During the 1998 running of the Crystal Ball experiment, a couple of brief test runs were done with the C6 beamline tuned to produce antiprotons. Specifically, one shift on July 29th produced runs 329-334 with the beam momentum set for 650 MeV/c, run 355 was done on July 31st with a 550 MeV/c beam momentum, and run 926-929 were obtained in a single shift on November 3rd, also with a beam momentum of 550 MeV/c. The beam tune for the November data was greatly superior to that of the July data, however. Therefore, only the November data have been analyzed in detail, and the results of this analysis are presented in this note. Due to the paucity of statistics that were obtained, it was decided not to attempt to publish the results. However, the results are valuable as a tool for planning a possible future program of dedicated measurements of antiproton-proton annihilation into all-neutral final states using the Crystal Ball. The data in fact show that the Crystal Ball with its large angular acceptance and multi-photon capability would be an excellent detector for such an experiment. Only one other such experiment (the Crystal Barrel experiment at CERN/LEAR) has ever been …

The objective of this project is to increase oil production and reserves in the Uinta Basin by demonstrating improved completion techniques. Low productivity of Uinta Basin wells is caused by gross production intervals of several thousand feet that contain perforated thief zones and water-bearing zones, and unperforated oil-bearing intervals. Geologic and engineering characterization and computer simulation of the Green River and Wasatch Formations in the Bluebell field will determine reservoir heterogeneities related to fractures and depositional trends. This will be followed by drilling and recompletion of several wells to demonstrate improved completion techniques based on the reservoir characterization. Transfer of the project results will be an ongoing component of the project.

The primary objective of this project is to enhance domestic petroleum production by demonstration and technology transfer of an advanced oil recovery technology in the Paradox basin, southeastern Utah. If this project can demonstrate technical and economic feasibility, the technique can be applied to approximately 100 additional small fields in the Paradox basin alone, and result in increased recovery of 150 to 200 million barrels of oil. This project is designed to characterize five shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation and choose the best candidate for a pilot demonstration project for either a waterflood or carbon dioxide-(CO{sub 2}) flood project. The field demonstration, monitoring of field performance, and associated validation activities will take place in the Paradox basin within the Navajo Nation. The results of this project will be transferred to industry and other researchers through a petroleum extension service, creation of digital databases for distribution, technical workshops and seminars, field trips, technical presentations at national and regional professional meeting, and publication in newsletters and various technical or trade journals. Five activities continued this quarter as part of the geological and reservoir characterization of carbonate mound buildups in the Paradox basin: (1) regional facies evaluation, (2) evaluation …

A liquid mercury target will be used as the neutron source for the proposed Spallation Neutron Source facility. This target is subjected to bombardment by short-pulse, high-energy proton beams. The intense thermal loads caused by interaction of the pulsed proton beam with the mercury create an enormous rate of temperature rise ({approximately}10{sup 7} K/s) during a very brief beam pulse ({approximately } 0.5 {micro}s). The resulting pressure waves in the mercury will interact with the walls of the mercury target and may lead to large stresses. To gain confidence in the mercury target design concept and to benchmark the computer design codes, we tested various electrical and optical sensors for measuring the transient strains on the walls of a mercury container and the pressures in the mercury. The sensors were attached on several sample mercury targets that were tested at various beam facilities: Oak Ridge Electron Linear Accelerator, Los Alamos Neutron Science Center-Weapons Neutron Research, and Brookhaven National Laboratory's Alternating Gradient Synchrotron. The effects of intense background radiation on measured signals for each sensor are described and discussed. Preliminary results of limited tests at these facilities indicate that the fiber optic sensors function well in this intense radiation environment, whereas …

The prospect of using computer simulations to calculate radiation-induced defect production and its influence on microstructure evolution and mechanical property changes during prolonged irradiation of nuclear materials has been a beckoning, yet elusive goal for many years. However, the enormous progress achieved in computational physics for calculating reliable, yet tractable interatomic potentials, coupled with vast improvements in computational power have brought this hope to near reality. In order to develop modeling and simulation tools for predicting the irradiation response of nuclear structural materials, models must be implemented and tested across all relevant length and time scales. We discuss the development and implementation of a modeling methodology that consists of the linkage and hierarchical use of ab initio electronic structure calculations, molecular dynamics (MD) simulations, and kinetic Monte Carlo (KMC) simulations. This methodology can describe length and time scales from nanometers to hundreds of microns and from picoseconds to years, respectively. The ideas are demonstrated in two applications. First, we describe simulations that describe the irradiation and subsequent isochronal annealing of Pb, a low melting point fcc metal, and compare the results to experiments. Second, we show how these methods can be used to investigate damage production and freely migrating defect …

Inelastic nuclear scattering of X-rays from the 14.413 keV nuclear resonance of {sup 57}Fe was employed to measure directly the Fe-projected phonon density of states (DOS) in MBE-grown Fe/Cr(00l) superlattices on MgO(001). The Moessbauer-inactive {sup 56}Fe isotope was used in the Fe layers. A 1{angstrom} thick Moessbauer-active {sup 57}Fe-probe layer (95% enriched) was placed at different locations within the Fe layers. This procedure permits one to distinguish phonon density of states at the Fe-Cr-interface from that at the center of the Fe-film. Distinct differences have been observed in the DOS of our samples. The phonon DOS of an amorphous Tb{sub 33}Fe{sub 67} alloy film was found to be a broad and structureless hump, contrary to that of an epitaxial TbFe{sub 2} film, which exhibits characteristic features.

This Criticality Safety Evaluation Report (CSER) covers the 340 Facility which acts as a collecting point for liquid and solid waste from various facilities in the 300 Area. Criticality safety is achieved by controlling the amount and concentration of the fissionable material sent to the 340 Facility from the originating facilities in the 300 Area, a method similar to that used elsewhere at Hanford for the waste tank farms. Unlike those, however, the waste received at the 340 Facility will be far less radioactive. It is concluded that present operations meet the two contingency criterion. The facility will still be safely subcritical even after two independent and concurrent failures (either of equipment or administrative controls). The solid waste storage and liquid waste will be managed separately. The solid waste storage area is classified as exempt because it contains less than 15 grams of fissionable materials. The Radioactive Liquid Waste System is classified as isolated because it contains less than one third of a minimum critical mass. The criticality safety of the 340 Facility devoted to the Radioactive Liquid Waste System (RLWS) is assured by the form and concentration of the fissile material and could also be classified as a limited …

The objective of this study is to develop and field test a new, integrated Hybrid Hydrologic-Geophysical Inverse Technique (HHGIT) for characterization of the vadose zone at contaminated sites. This new approach to site characterization and monitoring can provide detailed maps of hydrogeological heterogeneity and the extent of contamination by combining information from 3D electric resistivity tomography (ERT) and/or 2D cross borehole ground penetrating radar (XBGPR) surveys, statistical information about heterogeneity and hydrologic processes, and sparse hydrologic data. Because the electrical conductivity and dielectric constant of the vadose zone (from the ERT and XBGPR measurements, respectively) can be correlated to the fluid saturation and/or contaminant concentration, the hydrologic and geophysical measurements are related.

Experiment E769 at Fermilab obtained charm hadroproduction data during the 1987-88 Fixed Target running period with a 250 GeV hadron beam incident on thin target foils of Be, Al, Cu, and W. From an analysis of 25% of the recorded 400M trigger sample we have explored the Feynman x, p{sub t}{sup 2} and the atomic number dependence of charm quark production using samples of D{sup +} and D{sup 0} mesons. 7 refs., 4 figs.

The concentrations of volatile organic compounds (VOCs) and tritium inside of storage domes at TA-54 were measured to assess worker exposure and support the Area G site characterization, including the Radioactive Air Emissions Management (RAEM) program. Samples were collected at 2-3 locations within Domes 48, 49, and 153 on up to six days during the summer of 1994. Samples were collected to evaluate three scenarios: (1) normal working activities with the domes open; (2) after domes were closed overnight; and (3) after domes were closed for three days. Eight-hour integrated samples were collected and analyzed in Radian`s Austin laboratories. Tritium activities from 17.1 to 69,900 pCi/m{sup 3} were measured. About two dozen individual VOCs were identified in each sample, but most of the concentration levels were very low (e.g.; < 1 to 10 ppbv). The highest concentrations measured were bromomethane (56.5 ppbv), 1, 1,1-trichloroethane (75.4 ppbv), propane (958 ppbv), methylene chloride (1,450 ppbv), and toluene (22.8). The measured VOC concentrations were well below the action levels developed by the New Mexico Environment Department and the measured tritium concentrations were well below the DOE`s derived air concentration (DAC). The variability in concentration within a dome during a single sampling episode was …

The objectives of this secondary oil recovery project involving the Carter sandstone in northwest Alabama are: (1) To increase the ultimate economic recovery of oil from the Carter reservoirs, thereby increasing domestic reserves and lessening US dependence on foreign oil; (2) To extensively model, test, and monitor the reservoirs so their management is optimized; and (3) To assimilate and transfer the information and results gathered to other US oil companies to encourage them to attempt similar projects. Start-up water injection began on 0 1/12/93 at the Central Bluff Field, and daily operations began on 01/13/93. These operations include monitoring wellhead pressures at the injector and two producers, and injection water treatment. Water injection was running 200-300 bbl/day at the end of February. Once the unit is pressured-up well testing will be performed. Unitization was approved on 03/01/93.b. For the North Fairview Field correlations and log analyses were used to determine the fluid and rock properties. A summary of these properties is included in Table 1. The results of the log analysis were used to construct the hydrocarbon pore volume map shown on Figure 1. The map was planimetered to determine original oil-in-place (OOIP) values and the hydrocarbon pore volume by …

Anderman/Smith Operating Co. is operating a secondary oil recovery project involving the Carter sandstone in northwest Alabama. The project objectives are: (1) to increase the ultimate economic recovery of oil from the Carter reservoirs, thereby increasing domestic reserves and lessening US dependence on foreign oil; (2) to extensively model, test, and monitor the reservoirs so their management is optimized; and (3) to assimilate and transfer the information and results gathered to other US oil companies to encourage them to attempt similar projects. As a result of waterflood operations at the Central Buff unit, oil production from the Fowler Brasher 7--9 well increased to 40--50 stb/d in late October, and averaged about 45 stb/d in November with no measurable water production. Production at the Fowler Dodson 8--12 was more erratic during the same period. In October, the oil rate for this well increased to nearly 17 stb/d with no reported water production. However, in November the oil production rate declined to about 9 stb/d with an associated average water rate of nearly 17 bpd. Water analysis showed that this produced water was significantly fresher than the connate water produced prior to waterflood operations. This provides evidence for early breakthrough of water …

Multiple current limiting mechanisms exist from the nanometer to millimeter scale in Ag-sheathed (Bi,Pb)-2223 tapes. Recent studies of the zero-field critical current density (J{sub c} (0T, 77K)), the irreversibility field (H*) and the crack microstructure elucidate these properties. We show that H*(77K) can vary significantly over the range {approximately}120-260 mT, independently of J{sub c} (0T, 77K). Cracks, actual or incipient, exist on the sub to several hundred micron scale. Surface magneto optical imaging of whole tapes, correlated to subsequent ultrasonic fracture analysis of. the bare 2223 filaments extracted by dissolving away the Ag shows that even composites having J{sub c} (0T, 77K) values of 60 kA/cm{sup 2} exhibit strong signs of unhealed rolling damage. These combined studies show that today's very best 2223 tapes are still far from full optimization.

The objectives of this secondary oil recovery project involving the Carter sandstone in northwest Alabama are: (1) To increase the ultimate economic recovery of oil from the Carter reservoirs, thereby increasing domestic reserves and lessening US dependence on foreign oil; (2) To extensively model, test, and monitor the reservoirs so their management is optimized; and (3) To assimilate and transfer the information and results gathered to other US oil companies to encourage them to attempt similar projects. Start-up water injection began on 0 1/12/93 at the Central Bluff Field, and daily operations began on 01/13/93. These operations include monitoring wellhead pressures at the injector and two producers, and injection water treatment. Water injection was running 200-300 bbl/day at the end of February. Once the unit is pressured-up well testing will be performed. Unitization was approved on 03/01/93.b. For the North Fairview Field correlations and log analyses were used to determine the fluid and rock properties. A summary of these properties is included in Table 1. The results of the log analysis were used to construct the hydrocarbon pore volume map shown on Figure 1. The map was planimetered to determine original oil-in-place (OOIP) values and the hydrocarbon pore volume by …

The objective is to test the concept that the growth faults in Eugene Island Block 330 (EI-330 field) are conduits through which producing reservoirs are charged and that enhanced production can be developed by producing directly from the fault zone. The site, operated by Penzoil, is located in 250 feet of water and the productive depth intervals include 4000 to 9000 feet. The field demonstration will be accomplished by drilling and production testing of growth fault systems associated with the EI-330 field. The project utilizes advanced 3-D seismic analysis, geochemical studies, structural and stratigraphic reservoir characterization, reservoir simulation, compact visualization systems. In this quarterly report, progress reports are presented for the following tasks: database management; reservoir characterization; modeling; geochemistry; and data integration.

Global Basins Research Network will perform a field demonstration of their ``Dynamic Enhanced Recovery Technology`` to test the concept that the growth of faults in Eugene Island Block 330 (EI-330 field) are conduits through which producing reservoirs are charged and that enhanced production can be developed by producing directly from the fault zone. The site, operated by Penzoil, is located in 250 feet of water and the productive depth intervals include 4000 to 9000 feet. The field demonstration will be accomplished by drilling and production testing of growth fault systems associated with the EI-330 field. The project utilizes advanced 3-D seismic analysis, geochemical studies, structural and stratigraphic reservoir characterization, reservoir simulation, and compact visualization systems. In this quarterly report, progress reports are presented for the following tasks: Task one--management start-up; Task two--database management; Task three--field demonstration experiment; Task four--reservoir characterization; Task five--modeling; Task six--geochemistry; and Task seven--data integration.

This paper has presented the investigation of the mechanism of geopressure occurrence, the transition of elastic properties from the hydrostatic pressured formation to the geopressured formation, and finally, a novel seismic amplitude analysis technique to map the top-of-geopresure surface. The successful application of our new technique to the Pleistocene, offshore Louisiana, Gulf of Mexico has again demonstrated that seismic attributes analyses are of importantance in the hydrocarbon exploration. There are three parts in this paper corresponding to the above discussed topics: Part I discusses mechanisms of geopressuring, and the effects of changing porosity, pressure, and fluid saturation on the elastic properties; Part II investigates the controlling factors in the geopressure transition zone, their seismic responses, and theoretical derivations of our new prediction method; and Part III demonstrates the application of the proposed method to the Pleistocene, Offshore Louisiana, Gulf of Mexico, the prediction discrpepancy between the seismic predicted top-of-geopressure and that dericed from 145 well logs, and finally, the importance of this hydrodynamic surface.

Global Basins Research Network will perform a field demonstration of their ``Dynamic Enhanced Recovery Technology`` to test the concept that the growth faults in EI-330 field are conduits through which producing reservoirs are charged and that enhanced production can be developed by producing directly from the fault zone. The site, operated by Penzoil, is located in 250 feet of water the productive depth intervals include 4000 to 9000 feet. Previous work, which incorporated pressure, temperature, fluid flow, heat flow, seismic, production, and well log data, indicated active fluid flow along fault zones. The field demonstration will be accomplished by drilling and production test of growth fault systems associated with the EI-330 field. The project utilizes advanced 3-D seismic analysis, geochemical studies, structural and stratigraphic reservoir characterization, reservoir simulation, and compact visualization systems. The quarterly progress reports contains accomplishments to date for the following tasks: Management start-up; database management; field and demonstration equipment; reservoir characterization, modeling; geochemistry; and data integration.

The new generation of powerful DSM and SMP cluster computers enables simulations of fluid dynamics at sufficient resolution to compute the complex nonlinear interactions of small-scale turbulent motions with a large-scale driving flow. With a new programming model of hierarchical shared memory multitasking, it is possible to exploit these new systems without disrupting the flow of small and medium-sized jobs that makes their existence possible.

The January 2, 1992 explosion in an electrochemistry laboratory at SRI International (SRI) resulted in the death of scientist Andrew Riley, and gained some notoriety due to its association with experimental work in the controversial field of cold fusion research. Selected components of explosion debris were subjected to forensic analyses at LLNL to elucidate potential causes of, or contributing factors to, the explosion. Interrogation of the debris by LLNL encompassed nuclear, chemical, physical, and materials investigations. Nuclear studies for the determination of tritium and neutron-activation products in stainless steel and brass were negative. No evidence of signature species indicative of orthodox nuclear events was detected. The inorganic and particulate analyses were likewise negative with respect to residues of unexpected chemical species. Such target compounds included conventional explosives, accelerants, propellants, or any exceptional industrial chemicals. The GC-MS analyses of trace organic components in the explosion debris provided perhaps the most interesting results obtained at LLNL. Although no evidence of organic explosives, oxidizers, or other unusual compounds was detected, the presence of a hydrocarbon oil in the interior of the electrochemical cell was established. It is likely that its source was lubricating fluid from the machining of the metal cell components. If …

In September 1994 the DOE Richland Operations Office (RL) approved the FY 1995 multi-year baseline that included a cost estimate of $1.9 billion for FY 1996. However, Congress only appropriated $1.3 billion for that year. The shortfall of $600 million resulted in a significant challenge to accomplish the required workscope. Therefore, RL initiated an aggressive cost savings program to eliminate the shortfall by deleting workscope that was unnecessary and performing the remaining workscope more efficiently. RL initiated baseline planning actions (including deletions, deferrals, transfers, and additions) during the FY 1996 multi-year baseline development process to match workscope and anticipated funding and identified $205 million of workscope deletions. CFR (Contract Finance and Review Division) then reviewed over 200 cost baseline change requests during FY 1996 and documented an additional $95 million of FY 1996 cost savings. This included $73 million of workscope deletions and $22 million of efficiencies. Total savings as a result of FY 1996 initiatives, including baseline planning actions and current year initiatives, were $300 million. This report contains tables which enumerate the savings realized within each program at Hanford.

Cost savings are an integral part of Hanford site operations. Congressional actions towards establishing a balanced budget have resulted in reductions to funding for all federal agencies, including the Department of Energy (DOE) Environmental Management (EM) cleanup mission. In September 1994 the DOE Richland Operations Office (RL) approved the FY 1995 multi-year baseline that included a cost estimate of $1.9 billion for FY 1996. However, Congress only appropriated $1.3 billion for that year. The shortfall of $600 million resulted in a significant challenge to accomplish the required workscope. Therefore, RL initiated an aggressive cost savings program to eliminate the shortfall by deleting workscope that was unnecessary and performing the remaining workscope more efficiently. RL initiated baseline planning actions (including deletions, deferrals, transfers, and additions) during the FY 1996 multi-year baseline development process to match workscope and anticipated funding and identified $205 million of workscope deletions. CFR (Contract Finance and Review Division) then reviewed over 200 cost baseline change requests during FY 1996 and documented an additional $95 million of FY 1996 cost savings. This included $73 million of workscope deletions and $22 million of efficiencies. Total savings as a result of FY 1996 initiatives, including baseline planning actions and current …

Discretization of optimal shape design problems leads to very large nonlinear optimization problems. For attaining maximum computational efficiency, a sequential quadratic programming (SQP) algorithm should achieve superlinear convergence while preserving sparsity and convexity of the resulting quadratic programs. Most classical SQP approaches violate at least one of the requirements. We show that, for a very large class of optimization problems, one can design SQP algorithms that satisfy all these three requirements. The improvements in computational efficiency are demonstrated for a cam design problem.

Setpoints for nuclear safety-related instrumentation are required for actions determined by the design authorization basis. Minimum requirements need to be established for assuring that setpoints are established and held within specified limits. This document establishes the controlling methodology for changing setpoints of all classifications. The instrumentation under consideration involve the transfer, storage, and volume reduction of radioactive liquid waste in the F- and H-Area High-Level Radioactive Waste Tank Farms. The setpoint document will encompass the PROCESS AREA listed in the Safety Analysis Report (SAR) (DPSTSA-200-10 Sup 18) which includes the diversion box HDB-8 facility. In addition to the PROCESS AREAS listed in the SAR, Building 299-H and the Effluent Transfer Facility (ETF) are also included in the scope.