We have been using the 3d PIC code WARP6 to model the behavior of beams in a heavy ion induction accelerator; such linacs are candidates for an ICF driver. Improvements have been added to the code to model an axially confined beam using comoving axial electric fields to simulate the confining ears'' applied to the accelerating pulses in a real system. We have also added a facility for modeling a beam in a round pipe, applying a capacity matrix to each axial Fourier mode in turn. These additions are described along with results, such as the effect of pipe shape on the beam quality degradation from quadrupole misalignments. 5 refs., 6 figs., 1 tab.

Project W-113 will provide the equipment and facilities necessary to retrieve suspect transuranic (TRU) waste from Trench 04 of the 218W-4C burial ground. As part of the retrieval process, waste drums will be assayed, overpacked, vented, head-gas sampled, and x-rayed prior to shipment to the Phase V storage facility in preparation for receipt at the Waste Receiving and Processing Facility (WRAP). Advanced Conceptual Design (ACD) studies focused on project items warranting further definition prior to Title I design and areas where the potential for cost savings existed. This ACD Report documents the studies performed during FY93 to optimize the equipment and facilities provided in relation to other SWOC facilities and to provide additional design information for Definitive Design.

The argon storage dewar at the D0 Assembly Hall was filled with approximately 3100 gallons of high purity liquid argon for the first time on December 3,1990. The oxygen analyzer and high voltage test cell both indicated an oxygen impurity level between 0.4 and 0.5 ppm which is acceptable. The condenser and insulated piping sizing appears to be correct for a fill rate of a couple of hours. Insulation is required around the inlet to this piping in order to reduce the amount of filling time significantly. The graph of the level indication vs. volume of the dewar should be changed to reflect the apparent 5.2-5.4 in. offset. Another data point may be required to narrow this number down further. A majority of the time spent to fill the vessel was associated with the testing of the liquid-this time will shorten as we gain experience. Subsequent deliveries should be ordered to initiate as early in the morning as possible, this appears to be nearly an all day effort. The argon checked prior to delivery by us indicated that it was acceptable. The analysis of the argon purity that Linde provides us is merely a check that the liquid meets our …

Laboratory data for Sixth Round Groundwater samples collected during the 300-FF-5 Operable Unit Remedial Investigation have been reviewed and validated to ensure that they are of sufficient quality to support decisions regarding further actions to be taken at the 300-FF-5 Operable Unit. Table 1-1 is a summary of the validated samples. This report summarizes the results previously presented to Westinghouse Hanford in a series of Preliminary Quality Assurance Reports (PQAR) for the 300-FF-5 Sixth Round Groundwater samples. In some instances, the data qualifiers originally presented in the PQARs have been changed based upon further review of the data; these changes are highlighted in the text.

Westinghouse Hanford Company (WHC) is conducting a two-phased demonstration testing and evaluation of candidate melter system technologies for vitrification of Hanford Site low-level tank wastes. The testing is to be performed by melter equipment and vitrification technology commercial suppliers. This Statement of Work is for Phases 1 and 2 of the demonstration testing program. The primary objective of the demonstration testing is to identify the best available melter system technology for the Hanford Site LLW vitrification facility. Data obtained also will support various WHC engineering studies and conceptual design of the LLW vitrification facility. Multiple technologies will be selected for demonstration and evaluation. Testing will be conducted using non-radioactive LLW simulants in Seller-specified pilot/testing facilities.

The goal of the continuous air monitor (CAM) system at the Los Alamos National Laboratory`s Plutonium Facility (PF-4) is to have a flow rate of 1 cubic feet per minute (cfm) drawn through the CAMs. However, design limitations in the house vacuum result in many CAMs having less than 1 cfm being drawn through them. Reduced flow rates through CAMs present a compromise in worker protection. Laboratory Health and Safety personnel and DOE officials established a flow rate of 0.5 cfm or less as operationally unacceptable. This report quantitatively estimated the difference in risk to workers from a reduced flow rate of 0.5 cfm relative to the risk inherent with a flow rate of 1 cfm. I calculated risk in terms of Committed Effective Dose Equivalent (CEDE) and used units of rem. Estimates for the increase in risk for 0.5 cfm compared to 1 cfm ranged from 0.32 rem to 3.3 rem. The difference in the minimum alarm concentration between 0.5 cfm and I cfm was also compared and was estimated to range from 0.4 rem to 4 rem.

DOE has prepared an Environmental Assessment (EA) (DOE/EA-0921) evaluating the proposed construction and operation of the Ambulatory Research and Education Center (AREC), which would be located on the top seven floors of the existing NeuroSensory Research Center (NRC) on the campus of the Oregon Health Sciences University (OHSU) at Portland, Oregon. The proposed action would combine activities scattered across the campus into a central facility. Based on the analysis in the EA, DOE has determined that the proposed action does not constitute a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969, 42 USC 4321 et seq. Therefore, an environmental impact statement (EIS) is not required and the Department is issuing this Finding of No Significant Impact (FONSI).

We study the structure of the moduli spaces of vacua and superpotentials of N = 2 supersymmetric gauge theories in three dimensions. By analyzing the instanton corrections, we compute the exact superpotentials and determine the quantum Coulomb and Higgs branches of the theories in the weak coupling regions. We find candidates for non-trivial N = 2 superconformal field theories at the singularities of the moduli spaces. The analysis is carried out explicitly for gauge groups U(N{sub c}) and SU(N{sub c}) with N{sub f} flavors. We show that the field theory results are in complete agreement with the intersecting branes picture. We also compute the exact superpotentials for arbitrary gauge groups and arbitrary matter content.

The Aegis system at Lawrence Livermore National Laboratory (LLNL) is being developed to provide a real-time emergency response management capability for a diverse range of environmental monitoring applications. The Aegis system is designed to integrate a variety of environmental, emergency, and process monitoring sensor systems using a flexible, modular architecture that can be readily configured for any number of industrial, commercial, or government sites. Several unique LLNL technologies are being integrated via this effort that will provide tracking of environmental contaminants, real-time identification of potentially unacceptable conditions, and facilitation of emergency or measured response management operations. Potential areas of application include: monitoring-surface/ground water, air, radiation; waste effluent & storm/drain line; water quality (water storage, treatment, and distribution); fixed processes, safety systems; critical facilities; hazardous spill management; rapid environmental monitoring deployment; watershed protection; ecosystem management and restoration; enforcement and compliance.

We could become convinced that a particular theory of very-high-energy physics is correct if (1) it has a tightly constrained structure and is linked strongly enough with observed particle interactions, or (2) it predicts new physics beyond the standard model which is discovered. The author makes the case that experiments of this decade and the next allow the possibility that we might become convinced that grand unification, a candidate theory of the second type, is correct.

The STAR experiment at RHIC is a TPC-based, general purpose detector designed to obtain charged particle spectra, with an emphasis on hadrons over a large phase space. An electromagnetic calorimeter provides measurement of e's, {gamma}'s, {pi}{sup 0}'s and jets. Data-taking with Au + Au collisions at {radical}5 = 200 GeV/c{sup 2} begins in Fall 1999. The STAR experiment's investigation of techniques and signals using hard probes to study the high energy-density matter at RHIC and to search for quark-gluon plasma formation will be described.

New short-pulse laser technology has made possible the production of extremely bright laser sources. The use of these new techniques on large scale Nd:Glass based laser systems would make it possible to produce 1000 TW (Petawatt) pulses. Such pulses would yield focused intensities exceeding 10{sup 21}W/cm{sup 2} corresponding to an electric field in excess of 100 e/a{sub 0}{sup 2} and an energy density equivalent to that of a 10 keV blackbody. Such a source would have important applications in x-ray laser research and lead to a fundamentally new class of experiments in atomic, nuclear, solid state, plasma and high-energy density physics. Such a facility could be constructed with existing chirped-pulse'' technology. A one-year period of research addressing outstanding technical questions can extend the technology resulting in a more compact and cost effective design. For this reason, we are seeking a Director's Initiative grant in the amount of $590,000 for FY89 to investigate these issues. An equivalent amount in personnel and facilities would be provided by Y-Division. The study will include development of a chirped-pulse'' front-end capable of producing laser pulses of 2 J at 1.053 {mu}m with a 1 psec pulsewidth laser. Upon completion, this front-end will be installed on …

In this paper the authors compare and contrast three powerful methods for experimentally measuring bond energies in polyatomic molecules. The methods are: radical kinetics; gas phase acidity cycles; and photoionization mass spectroscopy. The knowledge of the values of bond energies are a basic piece of information to a chemist. Chemical reactions involve the making and breaking of chemical bonds. It has been shown that comparable bonds in polyatomic molecules, compared to the same bonds in radicals, can be significantly different. These bond energies can be measured in terms of bond dissociation energies.

None

There is growing evidence that global warming could become a major global environmental threat during the 21st century. The precautionary principle commands preventive action, at both national and international levels, to minimize this potential threat. Many near-term, relatively inexpensive, mitigation options are available. In addition, long-term research is required to evaluate and develop advanced, possibly more expensive, countermeasures, in the eventuality that they may be required. The utilization of power plant CO{sub 2} and its recycling into fossil fuel substitutes by microalgae cultures could be one such long-term technology. Microalgae production is an expanding industry in the U.S., with three commercial systems (of approximately 10 hectare each) producing nutriceuticals, specifically beta-carotene, extracted from Dunaliella, and Spirulina biomass. Microalgae are also used in wastewater treatment. Currently production costs are high, about $10,000/ton of algal biomass, almost two orders of magnitude higher than acceptable for greenhouse gas mitigation. This report reviews the current state-of-the-art, including algal cultivation and harvesting-processing, and outlines a technique for achieving very high productivities. Costs of CO{sub 2} mitigation with microalgae production of oils ({open_quotes}biodiesel{close_quotes}) are estimated and future R&D needs outlined.

In 1992, our group began exploring the requirements for a comprehensive simulation code for toroidal magnetic fusion experiments. There were several motivations for taking this step. First, the new machines being designed were much larger and more expensive than current experiments. Second, these new designs called for much more sophisticated control of the plasma shape and position, as well as the distributions of energy, mass, and current within the plasma. These factors alone made it clear that a comprehensive simulation capability would be an extremely valuable tool for machine design. The final motivating factor was that the national Numerical Tokamak Project (NTP) had recently received High Performance Computing and Communications (HPCC) Grand Challenge funding to model turbulent transport in tokamaks, raising the possibility that first-principles simulations of this process might be practical in the near future. We felt that the best way to capitalize on this development was to integrate the resulting turbulence simulation codes into a comprehensive simulation. Such simulations must include the effects of many microscopic length- and time-scales. In order to do a comprehensive simulation efficiently, the length- and time- scale disparities must be exploited. We proposed to do this by coupling the average or quasistatic effects …

The Westinghouse Savannah River Technology Center was requested by it`s sister site, West Valley Nuclear Service (WVNS), to develop a remote inspection system to gather wall thickness readings of their High Level Waste Tanks. WVNS management chose to take a proactive approach to gain current information on two tanks t hat had been in service since the early 70`s. The tanks contain high level waste, are buried underground, and have only two access ports to an annular space between the tank and the secondary concrete vault. A specialized remote system was proposed to provide both a visual surveillance and ultrasonic thickness measurements of the tank walls. A magnetic wheeled crawler was the basis for the remote delivery system integrated with an off-the-shelf Ultrasonic Data Acquisition System. A development program was initiated for Savannah River Technology Center (SRTC) to design, fabricate, and test a remote system based on the Crawler. The system was completed and involved three crawlers to perform the needed tasks, an Ultrasonic Crawler, a Camera Crawler, and a Surface Prep Crawler. The crawlers were computer controlled so that their operation could be done remotely and their position on the wall could be tracked. The Ultrasonic Crawler controls were …

The authors have rapid-solidification-processed many stainless steels by gas atomization and achieved strength improvements of over 50% relative to conventionally-processed stainless steels with concomitant improvement in corrosion and oxidation behavior. These strength improvements are most pronounced after aging treatments when elevated concentrations of oxygen and vanadium are present in the stainless steel. An austenitic (FCC) stainless steel was prepared by gas atomization and consolidated by hot extrusion at 900 C. These specimens were heat treated for 1 hour at 1,000 C and aged at 600 C for 500 hours. The microstructure of each alloy composition was observed in TEM with bright field imaging. After aging, most alloys showed the same precipitate morphology as before aging. An obvious change, however, was found only in the alloy with highest oxygen content. A high number density of 15 to 20 nm diameter precipitates was measured in this alloy. Moreover, with weak-beam dark field imaging, a very high number density of coherent, 6 to 10 nm diameter precipitates is observed throughout the matrix by Moire fringe contrast. An atom probe field ion microscopy (APFIM) investigation showed that FIM provides high contrast imaging the precipitates. In order to get a more global view of the …

Ten grab samples (2AN-95-1, 2, 3, 4A, 5A; 102-AN-1, 2, 3(A), 3(B), and 4) and one field blank (2AN-95-6) were taken from tank 241-AN-102. In support of the safety screening program, total organic carbon and cyanide were performed as secondary analyses because the differential scanning calorimetry results exceeded the notification limit. These were compared to safety screening limits at a confidence level of 95%. Waste compatibility analyses were performed on the 3 supernate samples and the field blank from the latest sampling event. Results presented in the 45 day and in this report show that the waste in Tank 241-AN-1D2 has energetics greater than 480 J/g (dry) and total organic carbon > 3 wt%; however, with a moisture content > 17 wt%, the tank may be considered ``conditionally`` safe in accordance with the Data Quality Objective to Support Resolution of the Organic Complexant Safety Issue.

The purpose of this guide is to describe each of the documents and record series pertaining to the production, release, and disposal of radioactive barium-lanthanum (RaLa), iodine-131, and cesium-137 at the Department of Energy`s (DOE) Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee. History Associates Incorporated (HAI) prepared this guide as part of DOE`s Epidemiologic Records Inventory Project, which seeks to verify and conduct inventories of epidemiologic and health-related records at various DOE and DOE contractor sites. This introduction briefly describes the Epidemiologic Records Inventory Project and HAI`s role. It provides information on the history of the DOE-Oak Ridge Reservation (ORR), particularly ORNL. Specific attention is given to the production of RaLa and the fission products iodine-131 and cesium-137. This introduction also describes the methodologies HAI used in the selection and inventorying of documents and record series pertaining to RaLa, iodine-131, and cesium-137, and in the production of this guide. Concluding paragraphs describe the arrangement of the record series, explain the information contained in the record series descriptions, and indicate restrictions on access to the records.

This document provides the information to explain to the customer the ETP for the N2 vs H20 as Purge/Hydrostatic Head. This ETP follows the format described in Issurance of New Characterization Equipment Engineering Desk Instructions, 75200-95-013.

Future applications of simulators in process control will see activities with high return on investment in areas such as concurrent engineering, hardware-in-the-loop controller testing, process fault detection, and Internet-retrievable simulation models and tools. These applications are based on advancing technology in the field of simulation technology. In this paper, the advancing technology will be reviewed, and projections to future uses of simulators in process control will be made.

This project was supported through ERDA to demonstrate that the temporal distribution of tritium can be documented by the analysis of bound hydrogen in annual tree-ring samples. The project focuses on two sample locations at the Savannah River Site (SRS), a nuclear material production facility located in Aiken, SC. The SRS provided samples of cross-sections from a single tree that were to be pooled together for analysis. Annual tree-rings were identified in each cross-section sample and separated for the period 1954 to 1993. These annual samples were ground and chemically treated to separate the hollocellulose fraction of the wood, then subsequently combusted and the resulting water counting using low-level liquid scintillation counting equipment. Additionally, the ground annual tree-rings were gamma-counted to determine any temporal variation in radionuclide activity and analyzed with x-ray fluorescence to find any temporal variation in trace-element concentrations. This report presents the results and is intended to be a compilation of the work.

None