumption of petroleum products, petroleum stocks, and production of electricity from nuclear-powered facilities. 36 figs., 57 tabs.

Investigations of mass and kinetic-energy distributions from spontaneous fission have been extended in recent years to an isotope of element 104 and, for half-lives, to an isotope of element 108. The results have been surprising in that spontaneous fission half-lives have turned out to be much longer than expected and mass and kinetic- energy distributions were found to abruptly shift away from those of the lighter actinides, showing two modes of fission. These new developments have caused a re-evaluation of our understanding of the fission process, bringing an even deeper appreciation of the role played by nuclear shell effects upon spontaneous fission properties. 16 refs., 10 figs.

We report here the low emittance beam transport line for laser acceleration experiments at the Brookhaven Accelerator Test Facility (ATF). In order to preserve the low emittance ({approximately} 10{sup -10} m-rad) 50 MeV electron beam, great care has to be paid to the higher-order effects. The low-emittance transport line consists of two parts; the first part performs and emittance selection, and the other part provides the possibility of energy selection and beam transport to the experimental area. 7 refs., 5 figs., 7 tabs.

A procedure has been developed for matching prospective users and producers of synthetic fuels. The matching procedure, which involves a hierarchical screening process, is designed to assist OFC in: locating a supplier for a firm that wishes to obtain synthetic fuel exemption (Fuel Use Act); determining whether the fuel supplier proposed by a petitioner is technically and economically capable of meeting the petitioner's needs; and assisting the Synthetic Fuels Corporation in evaluating potential markets for synthetic fuels. Application of the screening procedure resulted in the identification of one or more candidates for supplying synthetic fuel to each of the prospective users. In this report the development of the screening procedure is described. Chapter 1 contains a detailed description of the seven screens; Chapter 2 describes the development of the hierarchical procedure for applying the screens to each synthetic fuels project; Chapter 3 describes the modification of the screening procedure for low and medium Btu gas; Chapter 4 describes the application of the procedure. Appendix A is a list of references used in developing the procedure; Appendix B is a detailed listing of proposed and ongoing synthetic fuel projects.

None

The initial multi-mode interfacial velocity and density perturbations present at the onset of a small Atwood number, incompressible, miscible, Rayleigh-Taylor instability-driven mixing layer have been quantified using a combination of experimental techniques. The streamwise interfacial and spanwise interfacial perturbations were measured using high-resolution thermocouples and planar laser-induced fluorescence (PLIF), respectively. The initial multi-mode streamwise velocity perturbations at the two-fluid density interface were measured using particle-image velocimetry (PIV). It was found that the measured initial conditions describe an initially anisotropic state, in which the perturbations in the streamwise and spanwise directions are independent of one another. The evolution of various fluctuating velocity and density statistics, together with velocity and density variance spectra, were measured using PIV and high-resolution thermocouple data. The evolution of the velocity and density statistics is used to investigate the early-time evolution and the onset of strongly-nonlinear, transitional dynamics within the mixing layer. The early-time evolution of the density and vertical velocity variance spectra indicate that velocity fluctuations are the dominant mechanism driving the instability development. The implications of the present experimental measurements on the initialization of Reynolds-averaged turbulent transport and mixing models and of direct and large-eddy simulations of Rayleigh-Taylor instability-induced turbulence are discussed.

One strategy for helping the solar industry to grow faster is to use very high efficiency cells under concentrating optics. By using lenses or mirrors to concentrate the light, very small solar cells can be used, reducing the amount of semiconductor material and allowing use of higher efficiency cells, which are now >40% efficient.

The Saltstone Facility Documented Safety Analysis (DSA) is under revision to accommodate changes in the Composite Lower Flammability Limit (CLFL) from the introduction of Isopar into Tank 50. Saltstone samples were prepared with an 'MCU' type salt solution spiked with ammonia. The ammonia released from the saltstone was captured and analyzed. The ammonia concentration found in the headspace of samples maintained at 95 C and 1 atm was, to 95% confidence, less than or equal to 3.9 mg/L. Tank 50 is fed by several influent streams. The salt solution from Tank 50 is pumped to the salt feed tank (SFT) in the Saltstone Production Facility (SPF). The premix materials cement, slag and fly ash are blended together prior to transfer to the grout mixer. The premix is fed to the grout mixer in the SPF and the salt solution is incorporated into the premix in the grout mixer, yielding saltstone slurry. The saltstone slurry drops into a hopper and then is pumped to the vault. The Saltstone Facility Documented Safety Analysis (DSA) is under revision to accommodate changes in the Composite Lower Flammability Limit (CLFL) from the introduction of Isopar{reg_sign} L into Tank 50. Waste Solidification-Engineering requested that the Savannah …

This document includes tables of analytical data for Hanford Site environmental surveillance samples collected in 2006.

None

This work is part of a larger project to develop a modeling capability for magnetron sputter deposition. The process is divided into four steps: plasma transport, target sputter, neutral gas and sputtered atom transport, and film growth, shown schematically in Fig. 1. Each of these is simulated separately in this Part 1 of the project, which is jointly funded between CMLS and Engineering. The Engineering portion is the plasma modeling, in step 1. The plasma modeling was performed using the Object-Oriented Particle-In-Cell code (OOPIC) from UC Berkeley [1]. Figure 2 shows the electron density in the simulated region, using magnetic field strength input from experiments by Bohlmark [2], where a scale of 1% is used. Figures 3 and 4 depict the magnetic field components that were generated using two-dimensional linear interpolation of Bohlmark's experimental data. The goal of the overall modeling tool is to understand, and later predict, relationships between parameters of film deposition we can change (such as gas pressure, gun voltage, and target-substrate distance) and key properties of the results (such as film stress, density, and stoichiometry.) The simulation must use existing codes, either open-source or low-cost, not develop new codes. In part 1 (FY07) we identified and …

It is my pleasure to be here to day to participate in this Conference. My thanks to the organizers for preparing such an interesting agenda on a very difficult topic. My effort in preparing my presentation was performed under the auspices of the U.S. Department of Energy by University of California, Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. And as many of you know Lawrence Livermore National Laboratory is now, as of Oct 1st, under contract to the Lawrence Livermore National Security LLC. There has been a long history of how to view verification of arms control agreements. The basis for verification during the days of SALT was that verification would be based on each country's national technical means. For treaties dealing with strategic missiles this worked well as the individual items subject to verification were of such a size that they were visible by the National Technical Means available at the time. And it was felt that the counting of missiles and launchers could be verified by our National Technical Means. For nuclear testing treaties the use of seismic measurements developed into a capability that was reasonably robust for all but the smallest of nuclear tests. However, once we …

Recent NSTX high power divertor experiments have shown significant and recurring benefits of solid lithium coatings on PFC's to the performance of divertor plasmas in both L- and H- mode confinement regimes heated by high-power neutral beams. The next step in this work is installation of a liquid lithium divertor (LLD) to achieve density control for inductionless current drive capability (e.g., about a 15-25% ne decrease from present highest non-inductionless fraction discharges which often evolve toward the density limit, ne/nGW~1), to enable ne scan capability (x2) in the H-mode, to test the ability to operate at significantly lower density for future ST-CTF reactor designs (e.g., ne/nGW = 0.25), and eventually to investigate high heat-flux power handling (10 MW/m2) with longpulse discharges (>1.5s). The first step (LLD-1) physics design encompasses the desired plasma requirements, the experimental capabilities and conditions, power handling, radial location, pumping capability, operating temperature, lithium filling, MHD forces, and diagnostics for control and characterization.

The authors discuss a cosmology in which cold dark-matter particles decay into relativistic particles. They argue that such decays could lead naturally to a bulk viscosity in the cosmic fluid. for decay lifetimes comparable to the present hubble age, this bulk viscosity enters the cosmic energy equation as an effective negative pressure. They investigate whether this negative pressure is of sufficient magnitude to account for the observed cosmic acceleration. They show that a single decaying species in a {Lambda} = 0, flat, dark-matter dominated cosmology can not reproduce the observed magnitude-redshift relation from Type Ia supernovae. However, a delayed bulk viscosity, possibly due to a cascade of decaying particles may be able to account for a significant fraction of the apparent cosmic acceleration. Possible candidate nonrelativistic particles for this scenario include sterile neutrinos or gauge-mediated decaying supersymmetric particles.

This report covers the following titles: (1) Synthesis of compounds from {sup 14}CO{sub 2} by Chlorella in the dark following preillumination; (2) The effect of oxygen on formation of glycolic acid and other products during photosynthesis by Chlorella; (3) Phosphatase action on phosphoglycolic, 3-phosphoglyceric, and phosphoenolpyruvic acids in spinach chloroplast fragments in the presence and absence of high concentrations of methanol; (4) Absorption spectra of scattering samples. I. An evaluation of three different spectrophotometric techniques using Chlorella; (5) Absorption spectra of scattering samples. II. Scattered transmission spectra of leaves, chloroplasts, and quantasomes of spinach; (6) The effect of sonication of spinach chloroplasts on photosynthetic phosphorylation; (7) Concerning the occurrence of {alpha},{alpha}-tocopherol and {alpha}-tocopherylquinone in chloroplasts and quantasomes; (8) Effects of ultraviolet and gamma radiation of thymine in frozen aqueous solution and in the solid state; and (9) A rapid method for the identification of small quantities of lipid-soluble vitamins and quinones in biological material.

The purpose of the Waste Isolation Pilot Plant Annual Site Environmental Report for 2006 (ASER) is to provide information required by U.S. Department of Energy (DOE) Order 231.1A, Environment, Safety, and Health Reporting. Specifically, the ASER presents summary environmental data that: (a) Characterize site environmental management performance; (b) Summarize environmental occurrences and responses reported during the calendar year; (c) Confirm compliance with environmental standards and requirements; and (d) Highlight significant facility programs and efforts. The DOE Carlsbad Field Office (CBFO) and Washington TRU Solutions LLC (WTS) maintain and preserve the environmental resources at the WIPP site. DOE Order 231.1A; DOE Order 450.1, Environmental Protection Program; and DOE Order 5400.5, Radiation Protection of the Public and Environment, require that the affected environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This report was prepared in accordance with DOE Order 231.1A. This order requires that DOE facilities submit an ASER to the DOE Headquarters Office of the Assistant Secretary for Environment, Safety, and Health. The WIPP Hazardous Waste Facility Permit (HWFP) (No. NM4890139088-TSDF [treatment, storage, and disposal facility]) further requires that the ASER be provided to the New Mexico Environment Department …

Based on the measured four-dimensional rate for D{sub s}{sup +} {yields} {phi}e{sup +}{nu}{sub e} decays, they have determined the ratios of the three hadronic form factors, {tau}{sub V} = V(0)/A{sub 1}(0) = 1.636 {+-} 0.067 {+-} 0.038 and {tau}{sub 2} = A{sub 2}(0)/A{sub 1}(0) = 0.705 {+-} 0.056 {+-} 0.029, using a simple pole ansatz for the q{sup 2} dependence, with fixed values of the pole masses for both the vector and axial form factors. By a separate fit to the same data, they have also extracted the pole mass for the axial form factors, m{sub A}: {tau}{sub V} = V(0)/A{sub 1}(0) = 1.633 {+-} 0.081 {+-} 0.068, {tau}{sub 2} = A{sub 2}(0)/A{sub 1}(0) = 0.711 {+-} 0.111 {+-} 0.096 and m{sub A} = (2.53{sub -0.35}{sup +0.54} {+-} 0.54)GeV/c{sup 2}.