This report was prepared for the National Advisory Committee for Aeronautics and presents the results of investigations conducted by the Forest Products Laboratory of the United States Forest Service on the manufacture, preparation, application, testing and physical properties of the different types of glues used in wood airplane parts.

In this report are described four different types of propellers which appeared at widely separated dates, but which were exhibited together at the last Salon de l'Aeronautique. The four propellers are the Chaviere variable pitch propeller, the variable pitch propeller used on the Clement Bayard dirigible, the variable pitch propeller used on Italian dirigibles, and the Levasseur variable pitch propeller.

This report deals with an extension of the theory of stability in oscillation to the case of aircraft following a vertical trajectory, and particularly to the oscillations of parachutes.

The construction of giant airplanes was begun in Germany in August, 1914. The tables annexed here show that a large number of airplanes weighing up to 15.5 tons were constructed and tested in Germany during the War, and it is certain that no other country turned out airplanes of this weight nor in such large numbers. An examination of the tables shows that by the end of the War all the manufacturers had arrived at a well-defined type, namely an airplane of about 12 tons with four engines of 260 horsepower each. The aircraft listed here are discussed with regard to useful weight and aerodynamic qualities.

Report discusses the theory of inflow of the propeller and the fact that both suctional axial velocity and suctional tangential velocity must be considered when calculating the maximum efficiency.

This report is an analysis of the maximum flight radii of typical large airplanes and a discussion of the way in which the possible length of flight is affected by the change of weight by consumption of fuel during the flight.

"In terminating the study of the adaptation of the engine to the airplane, we will examine the problem of the turbo-compressor, the first realization of which dates from the war; this will form an addition to the indications already given on supercharging at various altitudes. This subject is of great importance for the application of the turbo-compressor worked by the exhaust gases. Assuming that the increase of pressure in the admission manifold is the same in both cases, the pressure in the exhaust manifold would be greater in the case in which the compressor is worked by the exhaust gas and there would result a certain reduction of engine power which we must be able to calculate" (p. 1).

Report presents descriptions, schematics, and photographs of the altitude laboratory for the testing of aircraft engines constructed at the Bureau of Standards for the National Advisory Committee for Aeronautics.

Extensive series of experiments have been conducted at the Bureau of Standards to determine the properties of cooling radiator cores manufactured for airplanes and to develop improvements in design. The analysis of the problem on which this work was based, and consequently the experimental method employed, is different from that commonly used. Instead of attempting to test complete radiators, either full size or in model, uniform sections representing different types of core construction have been tested and an analysis of the results made with a view to determining independently the various factors which influence its performance. This report describes referenced method of analysis in predicting the performance of radiators designed for aeronautic use.

Among the fuels which will operate at compression ratios up to at least 8.0 without preignition or "pinking" is hecter fuel, whence a careful determination of its performance is of importance. For the test data presented in this report the hecter fuel used was a mixture of 30 per cent benzol and 70 per cent cyclohexane, having a low freezing point, and distilling from first drop to 90 per cent at nearly a constant temperature, about 20 degrees c. below the average distillation temperature ("mean volatility") of the x gasoline (export grade). The results of these experiments show that the power developed by hecter fuel is the same as that developed by export aviation gasoline at about 1,800 r.p.m. at all altitudes. At lower speeds differences in the power developed by the fuels become evident. Comparisons at ground level were omitted to avoid any possibility of damaging the engine by operating with open throttle on gasoline at so high a compression. The fuel consumption per unit power based on weight, not volume, averaged more than 10 per cent greater with hecter than with x gasoline. The thermal efficiency of the engine when using hecter is less than when using gasoline, …

Part 1 is to present the results of tests on 56 types of core in a form convenient for use in the study of the performance of and possible improvements in existing designs. Working rules are given by which the data contained in the report may be used, and the most obvious conclusions as to the behavior of cores are summarized. Part 2 presents the results of tests made to determine the pressure necessary to produce water flows up to 50 gallons per minute through an 8-inch square section of radiator core. These data are of special value in evaluating the hydraulic head against which the circulating pump is required to operate.

Report presents the summation of results obtained in the testing of fuels of various compositions and characteristics in the altitude laboratory. The data upon which this report is based has had an important influence upon the writing of specifications for the various grades of aviation fuels.

Report outlines specifications for the preparation and application of self-luminous materials to be used for the illumination of various instruments, especially those used for aeronautics.

Report presents the results of wind tunnel tests of propellers that examined the influence of the following characteristics: (1) nominal pitch ratio 1.3 combined with a certain number of the more common or standard forms and proportions; (2) driving face slightly rounded or convex; (3) change in the location of the maximum thickness ordinate of the blade section; (4) pushing forward the leading edge of the blade, thus giving a rounded convex surface on the leading side of the driving face. (5) a series of values for the constant "angle of attack" in forming propellers with radially increasing pitch. In accordance with these purposes tests were carried out on 28 propellers.

Report describes a simple, portable apparatus for testing hydrogen, with special reference to its use in balloons. "In the generation, storage, and use of hydrogen for balloon purposes it is necessary to be able to determine, first, its lifting power, and, secondly, its purity. The lifting power may be determined directly from the specific gravity. Contamination by other gases may be determined by analysis for oxygen, carbon dioxide, etc., by the usual methods of gas analysis" (p. 469).

Report describes methods and materials used in waterproofing and fireproofing airplane fabrics using dopes. The determination of the probable life of a balloon fabric in service by experimental means is of great value in choosing the most suitable fabrics for a given purpose and in pointing the way to improvements in compounding and construction. The usefulness of exposure to the weather for this purpose has been amply demonstrated.

The author examines the current theory on the importance of reducing slip in airplane propellers. The author feels an exaggerated importance is attached to this supposition and feels that the increase in friction by an increase in propeller area or number of revolutions can't be discounted.

This report is a study of the results obtained from a large number of test of an Hispano-Suiza airplane engine in the altitude laboratory of the Bureau of Standards. It was originally undertaken to determine the heat distribution in such an engine, but many other factors are also considered as bearing on this matter.

This report presents the results of an investigation into the utility, action, and design of the auxiliary spark gap as a means for insuring freedom from spark plug failure due to fouling, and also to enable the restarting of fouled plugs. A brief account is given of the use of this gap up to the present time and also of the statements concerning it which have gained some currency, most of which are shown to be erroneous. The simple theory of the action of the series gap is discussed and a detailed account given of the effect upon the sparking ability of the plug produced by changes in the values of the electrical resistance of the fouling and of the capacities in parallel with the plug and with the magneto or coil.

"If we wish to form an accurate idea of the extraordinary progress achieved in aeronautics, a comparison must be made of the latest altitude records and the figures regarded as highest attainable limit some ten years ago. It is desirable, for two reasons, that we should be able to define the limit of the altitudes that can be reached without artificial aid. First, to know to what extent the human body can endure the inhalation of rarified air. Second, the mental capacity of the aviator must be tested at high altitudes and the limit known below which he is able to make reliable observations without being artificially supplied with oxygen" (p. 1).

Report discusses information obtained from studying large birds that fly by soaring, which involves using the wind without moving their wings. An Egyptian vulture and African white-backed vulture were observed and their relative air speed, upward air velocity, lift, and drag were noted. The experimental methods for measuring these values are described.

As an airplane rises to high altitudes the decrease in the density and the temperature of the air have important effects on the performance of the radiator. This report gives the results of a study of the effect of reduced pressure and temperature upon the capacity of airplane radiators. A method is presented by which the performance of a radiator at an altitude may be estimated for a particular speed of the airplane at a particular altitude.

Report develops a fundamental conception and partial application of a method for calculating the pressure-volume relationships to be expected for any given engine design. It outlines a method of computing and interpreting low-pressure indicator cards.

Part 1 deals with the head resistance of a number of common types of radiator cores at different speeds in free air, as measured in the wind tunnel at the bureau of standards. Part 2 gives the results of wind tunnel tests of resistance on a model fuselage with a nose radiator. Part 3 presents the results of preliminary tests of head resistance of a radiator enclosed in a streamlined casing.