A statistical design and analysis of both elemental analyses and weight percent solids analyses data was utilized to evaluate the MFT homogeneity at low heel levels and low agitator speed at both high and low solids feed concentrations. The homogeneity was also evaluated at both low and high agitator speed at the 6000+ gallons static level. The dynamic level portion of the test simulated feeding the Melter from the MFT to evaluate the uniformity of the solids slurry composition (Frit-PHA-Sludge) entering the melter from the MFT. This final report provides the results and conclusions from the second half of the study, the low weight percent solids concentration portion, as well as a comparison with the results from the first half of the study, the high weight percent solids portion.

A new reagent, BO-IMI, has been developed that achieves, single step, phosphate specific fluorescence labeling under aqueous conditions. Both 3 in. and 5 in. mononucleotides, including representative DNA adducts can be labeled. Included in this technique is a convenient procedure for postlabeling sample cleanup, leading to a practical detection of the products by capillary electrophoresis with laser fluorescencedetection. We consider that this new method will have a significant impact on the measurement of DNA adducts in human samples. This work was largely accomplished in the second half of our project. In the first half, we set up a new way to isolate DNA nucleotides from blood, worked with an initial, less specific technique for labeling DNA adducts, compared ionizing radiation vs oxidative damage to fluorescein labeled deoxyadenylic acid, and set up a capillary electrophoresis laser fluorescence detection system.

A new reagent, BO-IMI, has been developed that achieves, single step, phosphate specific fluorescence labeling under aqueous conditions. Both 3 in. and 5 in. mononucleotides, including representative DNA adducts can be labeled. Included in this technique is a convenient procedure for postlabeling sample cleanup, leading to a practical detection of the products by capillary electrophoresis with laser fluorescencedetection. We consider that this new method will have a significant impact on the measurement of DNA adducts in human samples. This work was largely accomplished in the second half of our project. In the first half, we set up a new way to isolate DNA nucleotides from blood, worked with an initial, less specific technique for labeling DNA adducts, compared ionizing radiation vs oxidative damage to fluorescein labeled deoxyadenylic acid, and set up a capillary electrophoresis laser fluorescence detection system.

None

We report improvement of the polarization diagnostics and their use in the development of the Optically Pumped Polarized Ion Source (OPPIS).

We report improvement of the polarization diagnostics and their use in the development of the Optically Pumped Polarized Ion Source (OPPIS).

Experiments have been developed for measuring the rates of chemical reactions liquids and in supercritical Co[sub 2]. A pulsed (Q-switch) Nd:YAG laser at 355 nm was the pump beam for laser flash photolysis studies of molybdenum and tungsten hexacarbonyls undergoing ligand displacement reactions by bidentate chelating agents such as 2,2[prime]-bipyridine in toluene. Experiments were carried out at 0.1 to 150 MPa. In the case of molybdenum complexes, the reaction mechanism for thermal ring closure is found from activation volumes to change from associative interchange to dissociative interchange as substituents on the 2,2[prime]-bipyridine ligands become bulkier. In a similar study of more rigid, substituted phenanthroline bidentate ligands it was found that substituent bulkiness had little effect on the thermal ring closure mechanism. Similar high pressure flash photolysis experiments with tungsten hexacarbonyl have also been completed. The concentration dependence of the fluorescence and nonradiative decay quantum yields for cresyl violet in several solvent have been reported as well as stability constants for the complexation of lithium ion by four different crown ethers dissolved in a room temperature molten salt.

Experiments have been developed for measuring the rates of chemical reactions liquids and in supercritical Co{sub 2}. A pulsed (Q-switch) Nd:YAG laser at 355 nm was the pump beam for laser flash photolysis studies of molybdenum and tungsten hexacarbonyls undergoing ligand displacement reactions by bidentate chelating agents such as 2,2{prime}-bipyridine in toluene. Experiments were carried out at 0.1 to 150 MPa. In the case of molybdenum complexes, the reaction mechanism for thermal ring closure is found from activation volumes to change from associative interchange to dissociative interchange as substituents on the 2,2{prime}-bipyridine ligands become bulkier. In a similar study of more rigid, substituted phenanthroline bidentate ligands it was found that substituent bulkiness had little effect on the thermal ring closure mechanism. Similar high pressure flash photolysis experiments with tungsten hexacarbonyl have also been completed. The concentration dependence of the fluorescence and nonradiative decay quantum yields for cresyl violet in several solvent have been reported as well as stability constants for the complexation of lithium ion by four different crown ethers dissolved in a room temperature molten salt.

This report presents results of an assessment of the available information concerning US Environmental Protection Agency (EPA) quality assurance/quality control (QA/QC) requirements and guidance applicable to sampling, handling, and analyzing physical parameter samples at Comprehensive Environmental Restoration, Compensation, and Liability Act (CERCLA) investigation sites. Geotechnical testing laboratories measure the following physical properties of soil and sediment samples collected during CERCLA remedial investigations (RI) at the Hanford Site: moisture content, grain size by sieve, grain size by hydrometer, specific gravity, bulk density/porosity, saturated hydraulic conductivity, moisture retention, unsaturated hydraulic conductivity, and permeability of rocks by flowing air. Geotechnical testing laboratories also measure the following chemical parameters of soil and sediment samples collected during Hanford Site CERCLA RI: calcium carbonate and saturated column leach testing. Physical parameter data are used for (1) characterization of vadose and saturated zone geology and hydrogeology, (2) selection of monitoring well screen sizes, (3) to support modeling and analysis of the vadose and saturated zones, and (4) for engineering design. The objectives of this report are to determine the QA/QC levels accepted in the EPA Region 10 for the sampling, handling, and analysis of soil samples for physical parameters during CERCLA RI.

During 1992, the radioactive effluents in the Savannah River were less than those observed in 1991. Vogtle reported no significant releases in 1992, and in earlier years Vogtle improvements in pre-processing their releases had already effected a decreasing trend in release levels. Their effluents continue to be dominated by {sup 58}Co, which had a maximum concentration of only 0.068 pCi/L, which is just 1/3 of the maximum observed in 1991. Many of the other man-made radionuclides observed in earlier years have now decreased to where some are not even detected, and no new radionuclides were detected in the 1992 Vogtle effluents. In addition to {sup 58}Co, low levels of {sup 60}Co were frequently observed, but only traces of {sup 54}Mn and {sup 95}Nb were observed. Contrary to earlier years no {sup 51}Cr, {sup 57}Co, {sup 59}Fe, or {sup 95}Zr were seen in 1992. Tritium and {sup 137}Cs were also monitored, but their levels generally remain consistent with known SRS sources. The maximum tritium observed near Vogtle was 2 pCi,/mL. The maximum downstream tritium was higher (3.8 pCi/mL), primarily due to the tritium release from K-Reactor in December 1991; however, the levels had abated significantly prior to collection of the tritium …

We have recently completed a two-year study of recirculating induction heavy-ion accelerators (recirculators) as low-cost drivers for inertial-fusion-energy power plants. We present here a summary of that study and other recent work on recirculators.

None

Laser induced damage to optical coatings is generally a localized phenomenon associated with coating defects. The most common of the defect types are the well-known nodule defect. This paper reviews the use of experiments and modeling to understand the formation of these defects and their interaction with laser light. Of particular interest are efforts to identify which defects are most susceptible to laser damage. Also discussed are possible methods for stabilizing these defects (laser conditioning) or preventing their initiation (source stabilization, spatter particle trapping).

The project described in this Report was to investigate the possibility of using sorbent added to coal-water fuel (CWF) mixtures as a means of reducing SOX emissions when burning Ohio coal. The results are significantly encouraging, with SOX concentrations reduced by amounts ranging from 25% to 65%, depending on the sorbent type and the firing conditions, where one major condition identified was the residence time in the flame gases. With the sorbent-loaded slurrys, the trend generally showed increasing SO{sub 2} capture with increasing sorbent loading. There were significant differences between the two different mixture formulations, however: The calcite/No. 8-seam mixture showed significantly higher SO{sub 2} capture at all times (ranging from 45% to 65%) than did the dolomite/No. 5 seam mixture (ranging from 25% to 45%). If the successes so far achieved are not to be wasted, advantage should be taken of these encouraging results by extending the work at both the present scale to determine the other unknown factors controlling sorption efficiency, and at larger scale to start implementation in commercial systems.

An investigation into the preparation of sol-gel coatings for high power lasers was started at LLNL in 1983 and AR coatings were successfully developed for use in the Nova laser in 1984. Several other large lasers now use these coatings. Subsequent work on HR coatings resulted in AlOOH/SiO{sub 2} and later ZrO{sub 2} or HfO{sub 2}/SiO{sub 2} systems of good optical performance. The use of organic polymer binders gave increased damage threshold and enhanced optical performance. We are in the process of scaling up HR fabrication for substrates approximately 38 cm square. Concurrently we are developing sol-gel random phase plates for laser beam smoothing. These have a patterned surface design of silica which induces phase shifts in the beam by variation in the optical path length. Plates of this type on 80 cm diameter substrates have been used successfully on the Nova.

The Pennsylvania State University is conducting a superclean coal-water slurry (SCCWS) program for the United States Department of Energy (DOE) and the Commonwealth of Pennsylvania with the objective of determining the capability of effectively firing SCCWS in an industrial boiler designed for heavy fuel oil. Penn State has entered into a cooperative agreement with DOE to determine if SCCWS (a fuel containing coal with 3.0 wt.% ash and 0.9 wt.% sulfur) can effectively be burned in a heavy fuel oil-designed industrial boiler without adverse impact on boiler rating, maintainability, reliability, and availability. The project will provide information on the design of new systems specifically configured to fire these clean coal-based fuels. The project consists of four phases: (1) design, permitting, and test planning, (2) construction and start up, (3) demonstration and evaluation (1,000-hour demonstration), and (4) program expansion (additional 1,000 hours of testing). The boiler testing wig determine if the SCCWS combustion characteristics, heat release rate, fouling and slagging behavior, corrosion and erosion limits, and fuel transport, storage, and handling characteristics can be accommodated in an oil-designed boiler system. In addition, the proof-of-concept demonstration will generate data to determine how the properties of SCCWS and its parent coal affect boiler …

The Pennsylvania State University is conducting a superclean coal-water slurry (SCCWS) program for the United States Department of Energy (DOE) and the Commonwealth of Pennsylvania with the objective of determining the capability of effectively firing SCCWS in an industrial boiler designed for heavy fuel oil. Penn State has entered into a cooperative agreement with DOE to determine if SCCWS (a fuel containing coal with 3.0 wt.% ash and 0.9 wt.% sulfur) can effectively be burned in a heavy fuel oil-designed industrial boiler without adverse impact on boiler rating, maintainability, reliability, and availability. The project will provide information on the design of new systems specifically configured to fire these clean coal-based fuels. The project consists of four phases: (1) design, permitting, and test planning, (2) construction and start up, (3) demonstration and evaluation (1,000-hour demonstration), and (4) program expansion (additional 1,000 hours of testing). The boiler testing wig determine if the SCCWS combustion characteristics, heat release rate, fouling and slagging behavior, corrosion and erosion limits, and fuel transport, storage, and handling characteristics can be accommodated in an oil-designed boiler system. In addition, the proof-of-concept demonstration will generate data to determine how the properties of SCCWS and its parent coal affect boiler …

In this paper the authors compare and contrast three powerful methods for experimentally measuring bond energies in polyatomic molecules. The methods are: radical kinetics; gas phase acidity cycles; and photoionization mass spectroscopy. The knowledge of the values of bond energies are a basic piece of information to a chemist. Chemical reactions involve the making and breaking of chemical bonds. It has been shown that comparable bonds in polyatomic molecules, compared to the same bonds in radicals, can be significantly different. These bond energies can be measured in terms of bond dissociation energies.

The empirical domain of validity of statistical theory is examined as applied to fission data on pre-fission data on pre-fission neutron, charged particle, and {gamma}-ray multiplicities. Systematics are found of the threshold excitation energy for the appearance of nonstatistical fission. From the data on systems with not too high fissility, the relevant phenomenological parameter is the ratio of the threshold temperature T{sub thresh} to the (temperature-dependent) fission barrier height E{sub Bar}(T). The statistical model reproduces the data for T{sub thresh}/E{sub Bar}(T) < 0.26 {plus_minus} 0.05, but underpredicts the multiplicities at higher T{sub thresh}/E{sub Bar}(T) independent of mass and fissility of the systems.

During the last quarter, work has focused on developing a numerical model to. approximate the flow characteristics of the Gladys McCall reservoir. Various reservoir models have been used in the study to simulate the well transient pressure and pressure derivative behavior during the reservoir production period. The pressure behavior of the 1983 Reservoir Limits Test (RLT) was closely matched by an elongated linear reservoir model with the well located off-center. The matching procedure appears to provide reasonable estimates of the probable configuration of Gladys McCall reservoir.geometry. Double-slope pressure behavior (on a semilog plot) develops after the. early radial flow period, indicating the existence of a no-flow boundary near the well. At later times, linear flow character (square-root-time straight line) becomes clear when two closer boundaries are both felt at the well.

During the last quarter, work has focused on developing a numerical model to. approximate the flow characteristics of the Gladys McCall reservoir. Various reservoir models have been used in the study to simulate the well transient pressure and pressure derivative behavior during the reservoir production period. The pressure behavior of the 1983 Reservoir Limits Test (RLT) was closely matched by an elongated linear reservoir model with the well located off-center. The matching procedure appears to provide reasonable estimates of the probable configuration of Gladys McCall reservoir.geometry. Double-slope pressure behavior (on a semilog plot) develops after the. early radial flow period, indicating the existence of a no-flow boundary near the well. At later times, linear flow character (square-root-time straight line) becomes clear when two closer boundaries are both felt at the well.

The scope of the Project is to develop and implement a ground water compliance strategy for all 24 UMTRA processing sites. The compliance strategy for the processing sites must satisfy requirements of the proposed EPA ground water cleanup standards in 40 CFR Part 192, Subparts B and C (1988). This scope of work will entail the following activities, on a site-specific basis: Development of a compliance strategy based upon modification of the UMTRA Surface Project remedial action plans (RAP) or development of Ground Water Project RAPs with NRC and state or tribal concurrence on the RAP; implementation of the RAP to include establishment of institutional controls, where appropriate; institution of long-term verification monitoring for transfer to a separate DOE program on or before the Project end date; and preparation of completion reports and final licensing on those sites that will be completed prior to the Project end date.

The Winter Fuels Report is intended to provide concise, timely information to the industry, the press, policymakers, consumers, analysts, and State and local governments on the following topics: Distillate fuel oil net production, imports and stocks on a US level and for all Petroleum Administration for Defense Districts (PADD) and product supplied on a US level; propane net production, imports and stocks on a US level and for PADD`s I, II, and III; natural gas supply and disposition and underground storage for the US and consumption for all PADD`S; as well as selected National average prices; residential and wholesale pricing data for heating oil and propane for those States participating in the joint Energy Information Administration (EIA)/State Heating Oil and Propane Program; crude oil and petroleum price comparisons for the US and selected cities; and a 6--10 Day, 30-Day, and 90-Day outlook for temperature and precipitation and US total heating degree-days by city.