Pulsed Laser Deposition (PLD) has been shown to be an effective method for producing a wide variety of thin films of high-value-added materials. The high average powers and high pulse repetition frequencies of lasers under development at LLNL make it possible to scale-up PLD processes that have been demonstrated in small systems in a number of university, government, and private laboratories to industrially meaningful, economically feasible technologies. A copper vapor laser system at LLNL has been utilized to demonstrate high rate PLD of high quality diamond-like-carbon (DLC) from graphite targets. The deposition rates for PLD obtained with a 100 W laser were {approx} 2000 {mu}m{center_dot}cm{sup 2}/h, or roughly 100 times larger than those reported by chemical vapor deposition (CVD) or physical vapor deposition (PVD) methods. Good adhesion of thin (up to 2 pm) films has been achieved on a small number of substrates that include SiO{sub 2} and single crystal Si. Present results indicate that the best quality DLC films can be produced at optimum rates at power levels and wavelengths compatible with fiber optic delivery systems. If this is also true of other desirable coating systems, this PLD technology could become an extremely attractive industrial tool for high value …

Ambient air monitoring for volatile organic compounds (VOCs) was conducted at TA-54 to characterize non-radioactive air emissions to determine if the Laboratory`s waste operations are releasing significant amounts of VOCs to the ambient environment. Samples were collected at four locations along the northern fenceline (dominant downwind side) of Areas G & L and at a background site located in Bandelier National Monument. Eight-hour integrated samples were collected in evacuated canisters during daylight hours on each of eight days during the summer of 1994, for a total of 40 samples. The samples were analyzed by gas chromatography following EPA Method TO-14 for a target list of 68 analytes. In general, about two dozen volatile organic compounds (VOCs) were identified in each sample, including those collected at the background site, but the concentration levels were very low (e.g.; < 1 to 10 ppbv). The average total non-methane hydrocarbon (TNMHC) concentration ranged from 4.3 to 22.8 ppbv at the Area G and L sites as compared with an average of 4.2 ppbv at the background site. The measured concentrations were compared with action levels developed by the New Mexico Environment Department and were well below the action levels in all cases. Methanol and …

It may be possible to surround the region where fusion reactions are taking place with a neutronically thick liquid blanket which has penetrations that allow only a few tenths of a percent of the neutrons to leak out. Even these neutrons can be attenuated by adding an accurately placed liquid or solid near the target to shadow-shield the beam ports from line-of-sight neutrons. The logic of such designs are discussed and their evolution is described with examples applied to both magnetic and inertial fusion (HYLIFE-II). These designs with liquid protection are self healing when exposed to pulsed loading and have a number of advantages-over the usual designs with solid first walls. For example, the liquid-protected solid components will last the life of the plant, and therefore the capacity factor is estimated to be approximately 10% higher than for the non-liquid-walled blankets, because no blanket replacement shutdowns are required. The component replacement, operations, and maintenance costs might be half the usual value because no blanket change-out costs or accompanying facilities are required. These combined savings might lower the cost of electricity by 20%. Nuclear-grade construction should not be needed, largely because the liquid attenuates neutrons and results in less activation of …

The Department of Energy (DOE) has more than 2.5 million tons of radioactive scrap metal (RSM) that is either in inventory or expected to be generated over the next 25 years as major facilities within the weapons complex are decommissioned. Much of this material cannot be surface decontaminated. In an attempt to conserve natural resources and to avoid burial of this material at DOE disposal sites, options are now being explored to {open_quotes}beneficially reuse{close_quotes} this material in applications where small amounts of radioactivity are not a detriment. One example is where RSM is currently being beneficially used to fabricate shield blocks for use in DOE medium energy physics programs. This paper describes other initiatives now underway within DOE to utilize RSM to fabricate other products, such as radioactive waste shipping, storage and disposal containers.

This report briefly discusses the following topics: quark-gluon plasma and high-energy collisions; hadron structure and chiral dynamics; nonperturbative studies and nonabelian gauge theories; and studies in quantum field theory.

Waste analysis plan for the double shell tanks. SD-WM-EV-053 is Superseding SD-WM-EV-057.This document provides the plan for obtaining information needed for the safe waste handling and storage of waste in the Double Shell Tank Systems. In Particular it addresses analysis necessary to manage waste according to Washington Administrative Code 173-303 and Title 40, parts 264 and 265 of the Code of Federal Regulations.

This report is a compilation of submitted abstracts of scientific papers presented at the second Department of Energy-supported workshop on the use and applications of biomarkers held in Santa Fe, New Mexico, from April 26--29, 1994. The abstracts present a synopsis of the latest scientific developments in biomarker research and how these developments meet with the practical needs of the occupational physician as well as the industrial hygienist and the health physicist. In addition to considering the practical applications and potential benefits of this promising technology, the potential ethical and legal ramifications of using biomarkers to monitor workers are discussed. The abstracts further present insights on the present benefits that can be derived from using biomarkers as well as a perspective on what further research is required to fully meet the needs of the medical community.

The Actinide Source Term represents the quantity of actinides that could be mobilized within WIPP brines and could migrate with the brines away from the disposal room vicinity. This document presents the various proposed methods for estimating this source term, with a particular focus on defining these methods and evaluating the defensibility of the models for mobile actinide concentrations. The conclusions reached in this document are: the 92 PA {open_quotes}expert panel{close_quotes} model for mobile actinide concentrations is not defensible; and, although it is extremely conservative, the {open_quotes}inventory limits{close_quotes} model is the only existing defensible model for the actinide source term. The model effort in progress, {open_quotes}chemical modeling of mobile actinide concentrations{close_quotes}, supported by a laboratory effort that is also in progress, is designed to provide a reasonable description of the system and be scientifically realistic and supplant the {open_quotes}Inventory limits{close_quotes} model.

We suggest that the derivation of the free space Maxwell Equations for classical electromagnetism, using a discrete ordered calculus developed by L.H. Kauffman and T. Etter, necessarily pushes the discussion of determinism in natural science down to the level of relativistic quantum mechanics and hence renders the mathematical phenomena studied in deterministic chaos research irrelevant to the question of whether the world investigated by physics is deterministic. We believe that this argument reinforces Suppes` contention that the issue of determinism versus indeterminism should be viewed as a Kantian antinomy incapable of investigation using currently available scientific tools.

Data centers routinely archive and distribute large databases of high quality and with rigorous documentation but, to meet the needs of global studies effectively and efficiently, data centers must go beyond these traditional roles. Global studies of environmental change require integrated databases of multiple data types that are accurately coordinated in terms of spatial, temporal and thematic properties. Such datasets must be designed and developed jointly by scientific researchers, computer specialists, and policy analysts. The presentation focuses on our approach for organizing data from ground-based research programs so that the data can be linked with remotely sensed data and other map data into integrated databases with spatial, temporal, and thematic characteristics relevant to global studies. The development of an integrated database for Net Primary Productivity is described to illustrate the process.

While CIAC periodically issues bulletins about specific computer viruses, these bulletins do not cover all the computer viruses that affect desktop computers. The purpose of this document is to identify most of the known viruses for the MS-DOS and Macintosh platforms and give an overview of the effects of each virus. The authors also include information on some windows, Atari, and Amiga viruses. This document is revised periodically as new virus information becomes available. This document replaces all earlier versions of the CIAC Computer virus Information Update. The date on the front cover indicates date on which the information in this document was extracted from CIAC`s Virus database.

The authors investigated the decomposition of HMX or PBX-9404 as a 25% solution in DMSO by treatment with aqueous base solutions. They investigated investigated two concentrations of NaOH solutions, 40% NaOH and 2N NaOH. {sup 1}H-nmr spectroscopy was chosen to follow the decomposition by {sup 1}H-nmr spectroscopy, watching the disappearance of the -CH{sub 2}-absorbance of HMX at 6.2 ppm. The 40% NaOH solution is initially immiscible with the DMSO solution but becomes miscible as it reacts. The reaction is exothermic with recorded temperatures after mixing reaching 90{degrees}C. The mixture does foam somewhat but this can be controlled by slowing down the stirring speed. The 2N NaOH solution is miscible with the HMX/DMSO solution but upon mixing the HMX is precipitated by the water present in the base solution. The mixing of the solutions is much less exothermic and the decomposition is slower than the 40% NaOH solution so the mixture is heated at 60{degrees}C for 1h to facilitate the decomposition.

Array class libraries have the potential to support development of a broad class of scientific computations. The high level array syntax coupled with machine dependent internal routines simplifies the structure of scientific codes and hides the details of particular machine architectures. Unfortunately, array class libraries generally suffer from recurring performance problems, making their use on high performance computers difficult to justify. In this paper, we discuss these performance issues for array class libraries and propose optimizations within A++/P++ to address them. Deferred evaluation in A++/P++ provides the information required for these optimizations. We present performance results on example finite difference computations which show that these performance problems can be overcome within array class libraries. The optimizations are equally applicable to more general scientific computations, thus establishing array class libraries as a viable program development strategy for scientific codes.

This acceptance test procedure (ATP) was written to test the void fraction instrument (VFI) and verify that the unit is ready for field service. The procedure verifies that the mechanical and electrical features (not specifically addressed in the software ATP) and software alarms are operating as designed.

A summary of the attractive characteristics of mirror devices is presented. Recent progress in development of axisymmetric mirror devices is described. Potentialities of mirrors as a basis for D{sup 3}He fusion power generators and high-flux neutron sources for fusion material tests are discussed.

Westinghouse Hanford Company has contracted Los Alamos Technical Associates to listing of vapors and aerosols that are or may be emitted from the High Level Waste (HLW) tanks at Hanford. Mitigation requirements under Federal and State law, as well as DOE Orders, are included in the listing. The lists will be used to support permitting activities relative to tank farm ventilation system up-grades. This task is designated Task 108 under MJB-SWV-312057 and is an extension of efforts begun under Task 53 of Purchase Order MPB-SVV-03291 5 for Mechanical Engineering Support. The results of that task, which covered only thirty-nine tanks, are repeated here to provide a single source document for vapor mitigation requirements for all 177 HLW tanks.

United States industry has a critical need for materials that are lightweight, strong, tough, corrosion resistant and capable of performing at high temperatures; such materials will enable substantial increase in energy efficiency and reduction in emissions of pollutants. Continuous fiber ceramic composites (CFCCs) are an emerging class of materials which have the potential for the desired combination of properties to meet the industrial needs. A $10 billion annual market has been estimated for CFCC products by the year 2010, which equates to over 100,000 industrial sector jobs. The CFCC program began in the spring of 1992 as a three-phase 10-year effort to assess potential applications of CFCC materials, develop the necessary supporting technologies to design, analyze and test CFCC materials, conduct materials and process development guided by the applications assessment input, fabricate test samples and representative components to evaluate CFCC material capabilities under application conditions, and analyze scaleability and manufacturability plus demonstrate pilot-scale production engineering. DOE awarded 10 Phase I cooperative agreements to industry-lead teams plus identified generic supporting technology projects. This document highlights the broad progress and accomplishments on these contracts and support technology projects during Phase I.

Of particular concern to facilities on the Hanford site is Title 40, Code of Federal Regulations, Chapter 40, Part 61, Subpart H, ``National emission Standards for Emissions of Radionuclides Other Than Radon From Department of Energy Facilities.`` Assessments of facility stacks and potential radionuclide emissions determined whether these stacks would be subject to the sampling and monitoring requirements of 40 CFR 61, Subpart H. Stack 296-B-5 exhausts 221-BB building which houses tanks containing B Plant steam condensate and B Plant process condensate from the operation of the low-level waste concentrator. The assessment of potential radionuclide emissions from the 296-B-5 stack resulted in an effective dose equivalent to the maximally exposed individual of less than 0.1 millirem per year. Therefore, the stack is not subject to the sampling and monitoring requirements of 40 CFR 61, Subpart H. However, the sampling and monitoring system must be in compliance with the Environmental Compliance Manual, WHC-CM-7-5. Currently, 296-B-5 is sampled continuously with a record sampler and continuous air monitor (CAM).

Atomic transport of oxygen in nonstoichiometric oxides is an extremely important topic which overlaps science and technology. In many cases the diffusion of oxygen controls sintering, grain growth, and creep. High oxygen diffusivity is critical for efficient operation of many fuel cells. Additionally, oxygen diffusivities are an essential ingredient in any point defect model. Secondary Ion Mass Spectrometry (SIMS) is the most accurate modern technique to measure oxygen tracer diffusion. This paper briefly reviews the principles and applications of SIMS for the measurement of oxygen transport. Case studies are taken from recent work on ZnO and some high-temperature superconductors.

This report contains brief papers on the research being conducted at the Institute of Geophysics and Planetary Physics in 1993 in Geosciences, High-Pressure sciences, and Astrophysics.

The purpose of the HEIS Field Quality Control subject area is to manage the data acquired from field quality control samples. Field quality control samples are used to determine if sample contamination has occurred at some point in the sampling process. Four major types of data comprise the Field Quality Control subject area. Data about samples, spike samples, chemical and/or radiologic analysis of field quality control samples, and relationships between field quality control and non-quality control samples.

The effect of transition metal (TM) substitution for Pd in Ti{sub 5O}Pd{sub (50-x}TM{sub x} alloys with x between 5 and 37.5 at.% and TM = V, Cr, Mn and Fe are being characterized by transmission electron microscopy and First-Principles Alloy Theory modeling. The goal is to obtain detailed structural information related to the ternary phase relations and transformations that are necessary for effective shape-memory alloy development. Thus far, the authors have found that the tend to have pseudobinary eutectoid-like configurations with a terminal TiPd and a non-close-packed long period ordered structure type crystal structure) based on the stoichiometry Ti{sub 2}PdTM. The systems exhibit a conventional martensitic transformation, as well as a new type of displacive transformation that shear-modulates B2 to produce a periodically distorted, but non-close-packed metastable product phase.

None

This Statement of Work describes the Architect-Engineer services to be provided by Raytheon/BNFL in providing a conceptual design (Contract TGW-SVV-063869) for the Initial Pretreatment Module (IPM), Project W-236B, at the Hanford site, Richland, Washington. The IPM Project, a radiochemical process facility, will be designed and constructed for an initial phase of waste pretreatment, which will be for the removal of cesium from supernatant wastes to produce a Low-level waste (LLW) stream to a vitrification facility. The design shall also accommodate side streams of High-Level Waste (HLW) fractions that will be directed to suitable, existing storage tanks where they will be recombined with an additional high-activity waste fraction generated from pretreatment of the tank waste sludges and solids. This combined high-activity waste fraction will be immobilized as glass and disposed in a geological repository.