In 1986, the US Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Project Office (WPO) (DOE-WPO) prepared a strategy for complying with the Environmental Protection Agency`s (EPA`s) Standards for the management of transuranic (TRU) waste. Section 3.2.2.2 of the DOE`s report addressed compliance with the Assurance Requirements found in 40 CFR {section} 191.14. One of the Assurance Requirements addresses the selection of repository sites that contain recoverable natural resources. This report documents that the site selection process for the WIPP facility did indeed comply with the natural resource disincentive requirement in 40 CFR {section} 191,14(e) at the time selected and therefore complies with the standard at this time. Thus, it shall be shown that it is reasonably certain that the WIPP site provides better overall protection than practical alternatives that were available when the site was selected. It is important to point out here, and it will be discussed later in the report, that the resource disincentive requirement is a preliminary siting criterion that requires further evaluation of sites that have resources (i.e, hydrocarbons, minerals and groundwater) in the vicinity or on the site. This further evaluation requires that for sites that do have resources, a qualitative determination must …

Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquefied petroleum gas, compressed natural gas, and electricity. Vehicle emission estimates included both exhaust and evaporative emissions for air pollutants of hydrocarbon, carbon monoxide, nitrogen oxides, and air-toxic pollutants of benzene, formaldehyde, 1,3-butadiene, and acetaldehyde. Vehicle life-cycle cost estimates accounted for vehicle purchase prices, vehicle life, fuel costs, and vehicle maintenance costs. Emission control cost-effectiveness presented in dollars per ton of emission reduction was calculated for each alternative-fuel vehicle types from the estimated vehicle life-cycle emission reductions and costs. Among various alternative-fuel vehicle types, compressed natural gas vehicles are the most cost-effective vehicle type in controlling vehicle emissions. Dedicated methanol vehicles are the next most cost-effective vehicle type. The cost-effectiveness of electric vehicles depends on improvements in electric vehicle battery technology. With low-cost, high-performance batteries, electric vehicles are more cost-effective than methanol, ethanol, and liquified petroleum gas vehicles.

The measurement of VOC concentrations in harsh chemical and physical environments is a formidable task. A surface acoustic wave (SAW) sensor has been designed for this purpose and its construction and testing are described in this paper. Included is a detailed description of the design elements specific to operation in 300{degree}C steam and HCl environments including temperature control, gas handling, and signal processing component descriptions. In addition, laboratory temperature stability was studied and a minimum detection limit was defined for operation in industrial environments. Finally, a description of field tests performed on steam reforming equipment at Synthetica Technologies Inc. of Richmond, CA is given including a report on destruction efficiency of CCl{sub 4} in the Synthetica moving bed evaporator. Design improvements based on the field tests are proposed.

The Lawrence Livermore National Laboratory was established in 1952 to do research on nuclear weapons and magnetic fusion energy. Since then other major programs have been added, including laser fusion and laser isotope separation, biomedical and environmental science, strategic defense, and applied energy technology. These programs require basic research in chemistry, materials science, computer science, engineering and physics. This bulletin is published on a monthly basis to report on unclassified work in all of the programs. There are two articles in this issue. Herbert F. York reminisces about the early days in Livermore, emphasizing the legacy of E.O. Lawrence, and comments on the role of the Laboratory in the future. COG, a new,high-resolution code for modeling radiation transport is described. The code is a new Monte Carlo neutron/photon transport code that solves complex radiation shielding and nuclear criticality problems. It is now available for high-speed desktop workstations as well as mainframes.

A discussion of the possible sources of discrepancies in the measurements of the quantum efficiency of CsI photocathodes is presented. We propose that the major causes for disagreements in QE are due to the QE dependence on the current density extracted from the photocathode, on the electric field, and on the temperature of the photocathode. Preliminary results on TMAE enhanced GaAs and Si, plus TMAE protected CsTe and SbCs photocathodes, operated in gas, are also presented.

A volatile organic compound (VOC) transport model has been developed to describe unsteady-state VOC permeation and diffusion within a waste drum. Model equations account for three primary mechanisms for VOC transport from a void volume within the drum. These mechanisms are VOC permeation across a polymer boundary, VOC diffusion across an opening in a volume boundary, and VOC solubilization in a polymer boundary. A series of lab-scale experiments was performed in which the VOC concentration was measured in simulated waste drums under different conditions. A lab-scale simulated waste drum consisted of a sized-down 55-gal metal drum containing a modified rigid polyethylene drum liner. Four polyethylene bags were sealed inside a large polyethylene bag, supported by a wire cage, and placed inside the drum liner. The small bags were filled with VOC-air gas mixture and the VOC concentration was measured throughout the drum over a period of time. Test variables included the type of VOC-air gas mixtures introduced into the small bags, the small bag closure type, and the presence or absence of a variable external heat source. Model results were calculated for those trials where the VOC permeability had been measured. Permeabilities for five VOCs [methylene chloride, 1,1,2-trichloro-1,2,2-trifluoroethane (Freon-113), 1,1,1-trichloroethane, …

The Department of Energy`s (DOE) Computerized Accident/Incident Reporting System (CAIRS) is a comprehensive data base containing more than 50,000 investigation reports of injury/illness, property damage and vehicle accident cases representing safety data from 1975 to the present for more than 150 DOE contractor organizations. A special feature is that the text of each accident report is translated using a controlled dictionary and rigid sentence structure called Factor Relationship and Sequence of Events (FRASE) that enhances the ability to retrieve specific types of information and to perform detailed analyses. DOE summary and individual contractor reports are prepared quarterly and annually. In addition, ``Safety Performance Profile`` reports for individual organizations are prepared to provide advance information to appraisal teams, and special topical reports are prepared for areas of concern such as an increase in the number of security injuries or environmental releases. The data base is open to all DOE and Contractor registered users with no access restrictions other than that required by the Privacy Act.

Insensitive high explosives (IHE`s) based on triamino-trinitrobenzene (TATB) have been demonstrated to be very insensitive to shock, thermal, friction and other stimuli. Hazard scenarios can involve more than one stimulus, such as heating followed by fragment impact (shock). The shock sensitivity of the IHE`s LX-17 and PBX-9502 preheated to a temperature (250{degree}C) just below thermal runaway is quantitatively studied using embedded manganin pressure gauges. The thermal expansion of TATB to 250{degree}C is measured to determine the state of the explosive prior to shock initiation. LX-17 and PBX-9502 are found to be significantly more sensitive at 250{degree}C than at lower temperatures, but still less sensitive than ambient temperature HMX-based explosives. An ignition and growth reactive flow computer model of the shock initiation of hot IHE is developed to allow predictions of the response of hot IHE to impact scenarios which can not be tested directly.

The purpose of this plan is to determine hydraulic conditions at Well 399-1-16C (16C) and to present a remediation plan. The objectives are to restore hydraulic isolation of the confined aquifer (water level returning to approximately 370 ft) and to prevent chemical contamination between the unconfined and confined aquifers. This work scope is an extension of Task 4d of the Remedial Investigation/Feasibility Study Work Plan for the 300-FF-5 Operable Unit, Hanford Site, Richland, Washington, DOE/RL 89-14 (1990), and is a result of discussions held with the regulators and documented this plan was presented to the regulators at the January 1993 unit managers meeting and is documented in the minutes from that meeting.

Thick (10 to 25 {mu}m), free-standing, equal layer thickness, Copper(Cu)-304 Stainless Steel(SS) multilayer foils, having periods of 1 to 100 nm, synthesized by magnetron sputter deposition, were examined by plan view and cross-sectional transmission electron microscopy. Multilayer growth morphology, individual layer structure and crystallographic phase orientation relationships were characterized in this study. Electron Energy Loss filtered imaging of a 20 nm period multilayer cross-section was also performed and showed that nickel had diffused into the Cu layers from the SS during synthesis. X-ray powder diffraction scans were performed and analyzed. A pure deposit of 304SS was synthesized and had a metastable BCC structure. Multilayer samples having periods of 20 nm were found to have a coherent layered Cu(FCC)SS(FCC) structure. At larger periods (50 & 100 nm) a bimodal Cu(FCC)-SS(FCC & BCC) structure was formed. These observations show that the 304SS will grow with a metastable BCC structure when sputter deposited. When layered with Cu(FCC) the 304SS has its equilibrium FCC structure at layer thicknesses up to 10nm as a result of epitaxy with the copper. At larger SS layer thicknesses the SS appears to locally transform to the metastable BCC structure during synthesis, refining the grain structure of the depositing …

Well UE-1-q is located in the northeastern portion of area 1 of the Nevada Test Site in southwestern Nevada, 1244.1 meters above sea level. The well was originally an exploratory hole drilled to a depth of 743 meters below the surface (mbs) by LANL in November of 1980. In May 1992, the Groundwater Characterization Program (GCP) extended the total depth to approximately 792.5 mbs. UE-1-q is cased to a total depth of 749.5 mbs, with the remaining uncased depth exposed exclusively to Paleozoicaged carbonate rock, the principle zone of groundwater sampling. Geologic logging indicates approximately 390 meters of tuffaceous and calcareous alluvium overlies 320 meters of Tertiary-aged volcanic ash-flow and bedded tuffs. Paleozoic carbonate lithology extends from 716 mbs to the total well depth and is separated from the overlying Tertiary volcanic deposits by 6 meters of paleocolluvium. This report outlines the results and interpretations of radiochemical and environmental isotopic analyses of groundwater sampled from UE-1-q on July 10, 1992 during the well pump test following well development. In addition, results of the field tritium monitoring performed during the well drilling are reported in Appendix 1. Sampling, analytical techniques, and analytical uncertainties for the groundwater analyses are presented in Appendix …

This is the final report for a subcontract to supply a Doppler Beam Sharpening model to interface with the radar stimulation package running on the Cray supercomputers. The article describes the beam sharpening model, and the way beam sharpening is implemented by the model. Changes from previous work are emphasized in this report.

Superplasticity in ceramics has now advanced to the stage that technologically viable superplastic deformation processing can be performed. In this paper, examples of biaxial gas-pressure forming of several ceramics are given. These include yttria stabilized, tetragonal zirconia (YTZP) a 20% alumina/YTZP composite, and silicon. In addition, the concurrent superplastic forming and diffusion bonding of a hybrid YTZP/C103 (ceramic-metal) structure are presented. These forming processes offer technological advantages of greater dimensional control and increased variety and complexity of shapes than is possible with conventional ceramic shaping technology.

Comprehensive neutronic evaluated data files for the naturally-occurring isotopes of cadmium are deduced from experimental data and nuclear models, and presented in the ENDF/B-VI formats. Particular attention is given to those processes relevant to fuel-cycle and fission-product applications. Comparisons are made with prior evaluations of the cadmium isotopes, and discrepancies and consistencies cited. Some of the discrepancies are very large 9.9 as much as 100%), and the differences have the potential for a pronounced impact on applications usage. The present files are comprehensive, including may important processes that are not represented in the contemporary ENDF/B-VI system. Recommendations are made for future measurements where appropriate.

During first quarter 1993, samples from 18 groundwater monitoring wells of the AMB series at the Metallurgical Laboratory Hazardous Waste Management Facility were analyzed for certain heavy metals, indicator parameters, radionuclides, volatile organic compounds, and other constituents. Nine parameters exceeded standards during the quarter. As in fourth quarter 1992, tetrachloroethylene and trichloroethylene exceeded the final Primary Drinking Water Standards in 4 and 7 wells, respectively. Dichloromethane (methylene chloride), not previously compared to a standard in the Savannah River Site Groundwater Monitoring Program, was elevated in one well. Aluminum, iron, manganese, pH, specific conductance, and total organic halogens exceeded the Savannah River Site Flag 2 criteria; all of these parameters, with the exception of aluminum, were reported as elevated in AMB wells during previous quarters. Groundwater flow directions and rates in the water-table unit and the upper section of the Congaree were similar to previous quarters.

This is the ``seventh`` and final Quarterly Report under the scope of work for cooperative agreement between the Western Interstate Energy Board and the US Department of Energy. The report covers the period January--March 1993. The cooperative agreement was to expire in June 1992, but DOE granted an extension through March 24, 1993. Since this is the last Quarterly Report under the expired cooperative agreement, most tasks are noted as being completed. Two final items, however, will soon be sent to DOE -- final minutes from the March 9--11 High- Level Radioactive Waste Committee meeting, and the Year-End Technical Report. Some highlights from the quarter: The Committee decided on a preferred format for the revised Spent Fuel and High-Level Radioactive Waste Transportation Primer. The document would be 100- 200 pages, accompanied by a series of white papers on key transportation elements. A 25--30 page handbook for educating western state elected officials would also be prepared. On March 24, the Committee sent a letter to DOE commenting on the Near-Site Transportation Infrastructure report findings. The Committee is concerned that infrastructure limitations may limit the rail shipping option in many instances, even after upgrades have been implemented. The NSTI findings may also …

Conventional hatcheries, supplementation, and habitat protection are management activities located on a production continuum. At one end of the continuum is the conventional hatchery which attempts to separate artificially propagated fish from naturally reproducing populations. On the other end of the continuum is natural production. Supplementation which attempts to increase natural production through the use of artificial propagation lies somewhere between natural production and conventional hatcheries on the continuum. The use of artificial propagation in the recovery of listed species is controversial. Guidance on the use of artificial propagation in the recovery of listed species comes from three sources: The Endangered Species Act (ESA), US Fish and Wildlife Service (USFWS) policies and National Marine Fisheries Service (NMFS) guidelines.

The stated purpose of the Endangered Species Act is to provide a means whereby the ecosystem upon which endangered species and threatened species depend may be conserved. Conservation of the Columbia River ecosystem and the diversity of gene pools, life histories, species, and communities that comprise it, should become a major objective of species recovery and fish and wildlife management programs in the Columbia River Basin. Biodiversity is important to both species and ecosystem health, and is a prerequisite to long-term sustainability of biological resources. In this paper, I provide an overview of various approaches to defining, measuring, monitoring, and protecting biodiversity. A holistic approach is stressed that simultaneously considers diverse species and resource management needs. Emphasis is on threatened and endangered species of salmon and their associated habitat.

This report consists of a detailed documentation of the writings and deliberations of the peer review panel that met on May 24--25, 1993 in Richland, Washington to evaluate your draft report ``Uncertainty/Sensitivity Analysis Plan`` (PNWD-2124 HEDR). The fact that uncertainties are being considered in temporally and spatially varying parameters through the use of alternative time histories and spatial patterns deserves special commendation. It is important to identify early those model components and parameters that will have the most influence on the magnitude and uncertainty of the dose estimates. These are the items that should be investigated most intensively prior to committing to a final set of results.

Talc-silicon glass-ceramic waste forms are being evaluated as candidates for immobilization of the high level calcined waste stored onsite at the Idaho Chemical Processing Plant. These glass-ceramic waste forms were prepared by hot isostatically pressing a mixture of simulated nonradioactive high level calcined waste, talc, silicon and aluminum metal additives. The waste forms were characterized for density, chemical durability, and glass and crystalline phase compositions. The results indicate improved density and chemical durability as the silicon content is increased.

The authors have found what appears to be a previously unreported error in the measurement of surface plate flatness and the measurement of angular displacement errors in rotary tables using angle interferometers.

During first quarter 1993, eight constituents exceeded final Primary Drinking Water Standards in groundwater samples from downgradient monitoring wells at the Mixed Waste anagement Facility, the Old Burial Ground, the E-Area Vaults, and the proposed Hazardous Waste/Mixed Waste Disposal Vaults (HWMWDV). As in previous quarters, tritium and trichloroethylene were the most widespread constituents. Tetrachloroethylene, chloroethene, 1,1-dichloroethylene, gross alpha, lead, or nonvolatile beta levels also exceeded standards in one or more wells. The elevated constituents were found primarily in Aquifer Zone IIB{sub 2} (Water Table) and Aquifer Zone IIB{sub 1}, (Barnwell/McBean) wells. However, several Aquifer Unit IIA (Congaree) wells also contained elevated constituent levels. The groundwater flow directions and rates in the three hydrostratigraphic units were similar to previous quarters.

On September 23, 1988, the US Environmental Protection Agency (EPA) published a notice clarifying interim status requirements for the management of radioactive mixed waste thereby subjecting the Idaho National Engineering Laboratory (INEL) and other applicable Department of Energy (DOE) sites to regulation under the Resource Conservation and Recovery Act (RCRA). Therefore, the DOE was required to submit a Part A Permit application for each treatment, storage, and disposal (TSD) unit within the INEL, defining the waste codes and processes to be regulated under RCRA. The September 1990 revised Part A Permit application, that was approved by the State of Idaho identified 101 potential acute and toxic hazardous waste codes (F-, P-, and U- listed wastes according to 40 CFR 261.31 and 40 CFR 261.33) for some TSD units at the Idaho Chemical Processing Plant. Most of these waste were assumed to have been introduced into the High-level Liquid Waste TSD units via laboratory drains connected to the Process Equipment Waste (PEW) evaporator (PEW system). At that time, a detailed and systematic evaluation of hazardous chemical use and disposal practices had not been conducted to determine if F-, P-, or Unlisted waste had been disposed to the PEW system. The purpose …

The raw gas environments that arise from coal gasification have chemical compositions that are low in pO{sub 2} and moderate-to-high in pS{sub 2}. Metallic materials for service in such an environment undergo predominantly sulfidation attack at temperatures of 400 to 700{degree}C. Modification of alloy compositions in bulk can alter the scaling processes and lead to improvements in corrosion resistance, but the benefits can only be attained at temperatures much higher than the service temperatures of the components. Modification of surfaces of structural components by several of the coating techniques examined in this study showed substantial benefit in corrosion resistance when tested in simulated coal gasification environments. The paper presents several examples of surface modification and their corrosion performance.