During the last quarter, work has focused on developing a numerical model to. approximate the flow characteristics of the Gladys McCall reservoir. Various reservoir models have been used in the study to simulate the well transient pressure and pressure derivative behavior during the reservoir production period. The pressure behavior of the 1983 Reservoir Limits Test (RLT) was closely matched by an elongated linear reservoir model with the well located off-center. The matching procedure appears to provide reasonable estimates of the probable configuration of Gladys McCall reservoir.geometry. Double-slope pressure behavior (on a semilog plot) develops after the. early radial flow period, indicating the existence of a no-flow boundary near the well. At later times, linear flow character (square-root-time straight line) becomes clear when two closer boundaries are both felt at the well.

Diffusion-bonded NiAl-Al[sub 2]O[sub 3] and Ni[sub 3]Al-Al[sub 2]O[sub 3] couples were thermally fatigued at 900 C for 1500 and 3500 cycles. The fiber-matrix interface weakened after 3500 cycles for the Saphikon fibers, while the Altex, PRD-166, and FP fibers showed little, if any, degradation. Diffusion bonding of fibers to Nb matrix is being studied. Coating the fibers slightly increases the tensile strength and has a rule-of-mixtures effect on elastic modulus. Push-out tests on Sumitomo and FP fibers in Ni aluminide matrices were repeated. Al[sub 2]O[sub 3] was evaporated directly from pure oxide rod onto acoustically levitated Si carbide particles, using a down-firing, rod-fed electron beam hearth; superior coatings were subsequently produced using concurrent irradiation with 200-eV argon ion-assist beam. The assist beam produced adherent films with reduced tensile stresses. In diffusion bonding in B-doped Ni[sub 3]Al matrices subjected to compressive bonding at 40 MPa at 1100 C for 1 hr, the diffusion barriers failed to prevent catastrophic particle- matrix reaction, probably because of inadequate film quality. AlN coatings are currently being experimented with, produced by both reactive evaporation and by N[sup +]-ion enhanced deposition. A 3-kW rod-fed electron-beam-heated evaporation source has been brought into operation.

We report improvement of the polarization diagnostics and their use in the development of the Optically Pumped Polarized Ion Source (OPPIS).

Experiments have been developed for measuring the rates of chemical reactions liquids and in supercritical Co[sub 2]. A pulsed (Q-switch) Nd:YAG laser at 355 nm was the pump beam for laser flash photolysis studies of molybdenum and tungsten hexacarbonyls undergoing ligand displacement reactions by bidentate chelating agents such as 2,2[prime]-bipyridine in toluene. Experiments were carried out at 0.1 to 150 MPa. In the case of molybdenum complexes, the reaction mechanism for thermal ring closure is found from activation volumes to change from associative interchange to dissociative interchange as substituents on the 2,2[prime]-bipyridine ligands become bulkier. In a similar study of more rigid, substituted phenanthroline bidentate ligands it was found that substituent bulkiness had little effect on the thermal ring closure mechanism. Similar high pressure flash photolysis experiments with tungsten hexacarbonyl have also been completed. The concentration dependence of the fluorescence and nonradiative decay quantum yields for cresyl violet in several solvent have been reported as well as stability constants for the complexation of lithium ion by four different crown ethers dissolved in a room temperature molten salt.

Coupon immersion tests were performed on ASTM A537 Class 1 carbon steel in simulated DWPF recycle solutions at 90 [+-] 2[degrees]C, as part of the continuing effort to investigate the formation of shock-sensitive deposits. Coupons were partially immersed for four months in solutions of the same composition used previously at SRTC and at the DuPont Engineering Test Center (a salt solution containing 0.5 M hydroxide and 0.043 M nitrite). Shock-sensitive deposits were not seen on the coupons from this test. There was considerable general corrosion above the water line due to condensate and distilled water contact of the steel. New immersion tests are being planned for completion by September, 1993. The new test solution will reflect the recycle stream chemistry changes brought about by planned ammonia scrubbing in the DWPF.

An ion exchange unit has been manufactured for WSRC by British Nuclear Fuels, Ltd. This unit consists of three columns, ancillary valving, pumps, lines, and computer controls. It has been delivered to TNX for use in testing a cesium-specific ion exchange resin, developed at WSRC as a potential second generation process for the decontamination of Defense Waste Processing Facility (DWPF) supernate. This resin also has Department of Energy applications at both Oak Ridge and Hanford. Oak Ridge is interested in decontaminating the Melton Valley storage tank supernate, while Hanford is interested in decontaminating the 101-AW and 101-SY supernate streams. Another potential developmental interest is the Savannah River Site (SRS) DWPF recycle stream. The three primary waste streams of interest are the Oak Ridge, Hanford, and SRS, SWPF supernate streams. For these three waste streams, the cesium decontamination factor (DF) will be measured for a non-radioactive, simulated, high-level waste solution. The test objectives, process outlines, and broad characterization of the waste streams are described.

To identify, document, and maintain the Uranium Mill Tailings Remedial Action (UMTRA) Project`s environment, safety, and health (ES&H) regulatory requirements, the US Department of Energy (DOE) UMTRA Project Office tasked the Technical Assistance Contractor (TAC) to develop a regulatory operating envelope for the UMTRA Project. The system selected for managing the UMTRA regulatory operating envelope data bass is based on the Integrated Project Control/Regulatory Compliance System (IPC/RCS) developed by WASTREN, Inc. (WASTREN, 1993). The IPC/RCS is a tool used for identifying regulatory and institutional requirements and indexing them to hardware, personnel, and program systems on a project. The IPC/RCS will be customized for the UMTRA Project surface remedial action and groundwater restoration programs. The purpose of this plan is to establish the process for implementing and maintaining the UMTRA Project`s regulatory operating envelope, which involves identifying all applicable regulatory and institutional requirements and determining compliance status. The plan describes how the Project will identify ES&H regulatory requirements, analyze applicability to the UMTRA Project, and evaluate UMTRA Project compliance status.

An investigation into the preparation of sol-gel coatings for high power lasers was started at LLNL in 1983 and AR coatings were successfully developed for use in the Nova laser in 1984. Several other large lasers now use these coatings. Subsequent work on HR coatings resulted in AlOOH/SiO{sub 2} and later ZrO{sub 2} or HfO{sub 2}/SiO{sub 2} systems of good optical performance. The use of organic polymer binders gave increased damage threshold and enhanced optical performance. We are in the process of scaling up HR fabrication for substrates approximately 38 cm square. Concurrently we are developing sol-gel random phase plates for laser beam smoothing. These have a patterned surface design of silica which induces phase shifts in the beam by variation in the optical path length. Plates of this type on 80 cm diameter substrates have been used successfully on the Nova.

A statistical design and analysis of both elemental analyses and weight percent solids analyses data was utilized to evaluate the MFT homogeneity at low heel levels and low agitator speed at both high and low solids feed concentrations. The homogeneity was also evaluated at both low and high agitator speed at the 6000+ gallons static level. The dynamic level portion of the test simulated feeding the Melter from the MFT to evaluate the uniformity of the solids slurry composition (Frit-PHA-Sludge) entering the melter from the MFT. This final report provides the results and conclusions from the second half of the study, the low weight percent solids concentration portion, as well as a comparison with the results from the first half of the study, the high weight percent solids portion.

The overall objective of the project is to develop and optimize a two-stage fermentation process for the conversion of coal derived synthesis gas in an mixture of alcohols. The goals include the development of superior strains with high product tolerance and productivity, optimization of process conditions for high volumetric productivity and product concentrations, integration and optimization of two stage syngas fermentation, evaluation of bioreactor configurations for enhanced mass transfer, evaluation of syngas conversion by a culture of Butyribacterium methyltrophicum and Clostridium acetobutylicum, development of a membrane based pervaporation system for in situ removal of alcohols, and development of a process for reduction of carbon and electron loss. The specific goals for year one (September 1992 - September 1993) were (1) development of a project work plan, (2) development of superior CO-utilizing strains, (3) optimization of process conditions for conversion of synthesis gas to a mixture of acids in a continuously stirred reactor (CSTR), (4) evaluation of different bioreactor configurations for maximization of mass transfer of synthesis gas, (5) development of a membrane based pervaporation system, and (6) reduction of carbon and electron loss via H{sub 2}CO{sub 2} fermentation. Experimentation and progress toward these goals are described in this report.

The empirical domain of validity of statistical theory is examined as applied to fission data on pre-fission data on pre-fission neutron, charged particle, and {gamma}-ray multiplicities. Systematics are found of the threshold excitation energy for the appearance of nonstatistical fission. From the data on systems with not too high fissility, the relevant phenomenological parameter is the ratio of the threshold temperature T{sub thresh} to the (temperature-dependent) fission barrier height E{sub Bar}(T). The statistical model reproduces the data for T{sub thresh}/E{sub Bar}(T) < 0.26 {plus_minus} 0.05, but underpredicts the multiplicities at higher T{sub thresh}/E{sub Bar}(T) independent of mass and fissility of the systems.

The objectives of this project are to continue reservoir characterization of the Cypress Sandstone; to identify and map facies-defined waterflood units (FDWS); and to design and implement water-alternating-gas (WAG) oil recovery utilizing carbon dioxide (CO{sub 2}) The producibility problems are permeability variation and poor sweep efficiency. Part 1 of the project focuses on the development of computer-generated geological and reservoir simulation models that will be used to select sites for the demonstration and implementation of CO{sub 2} displacement programs in Part 2. Included in Part 1 is the site selection and drilling of an infill well, coring of the Cypress interval, and injectivity testing to gather information used to update the reservoir simulation model. Part 2 involves field implementation of WAG. Technology Transfer includes outreach activity such as seminars, workshops, and field trips.

Diffusion-bonded NiAl-Al{sub 2}O{sub 3} and Ni{sub 3}Al-Al{sub 2}O{sub 3} couples were thermally fatigued at 900 C for 1500 and 3500 cycles. The fiber-matrix interface weakened after 3500 cycles for the Saphikon fibers, while the Altex, PRD-166, and FP fibers showed little, if any, degradation. Diffusion bonding of fibers to Nb matrix is being studied. Coating the fibers slightly increases the tensile strength and has a rule-of-mixtures effect on elastic modulus. Push-out tests on Sumitomo and FP fibers in Ni aluminide matrices were repeated. Al{sub 2}O{sub 3} was evaporated directly from pure oxide rod onto acoustically levitated Si carbide particles, using a down-firing, rod-fed electron beam hearth; superior coatings were subsequently produced using concurrent irradiation with 200-eV argon ion-assist beam. The assist beam produced adherent films with reduced tensile stresses. In diffusion bonding in B-doped Ni{sub 3}Al matrices subjected to compressive bonding at 40 MPa at 1100 C for 1 hr, the diffusion barriers failed to prevent catastrophic particle- matrix reaction, probably because of inadequate film quality. AlN coatings are currently being experimented with, produced by both reactive evaporation and by N{sup +}-ion enhanced deposition. A 3-kW rod-fed electron-beam-heated evaporation source has been brought into operation.

The fatigue and fracture properties of U6Nb were measured to provide the materials property data needed for structural designs in material processed by solution quenching and aging 200 C/2h. Limited testing was also performed on as-quenched U6Nb. The authors have extended the database on fatigue properties in U6Nb to include both crack initiation data and crack propagation data. The static load carrying capabilities have been characterized through fracture toughness and tensile property measurements. Using a rotating beam fatigue machine, a fatigue strength of 248 MPa was measured at 10{sup 8} cycles for smooth bars at zero mean load. As is typical of nonferrous alloys, U6Nb does not exhibit a fatigue endurance limit. Reductions in fatigue strength for notched bars and for mean loads of 276 MPa and 483 MPa (70 ksi) were also determined. The predominant sites for fatigue crack initiation were identified as niobium carbide and uranium oxide inclusion clusters and the distribution of these inclusions are presented. Fatigue crack propagation rates were measured in the near-threshold regime using compact tension specimens. The fatigue threshold for crack growth rates below 10{sup {minus}7} mm/cycle were measured at both R = 0.1, for which a fatigue threshold of 3.2 MPa{radical}m was …

Experiments have been developed for measuring the rates of chemical reactions liquids and in supercritical Co{sub 2}. A pulsed (Q-switch) Nd:YAG laser at 355 nm was the pump beam for laser flash photolysis studies of molybdenum and tungsten hexacarbonyls undergoing ligand displacement reactions by bidentate chelating agents such as 2,2{prime}-bipyridine in toluene. Experiments were carried out at 0.1 to 150 MPa. In the case of molybdenum complexes, the reaction mechanism for thermal ring closure is found from activation volumes to change from associative interchange to dissociative interchange as substituents on the 2,2{prime}-bipyridine ligands become bulkier. In a similar study of more rigid, substituted phenanthroline bidentate ligands it was found that substituent bulkiness had little effect on the thermal ring closure mechanism. Similar high pressure flash photolysis experiments with tungsten hexacarbonyl have also been completed. The concentration dependence of the fluorescence and nonradiative decay quantum yields for cresyl violet in several solvent have been reported as well as stability constants for the complexation of lithium ion by four different crown ethers dissolved in a room temperature molten salt.

As part of the integrated verification experiment (IVE), we deployed a network of hf ionospheric sounders to detect the effects of acoustic waves generated by surface ground motion following underground nuclear tests at the Nevada Test Site. The network sampled up to four geographic locations in the ionosphere from almost directly overhead of the surface ground zero out to a horizontal range of 60 km. We present sample results for four of the IVEs: Misty Echo, Texarkana, Mineral Quarry, and Bexar.

The United States produced just over 1 billion short tons of coal in 1992, 0.4 percent more than in 1991. Most of the 4-million-short-ton increase in coal production occurred west of the Mississippi River, where a record level of 408 million short tons of coal was produced. The amount of coal received by domestic consumers in 1992 totaled 887 million short tons. This was 7 million short tons more than in 1991, primarily due to increased coal demand from electric utilities. The average price of delivered coal to each sector declined by about 2 percent. Coal consumption in 1992 was 893 million short tons, only 1 percent higher than in 1991, due primarily to a 1-percent increase in consumption at electric utility plants. Consumer coal stocks at the end of 1992 were 163 million short tons, a decrease of 3 percent from the level at the end of 1991, and the lowest year-end level since 1989. US coal exports fell 6 percent from the 1991 level to 103 million short tons in 1992. Less coal was exported to markets in Europe, Asia, and South America, but coal exports to Canada increased 4 million short tons.

With recent theoretical and empirical research in basic and applied psychology, human factors, and engineering, it is now sufficient to define an integrated approach to the deign of advanced displays for present and future nuclear power plants. Traditionally, the conventional displays have shown operators the individual variables on gauges, meters, strip charts, etc. This design approach requires the operators to mentally integrate the separately displayed variables and determine the implications for the plant state. This traditional approach has been known as the single-sensor-single-indicator display design and it places an intolerable amount of mental workload on operators during transients and abnormal conditions. This report discusses a new alternative approach which is the use of direct perception interfaces. Direct perception a interfaces display the underlying physical and system constraints of the situation in a directly perceptual way, such that the viewer need not reason about what is seen to identify system states, but can identify the state of the system perceptually. It is expected that displays which show the dynamics of fundamental physical laws should better support operator decisions and diagnoses of plant states. The purpose of this research project is to develop a suite of direct perception displays for PWR nuclear …

A new reagent, BO-IMI, has been developed that achieves, single step, phosphate specific fluorescence labeling under aqueous conditions. Both 3 in. and 5 in. mononucleotides, including representative DNA adducts can be labeled. Included in this technique is a convenient procedure for postlabeling sample cleanup, leading to a practical detection of the products by capillary electrophoresis with laser fluorescencedetection. We consider that this new method will have a significant impact on the measurement of DNA adducts in human samples. This work was largely accomplished in the second half of our project. In the first half, we set up a new way to isolate DNA nucleotides from blood, worked with an initial, less specific technique for labeling DNA adducts, compared ionizing radiation vs oxidative damage to fluorescein labeled deoxyadenylic acid, and set up a capillary electrophoresis laser fluorescence detection system.

We report improvement of the polarization diagnostics and their use in the development of the Optically Pumped Polarized Ion Source (OPPIS).

Prior to 1988, a variety of materials were buried on the US DOE Oak Ridge Reservation. Records of the disposal operations are incomplete and toxic materials may have been placed adjacent to potential explosives. One of the safety concerns in conducting an environmental restoration project at the burial sites, is the possibility of an explosion which could release toxic materials to the atmosphere. A safety analysis examined the consequences of such releases by first postulating an upper bound for the strength of an explosive. A correlation, developed by Steindler and Seefeldt of Argonne National Laboratory, was then used to estimate the amount and particle-size distribution of the material that could become airborne from the explosion. The estimated amount of airborne material was the source term in an atmospheric dispersion model which was used to calculate infinite-time, concentration-time integrals and 5-minute, time- weighted average concentrations at locations down-wind from the explosion. The dispersion model includes particle deposition as a function of particle-size distribution class. The concentration-time integrals and average concentrations were compared to published guidelines to assess the consequences of an accidental explosion.

Coupon immersion tests were performed on ASTM A537 Class 1 carbon steel in simulated DWPF recycle solutions at 90 {+-} 2{degrees}C, as part of the continuing effort to investigate the formation of shock-sensitive deposits. Coupons were partially immersed for four months in solutions of the same composition used previously at SRTC and at the DuPont Engineering Test Center (a salt solution containing 0.5 M hydroxide and 0.043 M nitrite). Shock-sensitive deposits were not seen on the coupons from this test. There was considerable general corrosion above the water line due to condensate and distilled water contact of the steel. New immersion tests are being planned for completion by September, 1993. The new test solution will reflect the recycle stream chemistry changes brought about by planned ammonia scrubbing in the DWPF.

Structural analyses of large precision cathode strip chambers performed up to the date of this publication are documented. Mechanical property data for typical chamber materials are included. This information, originally intended to be an appendix to the {open_quotes}CSC Structural Design Bible,{close_quotes} is presented as a guide for future designers of large chambers.

The Pennsylvania State University is conducting a superclean coal-water slurry (SCCWS) program for the United States Department of Energy (DOE) and the Commonwealth of Pennsylvania with the objective of determining the capability of effectively firing SCCWS in an industrial boiler designed for heavy fuel oil. Penn State has entered into a cooperative agreement with DOE to determine if SCCWS (a fuel containing coal with 3.0 wt.% ash and 0.9 wt.% sulfur) can effectively be burned in a heavy fuel oil-designed industrial boiler without adverse impact on boiler rating, maintainability, reliability, and availability. The project will provide information on the design of new systems specifically configured to fire these clean coal-based fuels. The project consists of four phases: (1) design, permitting, and test planning, (2) construction and start up, (3) demonstration and evaluation (1,000-hour demonstration), and (4) program expansion (additional 1,000 hours of testing). The boiler testing wig determine if the SCCWS combustion characteristics, heat release rate, fouling and slagging behavior, corrosion and erosion limits, and fuel transport, storage, and handling characteristics can be accommodated in an oil-designed boiler system. In addition, the proof-of-concept demonstration will generate data to determine how the properties of SCCWS and its parent coal affect boiler …