The Lassen hydrothermal system is in the southern Cascade Range, approximately 70 kilometers east-southeast of Redding, California. The conceptual model of the Lassen system is termed a liquid-dominated hydrothermal system with a parasitic vapor-dominated zone. The essential feature of this model is that steam and steam-heated discharge at relatively high elevations in Lassen Volcanic National Park (LVNP) and liquid discharge with high chloride concentrations at relatively low elevations outside LVNP in the Lassen Known Geothermal Resource Area (KGRA) are both fed by an upflow of high-enthalpy, two-phase fluid within the Park. Liquid flows laterally away from the upflow area towards the areas of high-chloride discharge, and steam rises through a vapor-dominated zone to feed the steam and steam-heated features. The geometric model corresponds to an areally restricted flow regime that connects the Bumpass Hell area in LVNP with regions of chloride hot springs in the Mill Creek canyon in the KGRA south of LVNP. Simulations of thermal fluid withdrawal in the Mill Creek Canyon were carried out in order to determine the effects of such withdrawal on portions of the hydrothermal system within the Park. 19 refs., 17 figs., 4 tabs.

Damage nucleation in single crystals of silicon during ion irradiation is investigated. Experimental results and mechanisms for damage nucleation during both room and liquid nitrogen temperature irradiation with different mass ions are discussed. It is shown that the accumulation of damage during room temperature irradiation depends on the rate of implantation. These dose rate effects are found to decrease in magnitude as the mass of the ions is increased. The significance of dose rate effects and their mass dependence on nucleation mechanisms is discussed.

Microscopic and semi-classical descriptions of octupole deformation are compared. New semi-classical results, obtained with the use of a Woods-Saxon potential are presented. Comparisons with experiment are made. 21 references.

The ATF experiment will test improvements to high-beta, steady-state toroidal confinement using external helical fields. The device design has been optimized to (1) provide direct access to the high-beta second-stability regime, (2) have sufficient flexibility to study a large range of toroidal configurations both with and without plasma current, (3) test the reduction of low-collisionality transport by EXB drifts induced by the self-consistent radial electric field, and (4) permit steady-state, high-beta operation without disruptions. Continued physics studied at ORNL and recent results from foreign stellarator experiments have increased confidence in ATF performance.

As part of the safety assessment in the design of the glass melter for large-scale immobilization of high-level radioactive wastes, structural considerations of the containment shell include its dynamic responses to abnormal loading conditions such as that caused by a steam explosion. The postulated steam explosion, conservatively given an energy content equivalent to 13 pounds of TNT, is capable of exerting sudden pressures greater than 300 psi but less than 410 psi on the melter wall. By use of thin-shell theory, the equations of motion satisfying the discontinuity conditions at junctions of shells with different curvatures are solved analytically. Results of stress analysis ensure elastic responses of the containment structure of the melter. 6 references, 3 figures, 1 table.

Based on the upper-bound theorem in limit analysis, a theoretical model describing sound flow, core fracture, and sleeve fracture in bimetal rods and wire during extrusion and drawing was developed. The variables affecting core and sleeve fracture are: reduction in area, die geometry, friction, relative size and strength of the core, and applied surface tractions. Within the wide range of combinations of these process variables, only a small range permits co-extrusion and codrawing without fracture. Criteria for the prevention of core and sleeve fracture during co-extrusion and core fracture during co-drawing were developed and presented graphically in this study. The results were applied to the central burst problem during extrusion and drawing of homogeneous materials.

The most common asbestos materials used at the Savannah River site include: steam pipe insulation; powerhouse boiler insulation; wallboards; roofing materials; and cement products. Asbestos was also found in a number of other materials: aprons; gaskets; laboratory hot pads; and talcum powder used for gloves. Techniques for removal; personnel training; mechanical ventilation; and personnel isolation techniques are described for completing asbestos removal safely and without boiler downtime. (PSB)

This report is a description of the present Linac distributed control system that replaces the original Xerox computer and interface electronics with a network of 68000-based stations. In addition to replacing the obsolete Xerox equipment, goals set for the new system were to retain the fast response and interactive nature of the original system, to improve reliability, to ease maintenance, and to provide 15 Hz monitoring of all Linac parameters. Our previous experience with microcomputer installations showed that small, stand-alone control systems are rather straightforward to implement and have been proven to be reliable in operation, even in the severe environment of the 750-keV preaccelerator. The overall design of the Linac system incorporates the concept of many relatively small, stand-alone control systems networked together using an intercomputer communication network. Each station retains its local control system character but takes advantage of the network to allow an operator to interact with the entire Linac from any local console. At the same time, a link to the central computer system allows Host computers to also access parameters in the Linac.

A review is given on current neutron scattering experiments at Brookhaven National Laboratory on transition-metal ferromagnets Ni, Fe, Pd/sub 2/MnSn and MnSi. The scattering intensity in constant-energy scans, observed above T/sub c/ in all of these materials, exhibited a clear peak at finite momentum transfers. Using a simple scattering function with double-Lorentzian shape, we demonstrate that this peak is a manifestation of simple diffusive spin fluctuations. Experimental results of several parameters are compared in the context of localized-moment and itinerant-electron pictures. The ratio of spin wave stiffness constant D and transition temperature kT/sub c/ is shown to be a good yardstick for the degree of itinerancy of d-electrons. 36 references.

A computer code (MIGRAT) is used to quantify the migration of moisture and multiple retarded contaminants in the unsaturated zone and assess the impact of open mine disposal of uranium mill tailings. The model is applied to a generic uranium mill tailings. The model is applied to a generic uranium mill tailings pit constructed with a clay-lined bottom and steep unlined sidewalls. The migration of a two contaminant system is modeled assuming that neither contaminant decays and only one contaminant is retarded. This study shows the anticipated result that the major pathway from the pit to the underlying water table is through the sidewall and that the time scales for this pathway are much shorter than those associated with the clay liner. More importantly, this study reveals that due to the strong nonlinear character of the hydraulic properties of unsaturated soils, concentrations of the retarded contaminant may only slightly lag the nonretarded contaminant through this pathway and contamination of the uppermost aquifer by the retarded contaminant may occur shortly after contamination by the nonretarded contaminant. 2 references, 5 figures.

Studies of the oxidation and gasification of oil shale char were extended to an investigation of the effects of mineral catalysis. Six shales with differing mineral compositions were studied, including samples from the saline zone in the Western Colorado and from the Antrim shales of Michigan. Oxidation kinetics data, corrected for mass transfer effects, were compared for all six samples. A high assay shale from Utah and a sample from the saline zone were found to have the highest oxidation rates. By examining the data for shales which were water leached and thermally pretreated, it was concluded that both NaO and CaO act as oxidation catalysts. However, as a result of mineral decomposition experiments conducted with a sample from the C-a lease tract, it appears as though the ankeritic dolomite fraction will not decompose as long as there is a minimal CO/sub 2/ over pressure. Rather, low temperature silication reactions appear to take place once the temperature exceeds 925/sup 0/K. An extensive evaluation was also completed for the gasification of an Antrim shale from Michigan. Both the rates of CO/sub 2/ and steam gasification of the char were found to be markedly lower than that observed for a shale sample …

Recently, there has been considerable interest in the central rapidity region of highly relativistic heavy-ion collisions. Such an interest stems from the possibility of creating hadron matter of high energy density which may exceed the critical energy density for a phase transition between ordinary confined matter and the unconfined quark-gluon plasma. The experimental searches and identification of the quark-gluon plasma may provide a new insight into the question of quark confinement. The estimate of the initial energy density is quite uncertain. The initial energy density is nonetheless an important physical quantity. It is one of the factors which determines whether the produced matter can undergo phase transition or not. The energy density has been estimated previously by using the color neutralization model of Brodsky et al. However, the color neutralization model gives a central rapidity multiplicity in heavy-ion collision too low by a factor of two. For this reason, we wish to obtain a better estimate of the energy density (in the central rapidity region). As is well known, a simple Glauber-type multiple collision model can reproduce the total multiplicity and multiplicity plateau near the central rapidity region to within 30%. The simple multiple collision model has an approximate validity …

The exchange badge system which was used at the Plutonium Facility located in Technical Area 55 was replaced on a trial basis with an automated Entry Control System. As a result of the success of the trial system, a new system incorporating expanded features and increased reliability is being implemented. The new Entry Control System incorporates several features not previously available in relatively inexpensive entry systems. The reliability of the system is enhanced by redundant microprocessors incorporating bubble memory for nonvolatile storage of the system data base. The badge readers incorporate dual communication lines to two different controllers to further increase the total system reliability.

Corrosion and erosion/corrosion testing of gas turbine materials in the effluent from a pressurized fluidized bed coal combustor continues under the Long Term Materials Test program. Two 1000-hour erosion/corrosion screening tests of twelve candidate gas turbine vane and blade base alloys and a variety of protective coating systems have been completed. Test conditions included 1350/sup 0/F, 800 to 900 ft/s and particulate loadings of 30 to 90 ppM. Erosion/corrosion degradation rates of 1 to 4 mils/1000 hours were observed with corrosion predominant in areas of particle impaction. FeCrAlY, CoCrAlY and rhodium aluminide coatings show significantly better resistance to degradation than unprotected base alloys, aluminide or platinum-aluminide diffusion coatings.

Stimulated Raman scattering of an XeCl laser at 308 nm in a high pressure H/sub 2/ cell shows anomalously high conversion into first Stokes (S1) when a pumping geometry with a Fresnel number near unity is used. Specifically a quantum efficiency of 88% is obtained into S1. Comparison with a plane-wave model indicates that a theory including diffraction and 4-wave mixing may be necessary to understand the anomalous holdoff of the second Stokes component. 10 references.

We consider a zero-..beta.. spheromak contained in a rectangular region having perfectly conducting boundaries in its minimum energy state, and we calculate its evolution. Our results may be summarized as follows. Since this state is a stable equilibrium, the initial evolution of the plasma is caused by diffusion. We simulate this using a transport code. We find that q at the magnetic axis drops and q(r) becomes flat. When q on axis drops below 0.5, the spheromak becomes unstable to an n = 2 kink. The plasma is then modeled dynamically; the kink displacement saturates and eventually reverses when a reconnection occurs. A new magnetic axis begins to form as the plasma relaxes toward a minimum energy state.

A computer-controlled multichannel analysis system has been developed by the Radiological Survey Activities Group at Oak Ridge National Laboratory (ORNL) for the Department of Energy (DOE) in support of the DOE's remedial action programs. The purpose of this system is to provide a rapid estimate of the /sup 226/Ra concentration in soil samples using a 6 x 9-in. NaI(Tl) crystal containing a 3.25-in. deep by 3.5-in. diameter well. This gamma detection system is controlled by a mini-computer with a dual floppy disk storage medium. A two-chip interface was also designed at ORNL which handles all control signals generated from the computer keyboard. These computer-generated control signals are processed in machine language for rapid data transfer and BASIC language is used for data processing.

The Mirror Fusion Test Facility is a major magnetic fusion energy project at the Lawrence Livermore National Laboratory. An important component of this facility is the vacuum vessel, which forms the vacuum chamber. The vessel is supported on twenty-two pairs of legs that rest on reinforced concrete piers. In performing static and dynamic analyses on the vacuum vessel, we separately investigated the load distribution under gravity loads, pressure loads, electromagnetic loads, and thermal loads. We also performed sophisticated dynamic analyses to predict the structural behavior under a postulated earthquake. The modeling assumptions and analytic procedures are highlighted in this paper.

The calibration factor for albedo neutron dosimeters varies greatly depending upon the energy of the neutrons in the exposure. Calibration results obtained over an eight-year period at each Lawrence Livermore National Laboratory facility where neutron exposure may occur were reviewed. A stronger relationship than expected was found between the ratio of the readings of the 9-in. to 3-in. spheres and the percent thermal. Readings from personnel and albedo badges were reviewed. The readings were consistent with the use of a calibration factor for the albedo dosimeter which varies with changes in the ratio of the personnel and albedo dosimeter TLD readings. 2 references, 6 figures. (ACR)

Some recent transport studies of field-reversed configurations (FRC) during their equilibrium phase are presented. The FRC confinement times of interest tau/sub N/, tau/sub E/, and tau/ sub phi/ are for particles, energy, and trapped-flux, respectively. An analytical expression for tau/sub N/ based on Lower-Hybrid-Drift (LHD) resistivity is presented. Some progress in assessing the respective contributions of radiation and thermal conduction to tau/sub E/ is given. Finally, the relation tau/sub E/ less than or equal to tau/sub phi/ is discussed.

The voltammetric characteristics of Pt(II) and Pt(IV) have been examined at a vitreous carbon electrode in slightly acidic 3M (approx. 15 wt %) NaCl solutions. Pt(IV) is reduced to Pt(II) at approx. 0 V and Pt(II) is reduced to Pt(0) at approx. -0.5 V vs Ag-AgCl. The rate of deposition of platinum metal at -0.5 V is very low on bare carbon, but increases as the coverage of platinum increases. The potential at which hydrogen is evolved in this medium is approx. -0.85 V. A technique has been tested for the removal of sub-part-per-million levels of platinum from the high-salinity brine by controlled-potential electrolysis using a reticulated, vitreous-carbon, flow-through electrode. However, at control potentials negative enough to begin to electrodeposit the platinum at a significant rate, simultaneous reduction of hydrogen ion reduces the current and energy efficiency to an unacceptable level.

The electromagnetics of one of several techniques for generating FRCs in a coaxial configuration has been presented. It has been shown that the discussed design satisfies all the electromagnetic requirements for a slow source. The next major issue is the investigation of the plasma physics which will ultimately determine the viability of this concept.

An expression to predict the onset of growth of a crack in a quasibrittle material is derived. An energy criterion essentially equivalent to the first two laws of thermodynamics is employed. The criterion is applied to the elastic-plastic crack of Olesiak and Wnuk (1968). 12 references, 3 figures. (ACR)

This is a design document for the Timing and Control Monitor System Upgrade Project. This project is intended to provide a replacement system for the existing user Encoder Monitor Systems and Varian 72 Control Room computer systems. All of these systems reside at the Nevada Test Site. The function of the T and C Monitor System is to gather real-time statistics and data on user defined key variables from control, communication, data acquistion systems, and from the monitoring system itself. The control, communication, and data acquisition systems each operate separately from the monitor system. The T and C Monitor System gathers this data in order to verify the readiness of an event to begin countdown. This includes setup, verification, calibration, and peripheral services, report any failures that may occur during the countdown, verify detonation and containment, and assist reentry activities after the event.