The reflectivity at normal incidence of copper and aluminum samples was recently measured over a large frequency range at Brookhaven by one of us (JT). Then using the Kramers-Kroning integrals, and assuming the free-electron model of conductivity, the dependence of conductivity on frequency was obtained. The results seemed to suggest, for example, that the dc conductivities of the copper and evaporated aluminum samples are a factor of 3 lower than expected. We propose in this report, instead, directly fitting the free-electron model to the low frequency end of the reflectivity data. This fitting does not depend on the higher frequency results and on Kramers-Kronig integrations, but it does assume that the data at the low frequency end is sufficiently accurate. Note that for our LCLS wakefield studies, it is only over these (relatively) low frequencies that we need to know the electrical properties of the metals. The equations that relate reflectivity R with the free electron parameters dc conductivity {sigma} and relaxation time {tau} are: (1) {tilde {sigma}} = {sigma}/1-ikc{tau}; (2) {tilde n} = {radical} {tilde {epsilon}} = {radical}(1+4{pi}i{tilde k}c/{omega}); and (3) R = |{tilde n}-1/{tilde n} + 1|{sup 2}. The parameters are ac conductivity {tilde {sigma}}, index of refraction …

Installations of solar photovoltaic (PV) systems have been growing at a rapid pace in recent years. In 2009, approximately 7,500 megawatts (MW) of PV were installed globally, up from approximately 6,000 MW in 2008, consisting primarily of grid-connected applications. With 335 MW of grid-connected PV capacity added in 2009, the United States was the world's fourth largest PV market in 2009, behind Germany, Italy, and Japan. The market for PV in the United States is driven by national, state, and local government incentives, including up-front cash rebates, production-based incentives, requirements that electricity suppliers purchase a certain amount of solar energy, and federal and state tax benefits. These programs are, in part, motivated by the popular appeal of solar energy, and by the positive attributes of PV - modest environmental impacts, avoidance of fuel price risks, coincidence with peak electrical demand, and the possible deployment of PV at the point of use. Given the relatively high cost of PV, however, a key goal of these policies is to encourage cost reductions over time. Therefore, as policy incentives have become more significant and as PV deployment has accelerated, so too has the desire to track the installed cost of PV systems over …

The decision to implement the Innovation in Nuclear Infrastructure and Engineering Program (INIE) was an important first step towards ensuring that the United States preserves its worldwide leadership role in the field of nuclear science and engineering. Prior to INIE, university nuclear science and engineering programs were waning, undergraduate student enrollment was down, university research reactors were being shut down, while others faced the real possibility of closure. For too long, cutting edge research in the areas of nuclear medicine, neutron scattering, radiochemistry, and advanced materials was undervalued and therefore underfunded. The INIE program corrected this lapse in focus and direction and started the process of drawing a new blueprint with positive goals and objectives that supports existing as well the next generation of educators, students and researchers.

Measurements of the earth's magnetic field at several locations at SLAC were conducted to determine the possible field error contribution from tuning the undulators in a location with a different magnetic field than that which will be found in the undulator hall. An average difference of 0.08 {+-} 0.04 Gauss has been measured between the downward earth's field components in the test facility and SLAC tunnel locations.

A triggering system for magnetic field measurements of the LCLS undulators has been built with a National Instruments PXI-1002 and a Xylinx FPGA board. The system generates single triggers at specified positions, regardless of encoder sensor jitter about a linear scale.

This report focuses on the United States' relationship with Iran and how the Obama Administration is handling prior administration's economic sanctions against Iran. The Obama Administration's policy approach toward Iran has contrasted with the Bush Administration's by attempting to couple the imposition of sanctions to an active and direct U.S. effort to negotiate with Iran on the nuclear issue. That approach was not initially altered because of the Iranian dispute over its June 12, 2009, elections. However, with subsequent negotiations yielding no firm Iranian agreement to compromise, since early 2010 the Administration has focused on achieving the imposition of additional U.N., U.S., and allied country sanctions whose cumulative effect would be to compel it to accept a nuclear bargain.

Fiducialization of the LCLS undulators will be based on magnetic measurements by Hall probe. Pointed magnets, proposed by I.Vasserman for quadrupole lens fiducialization will be used as an intermediate reference. A prototype of the pointed magnet fixture has been made and tested. In this note we will describe a procedure for measuring the position of the center of the Hall probe sensitive area with respect to the undulator fiducial marks. The pointed magnet calibration procedure, a two-point algorithm for locating the magnetic center of the fixture, and test results are presented.

Final dimensions for the LCLS RF gun are described. This gun, referred to as the LCLS gun, is a modified version of the UCLA/BNL/SLAC 1.6 cell S-Band RF gun [1], referred to as the prototype gun. The changes include a larger mode separation (15 MHz for the LCLS gun vs. 3.5 MHz for the prototype gun), a larger radius at the iris between the 2 cells, a reduced surface field on the curvature of the iris between the two cells, Z power coupling, increased cooling channels for operation at 120 Hz, dual rf feed, deformation tuning of the full cell, and field probes in both cells. Temporal shaping of the klystron pulse, to reduce the average power dissipated in the gun, has also been adopted. By increasing the mode separation, the amplitude of the 0-mode electric field on the cathode decreases from 10% of the peak on axis field for the prototype gun to less than 3% for the LCLS gun for the steady state fields. Beam performance is improved as shown by the PARMELA simulations. The gun should be designed to accept a future load lock system. Modifications follow the recommendations of our RF review committee [2]. Files and …

The main result of this note is that no wakefield mitigation is required for the Radiation Stopper (RST1) in the LCLS injector. The RST1 geometry is not symmetric in the vertical direction, and we derive a slight modification to the diffraction model wake for a cylindrically symmetric (2D) cavity that can be used for this problem. Performing a full 3D MAFIA calculation for the nominal 1 mm (rms) long bunch, we show that the modified diffraction model well describes the wakefields generated in RST1. The results imply an on-axis emittance growth of 0.0075%, well below the 0.5% tolerance threshold. To reach the 0.5% threshold the beam would need to be mis-steered by a large amount - 7 mm - from the axis. One reason that the effect is small is that the beta functions at the RST1 are small.

In this document, we report on basic wakefield computations used to establish the impedance budget for the LCLS injector. Systematic comparisons between analytic formulae and results from ABCI are done. Finally, a comparison between 2D and 3D wakefield calculations are given for a cross. The three parts of the document are presented as follows: (1) ABCI computations for a few structures (Flange, Bellows...); (2) Comparison analytic with ABCI runs; and (3) Comparison Cross and Cavity using MAFIA.

The memo describes the maximum credible beam the LCLS injector can produce and lose at various locations along the beamline. The estimation procedure is based upon three previous reports [1, 2, 3]. While specific numbers have been updated to accurately reflect the present design parameters, the conclusions are very similar to those given in Ref 1. The source of the maximum credible beam results from the explosive electron emission from the photocathode if the drive laser intensity exceeds the threshold for plasma production. In this event, the gun's RF field can extract a large number of electrons from this plasma which are accelerated out of the gun and into the beamline. This electron emission persists until it has depleted the gun of all its energy. Hence the number of electrons emitted per pulse is limited by the amount of stored RF energy in the gun. It needs to be emphasized that this type of emission is highly undesirable, as it causes permanent damage to the cathode.

This report first examines the historical development of the offense of piracy, as defined by Congress and codified in the United States Code. The focus then turns to how contemporary international agreements define piracy. Finally, the report highlights developments in two trials involving charges of piracy in the federal district court in Norfolk, VA, United States v. Said and United States v. Hasan, specifically focusing on how the courts interpreted the definition of piracy under 18 U.S.C. § 1651.

This report discusses the budget for the 2008 Farm Bill, and its reauthorization. Moreover, the report discusses the increasing level of demand for fiscal constraint and the current large budget deficits.

This report discusses the Summary of 911 Legislation and Policy, Funding and Grants and National Broadband Plan.

This report provides background information on terrorist attacks in Russia's North Caucasus that includes the formerly breakaway Chechnya and other ethnic-based regions--appeared to increase substantially in 2007-2009. The report discusses impact of the August 2008 Russia-Georgia conflict and the recent development in the Northern Caucasus.

Final Report for “Effect of Asymmetric Versus Symmetric Warming on Grassland Mesocosms”

This report discusses new legislation being considered by the 111th Congress to improve the safety and security of the U.S. pipeline network. H.R. 6008 would require pipeline operators to provide immediate telephonic notice of a pipeline release to federal emergency response officials and would increase civil penalties for pipeline safety violations. S. 3824 would increase the number of federal pipeline safety inspectors, would require automatic shutoff valves for natural gas pipelines, and would mandate internal inspections of transmission pipelines, among other provisions

The LINAC Coherent Light Source [LCLS] is a free electron laser, designed to produce high brilliant X-ray beams using Self Amplified Spontaneous Emission [SASE]. Due to the physics of SASE, the electron beam has to be held very precisely on the same trajectory as the X-ray light beam generated by the undulator magnets. To optimize the SASE output, trajectory deviations between both beams have to be minimized to a few micrometers along the entire undulator section and held stable over the time period between beam-based-alignment processes. Consequently, extremely high position stability of all magnets in the undulator section is required to operate the LCLS successfully. The knowledge of any magnet movement exceeding few micrometers during periods of several weeks is essential for efficient X-ray generation. A well known principle of monitoring transverse component positions along beam lines is the application of stretched wires, associated with suitable wire position sensors and electronics. The particular challenge at LCLS is the required wire system performance in conjunction with the length of the undulator section and the large number of monitors. Verification of system stability and resolution under real conditions is the primary goal of this test setup. A stretched wire test setup has …

Lawrence Livermore National Laboratory (LLNL) as part of its Department of Energy (DOE), Energy Efficiency and Renewable Energy (EERE), and Vehicle Technologies Program (VTP) effort has investigated class 8 tractor-trailer aerodynamics for many years. This effort has identified many drag producing flow structures around the heavy vehicles and also has designed and tested many new active and passive drag reduction techniques and concepts for significant on the road fuel economy improvements. As part of this effort a database of experimental, computational, and conceptual design for aerodynamic drag reduction devices has been established. The objective of this report is to provide design guidance for trailer base devices to improve their aerodynamic performance. These devices are commonly referred to as boattails, base flaps, tail devices, and etc. The information provided here is based on past research and our most recent full-scale experimental investigations in collaboration with Navistar Inc. Additional supporting data from LLNL/Navistar wind tunnel, track test, and on the road test will be published soon. The trailer base devices can be identified by 4 flat panels that are attached to the rear edges of the trailer base to form a closed cavity. These devices have been engineered in many different forms …

None

This report provides a primer on the federal crop insurance program and discusses related issues.

This report discusses Congressional considerations regarding how to balance the federal government's growing need for sensitive or confidential business information, the public's right of access to information about government activities, and the private sector's interest in keeping its sensitive or proprietary information protected from public disclosure. The report discusses this issue in light of particularly the Freedom of Information Act (FOIA) and other similar legislation.

Several key LCLS undulator parameter values depend strongly on temperature primarily because of the permanent magnet material the undulators are constructed with. The undulators will be tuned to have specific parameter values in the Magnetic Measurement Facility (MMF). Consequently, it is necessary for the temperature of the MMF to remain fairly constant. Requirements on undulator temperature have been established. When in use, the undulator temperature will be in the range 20.0 {+-} 0.2 C. In the MMF, the undulator tuning will be done at 20.0 {+-} 0.1 C. For special studies, the MMF temperature set point can be changed to a value between 18 C and 23 C with stability of {+-}0.1 C. In order to ensure that the MMF temperature requirements are met, the MMF must have a system to measure temperatures. The accuracy of the MMF temperature measurement system must be better than the {+-}0.1 C undulator tuning temperature tolerance, and is taken to be {+-}0.01 C. The temperature measurement system for the MMF is under construction. It is similar to a prototype system we built two years ago in the Sector 10 alignment lab at SLAC. At that time, our goal was to measure the lab temperature …

A vibrating wire system is being developed to fiducialize the quadrupoles between undulator segments in the LCLS. This note provides a detailed analysis of the system. The LCLS will have quadrupoles between the undulator segments to keep the electron beam focused. If the quadrupoles are not centered on the beam axis, the beam will receive transverse kicks, causing it to deviate from the undulator axis. Beam based alignment will be used to move the quadrupoles onto a straight line, but an initial, conventional alignment must place the quadrupole centers on a straight line to 100 {micro}m. In the fiducialization step of the initial alignment, the position of the center of the quadrupole is measured relative to tooling balls on the outside of the quadrupole. The alignment crews then use the tooling balls to place the magnet in the tunnel. The required error on the location of the quadrupole center relative to the tooling balls must be less than 25 {micro}m. In this note, we analyze a system under construction for the quadrupole fiducialization. The system uses the vibrating wire technique to position a wire onto the quadrupole magnetic axis. The wire position is then related to tooling balls using wire …