We describe a simple method to predict the transient response of variable impedance stripline to pulse excitation. The method uses a finite difference based, quasi-static impedance formulation to calculate the reflection coefficient at each point along the direction of pulse propagation and the subsequent short pulse behavior of a variable impedance structure. A Fortran computer program is written to determine the quasi-static impedance. Excellent agreement of better than 1% between the finite difference impedance predictions and experimental results is noted. A second computer program is written utilizing previous results but essentially incorporating reflection and transmission from several discontinuities to analyze the transient response of the structure. This transient analysis yields good agreement between predictions and results obtained by means of time domain reflectometry.

This thesis describes the design, development, and testing of a search system for supernovae, based on the use of current computer and detector technology. This search uses a computer-controlled telescope and charge coupled device (CCD) detector to collect images of hundreds of galaxies per night of observation, and a dedicated minicomputer to process these images in real time. The system is now collecting test images of up to several hundred fields per night, with a sensitivity corresponding to a limiting magnitude (visual) of 17. At full speed and sensitivity, the search will examine some 6000 galaxies every three nights, with a limiting magnitude of 18 or fainter, yielding roughly two supernovae per week (assuming one supernova per galaxy per 50 years) at 5 to 50 percent of maximum light. An additional 500 nearby galaxies will be searched every night, to locate about 10 supernovae per year at one or two percent of maximum light, within hours of the initial explosion.

Three documents constitute the executive summary series in Data Package III: this document (Documentation Overview and Tables of Contents (E001)) plus the AVLIS Production Plant Executive Summary (E010) and the AVLIS Production Plant Overall Design Report (E020). They provide progressively greater detail on the key information and conclusions contained within the data package. The Executive Summary and Overall Design Report present summaries of each Data Package III document. They are intended to provide a global overview of AVLIS Production Plant deployment including program planning, project management, schedules, engineering design, production, operations, capital cost, and operating cost. The purpose of Overview and Tables of Contents is threefold: to briefly review AVLIS goals for Data Package III documentation, to present an overview of the contents of the data package, and to provide a useful guide to information contained in the numerous documents comprising the package.

This document deals with the procurements planned for the construction of an Atomic Vapor Laser Isotope Separation (AVLIS) production plant. Several large-scale AVLIS facilities have already been built and tested; a full-scale engineering demonstration facility is currently under construction. The experience gained from these projects provides the procurement basis for the production plant construction and operation. In this document, the status of the AVLIS process procurement is presented from two viewpoints. The AVLIS Production Plant Work Breakdown Structure is referenced at the level of the items to be procured. The availability of suppliers for the items at this level is discussed. In addition, the work that will result from the AVLIS enrichment plant project is broken down by general procurement categories (construction, mechanical equipment, etc.) and the current AVLIS suppliers are listed according to these categories. A large number of companies in all categories are currently providing AVLIS equipment for the Full-Scale Demonstration Facility in Livermore, California. These companies form an existing and expanding supplier network for the AVLIS program. Finally, this document examines the relationship between the AVLIS construction project/operational facility and established commercial suppliers. The goal is to utilize existing industrial capability to meet the needs of the …

This preliminary Quality Assurance Plan and Assessment establishes the Quality Assurance requirements for the AVLIS Production Plant Project. The Quality Assurance Plan defines the management approach, organization, interfaces, and controls that will be used in order to provide adequate confidence that the AVLIS Production Plant design, procurement, construction, fabrication, installation, start-up, and operation are accomplished within established goals and objectives. The Quality Assurance Program defined in this document includes a system for assessing those elements of the project whose failure would have a significant impact on safety, environment, schedule, cost, or overall plant objectives. As elements of the project are assessed, classifications are provided to establish and assure that special actions are defined which will eliminate or reduce the probability of occurrence or control the consequences of failure. 8 figures, 18 tables.

The AVLIS Production Plant is designated as a Major System Acquisition (in accordance with DOE Order 4240.IC) to deploy Atomic Vapor Laser Isotope Separation (AVLIS) technology at the Oak Ridge, Tennessee site, in support of the US Uranium Enrichment Program. The AVLIS Production Plant Project will deploy AVLIS technology by performing the design, construction, and startup of a production plant that will meet capacity production requirements of the Uranium Enrichment Program. The AVLIS Production Plant Project Management Plan has been developed to outline plans, baselines, and control systems to be employed in managing the AVLIS Production Plant Project and to define the roles and responsibilities of project participants. Participants will develop and maintain detailed procedures for implementing the management and control systems in agreement with this plan. This baseline document defines the system that measures work performed and costs incurred. This plan was developed by the AVLIS Production Plant Project staff of Martin Marietta Energy Systems, Inc. and Lawrence Livermore National Laboratory in accordance with applicable DOE directives, orders and notices. 38 figures, 19 tables.

An AVLIS Production Plant Deployment Schedule for the engineering, procurement, and construction for both the Initial Increment of Production and the fully Activated Plant, has been developed by the project team consisting of Lawrence Livermore National Laboratory, Martin Marietta Energy Systems, Inc. with architect-engineer support from Bechtel National, Inc., Stone and Webster Engineering Corporation, and Westinghouse Corporation. The initial deployment phase consists of six separators modules and the three laser power amplifier modules consistent with the FY84 reference design with a name plate capacity of 5 million separative work units/yr followed by a full plant activation to approximately 13 million separative work units/yr. The AVLIS Production Plant project team's strategy for deployment schedule analysis focused on three schedule options: engineering limited schedule; authorization limited schedule; and funding limited project schedule. The three deployment schedule options developed by AVLIS project team have been classified in ranges such as an optimistic, rapid/moderate, or moderate/pessimistic based on the probability of meeting the individual schedule option's major milestones or program objectives of enriching uranium by the AVLIS process in an effective cost and schedule manner. 47 figures, 7 tables.

Following the executive summary, this document contains the following: (1) waste management facilities design objectives; (2) AVLIS production plant wastes; (3) waste management design criteria; (4) waste management plan description; and (5) waste management plan implementation. 17 figures, 18 tables.

The work breakdown structure has been prepared for the AVLIS Production Plant to define, organize, and identify the work efforts and is summarized in Fig. 1-1 for the top three project levels. The work breakdown structure itself is intended to be the primary organizational tool of the AVLIS Production Plant and is consistent with the overall AVLIS Program Work Breakdown Structure. It is designed to provide a framework for definition and accounting of all of the elements that are required for the eventual design, procurement, and construction of the AVLIS Production Plant. During the present phase of the AVLIS Project, the conceptual engineering phase, the work breakdown structure is intended to be the master structure and project organizer of documents, designs, and cost estimates. As the master project organizer, the key role of the work breakdown structure is to provide the mechanism for developing completeness in AVLIS cost estimates and design development of all hardware and systems. The work breakdown structure provides the framework for tracking, on a one-to-one basis, the component design criteria, systems requirements, design concepts, design drawings, performance projections, and conceptual cost estimates. It also serves as a vehicle for contract reporting. 12 figures, 2 tables.

In this note, we describe a design of lattice, which is by no means optimized for the ultimate performance, but these parameters can be used for the starting point of other design efforts. Assumptions and features used in this design are: (1) 32 periods which is reasonably high periodicity for chromaticity corrections. (2) Achromatic bending cell which enables us to make all straight sections to be dispersion free. (3) Twiss parameters at dispersion area are the same for all cells to make undulator straight section can be tuned to wiggler straight section a-id vice versa. (4) No attempt is made to extract the photon beam from bending magnets, and when this feature is added, the lattice design may have to be changed in order to provide-the photon beam channel. (5) Natural emittance in the horizontal plane is made as small as possible in the range of 10-8m radians. This value can be optimized later by judicious choice of the Twiss parameters through the bending magnets. (6) The bending magnet should have parallel edges in order to simplify its construction. This assumption implies that there is vertical focussing from the edge. (7) The beta functions at the straight section should be …

IRAD GAGE vibrating-wire stressmeters were installed in the Spent Fuel Facility at the Nevada Test Site to measure the change in in-situ stress during the Spent Fuel Test-Climax (SFT-C). Although extensive pre-installation laboratory tests were conducted, they were generic in nature. Unfortunately the degree of gage-rock contact has a strong influence on gage sensitivity and cannot be predicted before installation. This report discusses the results of removing a cylindrical section of rock and gages as a unit through overcoring and the subsequent post test calibrations of the stressmeters in the laboratory. With the assumption that the gage-rock contact was not disturbed by the overcoring, the results from these calibrations compensate for varying gage-rock contact. The estimated in-situ stresses based on post test calibration data are quite consistent with those directly measured in nearby holes. The magnitude of stress change calculated from pre-installation test data is generally much smaller than that estimated from post test calibration data.

This paper identifies some of the issues which arise in the consideration of the derivation of new limits on exposure to internal emitters. Basic and secondary radiation protection limits are discussed. Terms are defined and applied to the limitation of risk from stochastic effects. Non-stochastic data for specific internal emitters (/sup 131/I and the radium isotopes) are presented. Emphasis is placed on the quantitative aspects of the limit setting problem. 65 references, 2 figures, 12 tables.

Electrical characterization of defects induced in FZ and CZ silicon stress in four-point bending above 1200/sup 0/C has been started. Techniques to study electrical activity that will permit correlation of defect activity with diffusion length and with room and low temperature EBIC are being developed. Preliminary characterization of defects in ribbon grown at very low speeds of less than 1 cm/min shows that the dislocation density is very low over significant regions of cross section, while regions of high dislocation density (approx. 5 x 10/sup 6//cm/sup 2/) occur in bands in a number of places. Additional measurements of stress distributions in EFG material have been obtained at the University of Illinois using shadow-Moire interferometry.

The Argonne National Laboratory and Sandia National Laboratory have recently installed an activated barrier, the Access Denial System (ADS) for the upgrade of safeguards of special nuclear materials. The technology of this system was developed in the late 70's by Sandia National Laboratory-Albuquerque. The installation was the first for the Department of Energy. Subsequently, two additional installations have been completed. The Access Denial System, combined with physical restraints, provide the system delay. The principal advantages of the activated barrier are: (1) it provides an order of magnitude improvement in delay over that of a fixed barrier, (2) it can be added to existing vital areas with a minimum of renovations, (3) existing operations are minimally impacted, and (4) health and safety risks are virtually nonexistent. Hardening of the vital areas using the ADS was accomplished in a cost-effective manner. 3 references, 1 figure, 1 table.

The polyperfluoroethers are compatible with uranium hexafluoride (UF/sub 6/) and are suitable for use in diffusion pumps and in mechanical vacuum pumps which rely on oil as both the lubricant and the seal. The UF/sub 6/ is soluble in all fluids with which it is compatible. Because a number of vacuum pumps in the BOP facilities of the GCEP plant employ these perfluoroether oils as the working fluid and have oil chambers which are large, questions have been raised as to the relationships governing the solubility of UF/sub 6/ in these materials and the maximum quantities of UF/sub 6/ which could be dissolved in these oils under credible accident conditions. This report summarizes these solubility relations and the interaction of the UF/sub 6/ solubility and the pumping capability of this type of vacuum pump. It will be shown that, whereas the solubility of UF/sub 6/ in Fomblin Y25 fluoroether fluid under a UF/sub 6/ pressure of 760 torr and at the pump operating temperature of 160/sup 0/F is about 500 g of UF/sub 6/ per liter of oil, the system controls are such as to isolate the system from the pumps before the quantity of UF/sub 6/ dissolved in the …

Four-point bending studies have been continued to compare primary creep response of FZ and CZ silicon above 1200/sup 0/C. Results suggest that silicon can be treated as a completely plastic solid in the temperature range 1200 to 1400/sup 0/C in its response to thermal stress generated during sheet growth. In the stress range of 5 to 15 MPa, the strain rate dependence on stress is epsilon approx. sigma/sup 10/, and appears to be essentially temperature independent. Work is underway to compare stresses predicted for two different thermal models used for temperature field calculations. Stress analysis has been performed to illustrate the dependence of sheet stresses on growth parameters such as sheet width, thickness and growth speed, and the coupling of these parameters to the details of the temperature field calculations used as input to the stress model. The construction of a simplified EFG ribbon system to be used to test the stress model and to investigate means to achieve low stress growth configurations is completed. The first results of measurement of residual stress distributions in EFG sheet using shadow-Moire interferometry have been obtained at the University of Illinois.

Results pertaining to the recently modified beam-injection arrangement in the central cell of TMX-U are presented here. These modifications followed our observation that beam atoms injected perpendicular to the magnetic axis between the first two magnet-coil gaps give rise to trapped ions with midplane pitch angles lying in the intervals 68/sup 0/ < theta < 78/sup 0/ and 59/sup 0/ < theta < 65/sup 0/. These pitch-angle intervals are similar in value to the earlier arrangement of beams injected at the midplane at pitch angles of 58 and 70/sup 0/. Normal injection at an off-midplane position has two advantages when compared with off-normal injection at the midplane. First, the unattenuated beam can be dumped in the first-injector region rather than in the plasma region. Second, the beams can be oriented with their long dimension horizontal rather than vertical. The first point al

This report describes calculations and analysis performed in an attempt to provide a new estimate for the yield of the Hiroshima weapon. Newly discovered meteorological data was adapted for use in one- and two-dimensional hydrodynamic codes, and a series of calculations was then run for different values of yield. The objective was to determine what yield produced an overpressure record which could best be correlated with an actual trace measured at a parachute-dropped canister. Altitude of the bomb and canister-carrying aircraft at drop time was also a variable parameter. The analysis provides an estimate of 16.6 + 0.3 kt for the yield of the Hiroshima weapon. A drop altitude of near 35,500 feet is shown to be consistent with the signal time-of-arrival. This yield value is within the range of other estimates, but the drop altitude is higher than that previously assumed to be reasonable.

The dissolution of plutonium dioxide in nitirc acid (HNO/sub 3/) at high hydrofluoric acid (HF) concentrations has been investigated. Dissolution rate curves were obtained using 12M HNO/sub 3/ and HF at concentrations varying from 0.05 to 1.0 molar. The dissolution rate increased with HF concentration up to 0.2M and then decreased at higher concentrations. There was very little plutonium dissolved at 0.7 and 1.0M HF because of the formation of insoluble PuF/sub 4/. Various oxidizing agents were added to 12M HNO/sub 3/-1M HF dissolvent to oxidize Pu(IV) to Pu(VI) and prevent the formation of PuF/sub 4/. Ceric (Ce(IV)) and silver (Ag(II)) ions were the most effective in dissolving PuO/sub 2/. Although these two oxidants greatly increased the dissolution rate, the rates were not as rapid as those obtained with 12M HNO/sub 3/-0.2M HF.

This subgroup has focussed on detectors for fixed target experiments which have full azimuthal coverage. The general scope of the working group was to consider (1) the configuration of an idealized detector, and (2) various configurations of practical detectors that could be implemented on a relatively short time scale. The second category includes possible upgrades and modifications of existing experimental facilities. Beams of both 15 GeV/A sulphur at the AGS and 200 GeV/A oxygen at the SPS were considered.

This report presents research results in the areas of industrial hygiene, radiation protection, fire safety, and instrument development. Items have been individually abstracted. (ACR)

A simple graphical method has been developed to undertake technical design trade-off studies for individual parabolic dish modules comprising a two-axis tracking parabolic dish with a cavity receiver and power conversion assembly at the focal point. The results of these technical studies can then be used in performing the techno-economic analyses required for determining appropriate subsystem sizing. Selected graphs that characterize the performance of subsystems within the module have been arranged in the form of a nomogram that would enable an investigator to carry out several design trade-off studies. Key performance parameters encompassed in the nomogram include receiver losses, intercept factor, engine rating, and engine efficiency. Design and operation parameters such as concentrator size, receiver type (open or windowed aperture), receiver aperture size, operating temperature of the receiver and engine, engine partial load characteristics, concentrator slope error, and the type of reflector surface, are also included in the graphical solution. Cost considerations are not included. The nomogram has been used to perform trade-off studies that have provided a basis for determining requirements for a single concentrator that could perform satisfactorily with either the selected Stirling or Brayton engine. This activity is summarized to illustrate the usage of the nomogram. Additionally, …

Over the years the study of the confinement of high temperature plasma in magnetic mirror systems has presented researchers with many unusual physics problems. Many of these issues are by now understood theoretically and documented experimentally. With the advent of the tandem mirror idea, some new issues have emerged and are now under intensive study. These include: (1) the generation and control of ambipolar confining potentials and their effect on axial confinement and, (2) the combined influence of nonaxisymmetric magnetic fields (used to ensure MHD stability) and electric magnetic particle drifts on radial transport. Physics considerations associated with these two categories of issues will be reviewed, including concepts for the control of radial transport, under study or proposed.

This report summarizes the results of an industry survey made during the summer of 1983. The survey was initiated in order to develop an information base on advanced engines that could be used in the solar thermal dish-electric program. Questionnaires inviting responses were sent to 39 companies known to manufacture or integrate externally heated engines. Follow-up telephone communication ensured uniformity of response.