Structural design and analysis and other practical engineering considerations indicate that the 3-point, kinematic chamber support concept in the GEM Technical Design Report should be replaced by a 4-point, {open_quotes}partial{close_quotes} kinematic support design. Detector physics performance may increase due to a resulting decreased mass in the secondary support structure.

An electromagnetic accelerator in the form of a linear electric motor (LEM) has been designed to achieve controlled acceleration profiles of a carriage containing hydrodynamically unstable fluids for the investigation of the development of turbulent mix. The Rayleigh- Taylor instability is investigated by accelerating two dissimilar density fluids using the LEM to achieve a wide variety of acceleration and deceleration profiles. The acceleration profiles are achieved by independent control of rail and augmentation currents. A variety of acceleration-time profiles are possible including: (1) constant, (2) impulsive and (3) shaped. The LEM and support structure are a robust design in order to withstand high loads with deflections and to mitigate operational vibration. Vibration of the carriage during acceleration could create artifacts in the data which would interfere with the intended study of the Rayleigh-Taylor instability. The design allows clear access for diagnostic techniques such as laser induced fluorescence radiography, shadowgraphs and particle imaging velocimetry. Electromagnetic modeling codes were used to optimize the rail and augmentation coil positions within the support structure framework. Results of contemporary studies for non-arcing sliding contact of solid armatures are used for the design of the driving armature and the dynamic electromagnetic braking system. A 0. 6MJ …

In this study we present a new cloud treatment in an atmospheric climate model. The water (or ice) content of clouds is a introduced as a prognostic variable, subject to both advective and diffusive transport. In the first phase of the study, the cloud water does not affect the radiative properties of clouds. We then find differences in precipitation and cloud fields, but little effect on the overall climate. In the second phase the cloud water determines the reflectivity of the clouds. This causes large changes in the global circulation, largely due to enhanced reflection from high tropical cirrus clouds. As a third step, the cloud emissivity is also based on the cloud water content. This greatly enhances the outgoing terrestrial radiation and brings the model`s radiative budget quite close to the observed.

This topical report is the first for the UOP Bench-Scale Co-processing contract. The objective of this contract is to extend and optimize the UOP single-stage, slurry-catalyzed co-processing scheme. UOP co-processing uses a single-stage, slurry-catalyzed scheme in which petroleum vacuum resid and coal are simultaneously upgraded to a high-quality synthetic oil. A highly active, well-dispersed catalyst permits operations at moderate- and high-severity reaction conditions with minimum detrimental thermal reactions. In this process, finely ground coal, petroleum resid, and catalyst are mixed, combined with hydrogen, and then directed to a single-stage reactor, where the simultaneous upgrading of the petroleum resid and coal occurs. The reactor effluent is directed to a series of separators, where a hydrogen-rich gas is recovered and recycled back to the reactor inlet. The balance of the material is sent to a series of separators, where the light gasses, light oil, vacuum gas on (VGO), catalyst, unconverted coal, ash, and residues are recovered. The catalyst is recycled back to the reactor. The UOP co-processing scheme is designed to be integrated into a conventional petroleum refinery. the hydrocarbon products from the co-processing unit will be sent to the refinery for final upgrading to finished products. A major focus of this …

This is an OTA resource analysis report.

This Task Technical Plan summarizes work required to project the benzene emissions from the Late Wash Facility (LWF) as well as update the benzene, mercury, and NO{sub x} emissions from the remainder of the Defense Waste Processing Facility (DWPF). These calculations will reflect (1) the addition of the LWF and (2) the replacement of formic acid with nitric acid in the melter preparation process. The completed calculations will be used to assist DWPF in applying for the LWF Air Quality Permit.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Dan Morales, regarding a legal question submitted for clarification: Whether the University of Texas System is authorized to limit the number of vendors offering products to its faculty members under an optional retirement program governed by chapter 830 of the Government Code (RQ-612)

Use of ``LDS Moldable`` as a cushion material for future DWPF melters is deemed feasible, because it serves the purpose of reducing the stress in the steel shell to acceptable levels. The assessment is based on the design geometry of the DWPF melter currently undergoing testing.

The pyrolysis of methane in the absence of a quench was studied at temperatures between 900 and 1050{degrees}C and methane flows of 80--200 Scc/min. At 1050{degrees}C and a methane flow rate of 100 Scc/minute, methane conversion ranged between 15--19% with the major products being benzene, acetylene, and ethylene. The benzene molar selectivity was ca. 50%, corresponding to molar yield of ca. 7.5--10%. The reaction resulted in the formation of visible amounts of solid carbon, particularly at 1050{degrees}C. The resulting solid consisted partly of carbon and partly of a yellowish tar-like material which was soluble in toluene and contained various heavy hydrocarbons and polyring aromatics.

At the request of the former Secretary, an inspection of six classified intelligence and special access program work-for-others projects was conducted. The purpose of this inspection was to evaluate managements, effectiveness regarding these work-for-others projects and included tests for financial integrity and adherence to applicable laws and regulations. Details of the inspection are provided in this report.

KM, Knob Manager, is a tool which enables the user to use the SUNDIALS knob box to adjust the settings of the control system. The followings are some features of KM: dynamic knob assignments with the user friendly interface; user-defined gain for individual knob; graphical displays for operating range and status of each process variable is assigned; backup and restore one or multiple process variable; save current settings to a file and recall the settings from that file in future.

Effect of low-NO{sub x} firing. There was no clear-cut effect on the emission of trace metals or acid gases. The data give marginal evidence for a decreased emission of Cr(VI), which would be a favorable change but is not certain by any means. The effect on aldehydes and ketones cannot be stated because of the loss of samples for baseline conditions; no credible data on these compounds were obtained for baseline conditions. The change in volatile organics appeared to be a reduction in emissions, whereas that for semi-volatiles seemed to be an increase. Inasmuch as low-NO{sub x} firing is sometimes accompanied by large increases in the amount of unburned carbon in the ash, the result for semi-volatiles is more in line with expectation. Effect of the hot-side ESP. As indicated above, the hot-side ESP lowered trace-element emissions to the range roughly from 1 to 5% of the levels found in the inlet gas stream. Not surprisingly, the hot-side ESP had no measurable influence on the emissions of SO{sub x}, HF, and HCl. Quite surprisingly, on the other hand, the ESP seemed to suppress the emission of certain organic substances. Suppression of the emission of formaldehyde is particularly difficult to explain. …

The primary objectives of this task are to characterize the sludge, to identify any unexpected processing problems, and to demonstrate the ability to make an acceptable glass product. Another objective is to determine the amount of washing that the sludge from Tank 42 requires. The 500 ml glass Sludge Receipt and Adjustment Tank (SRAT) and the 100 L stainless steel SRAT have already been used in the Shielded Cells to demonstrate the process using samples from other tanks. The melter and off-gas system have also been used in the Shielded Cells to vitrify sludge from Tanks 8 & 12 and from Tank 51.

This procedure provides the operations approach, a field sampling plan, and laboratory procedures for a soil washing test to be conducted by Alternative Remedial Technologies, Inc. (ART) in the 300-FF-1 area at the Hanford site. The {open_quotes}Quality Assurance Project Plan for the Soil Washing Physical Separations Test, 300-FF-1 Operable Unit,{close_quotes} Hanford, Washington, Alternative Remedial Technologies, Inc., February 1994 (QAPP) is provided in a separate document that presents the procedural and organizational guidelines for this test. This document describes specifications, responsibilities, and general procedures to be followed to conduct physical separation soil treatability tests in the North Process Pond of the 300-FF-1 Operable Unit (OU) at the Hanford Site. These procedures are based on the {open_quotes}300-FF-1 Physical Separations CERCLA Treatability Test Plan, DOE/RL 92-2l,{close_quotes} (DOE-RL 1993).

This document supplements and extends the Functional Design Criteria, SP-W026-FDC-001, for the Waste Receiving and Processing Facility (WRAP), Module 1. It provides additional detailed requirements, summarizes key Westinghouse Hanford Company design guidance, and establishes baseline technical agreements to be used in definitive design of the WRAP-1 facility. Revision 3 of the Supplemental Design Requirements Document has been assigned an Impact Level of 3ESQ based on the content of the entire revision. The actual changes made from Revision 2 have an Impact Level of 3S and the basis for these changes was previously reviewed and approved per WHC correspondence No. 9355770.

Weekly newsletter discussing natural resources, parks, hunting and fishing, and other information related to the outdoors in Texas.

A weekly publication, the Texas Register serves as the journal of state agency rulemaking for Texas. Information published in the Texas Register includes proposed, adopted, withdrawn and emergency rule actions, notices of state agency review of agency rules, governor's appointments, attorney general opinions, and miscellaneous documents such as requests for proposals. After adoption, these rulemaking actions are codified into the Texas Administrative Code.

The largest source of uncertainty in the retrieval of SST (sea-surface) temperature from space-borne infrared radiometric measurements is in the correction for the effects of the intervening atmosphere. During a research cruise of the R/V Alliance measurements of sea surface temperature, surface meteorological variables and surface infrared radiances were taken. SST fields were generated from the ATSR data using pre-launch algorithims derived by the ATSR Instrument Team (A.M. Zavody, personal communication), and the initial comparison between ATSR measurements and SST taken along the ship`s track indicate that the dual-angle atmospheric correction is accurate in mid-latitude conditions.

Forty-four sediment samples were collected from 28 locations in the Hanford Reach of the Columbia River to assess the presence of metals and man-made radionuclides in the near shore and shoreline settings of the Hanford Site. Three locations were sampled upriver of the Hanford Site plutonium production reactors. Twenty-two locations were sampled near the reactors. Three locations were sampled downstream of the reactors near the Hanford Townsite. Sediment was collected from depths of 0 to 6 in. and between 12 to 24 in. below the surface. Samples containing concentrations of metals exceeding the 95 % upper threshold limit values (DOE-RL 1993b) are considered contaminated. Contamination by arsenic, chromium, copper, lead, and zinc was found. Man-made radionuclides occur in all samples except four collected opposite the Hanford Townsite. Man-made radionuclide concentrations were generally less than 1 pCi/g.

The present invention relates to highly corrosion resistant components for use in an electrochemical cell. Specifically, these components are resistant to corrosion under very extreme conditions such as exposure to aqua regia in the presence of a constant current density of 100mA/m{sup 2}. The components are comprised of an iridium-platinum alloy that comprises less than 30% iridium. In a preferred embodiment of the present invention, the iridium-platinum alloy comprises 15-20% iridium. In another preferred embodiment of the present invention, the iridium-platinum alloy is deposited on the surface of an electrochemical cell component by magnetron sputtering. The present invention also relates to a method for conducting an electrochemical reaction in the presence of highly corrosive acids under a high degree of polarization wherein the electrochemical cell comprises a component, preferably the anode, containing an iridium-platinum alloy that comprises less than 30% iridium.

The main goal of this contract is to develop a catalyst and technology that will produce iC{sub 4}= directly from coal-derived syngas and that is capable of utilizing a lower (0.5 to 1.0) H{sub 2}:CO ratio. The research will identify and optimize the key catalyst and process characteristics that give improved performance for CO conversion by a non-Fischer-Tropsch process. This report, which is the seventh quarterly report covers the testing of various ZrO{sub 2}-based catalyst systems designed to examine the effects of catalyst preparation and process variables, especially low calcination temperature and mild reaction conditions (low temperatures, low pressure and low space velocity). Testing of solvent-extracted sol-gel ZrO{sub 2} catalysts indicate a decrease in isobutene yield. Lowering the reaction temperature, pressure and space velocity resulted in a small improvement in isobutene yield. Three extended runs demonstrated reasonable catalyst stability. In view of the generally poor isobutene yields, the emphasis in this project will shift to isoalcohol production.

The objectives of this research project were to lay the foundation for further improvement in the use of geophysical methods for detection of buried wastes, and to increase the information content derived from surveys. Also, an important goal was to move from mere detection to characterization of buried wastes. The technical approach to achieve these objectives consisted of: (1) Collect a data set of high spatial density; (2) Acquire data with multiple sensors and integrate the interpretations inferred from the various sensors; (3) Test a simplified time domain electromagnetic system; and (4) Develop imaging and display formats of geophysical data readily understood by environmental scientists and engineers. The breadth of application of this work is far reaching. Not only are uncontrolled waste pits and trenches, abandoned underground storage tanks, and pipelines found throughout most US DOE facilities, but also at military installations and industrial facilities. Moreover, controlled land disposal sites may contain ``hot spots`` where drums and hazardous material may have been buried. The technologies addressed by the R&D will benefit all of these activities.

A nondestructive method, and associated apparatus, are provided for determining the grain flow of the grains in a convex curved, textured polycrystalline surface. The convex, curved surface of a polycrystalline article is aligned in a horizontal x-ray diffractometer and a monochromatic, converging x-ray beam is directed onto the curved surface of the polycrystalline article so that the converging x-ray beam is diffracted by crystallographic planes of the grains in the polycrystalline article. The diffracted x-ray beam is caused to pass through a set of horizontal, parallel slits to limit the height of the beam and thereafter. The linear intensity of the diffracted x-ray is measured, suing a linear position sensitive proportional counter, as a function of position in a direction orthogonal to the counter so as to generate two dimensional data. An image of the grains in the curved surface of the polycrystalline article is provided based on the two-dimensional data.

The superconducting solenoid magnet for the GEM detector poses unusual fabrication and handling challenges because of its extraordinary size. It will be more than 30% larger in diameter than the largest existing particle detector coils. Each of the two coil elements that compose the air-core solenoid, will be about 19 meters in diameter and 15 meters long. Major components weighing as much as 1500 Mg must be transported and manipulated at the Interaction Region 5 (IR5) fabrication site of the SSC Laboratory as the magnets are fabricated. Because of their large size, the magnets will be fabricated, assembled and tested at special purpose facilities at the IR5 site. The site-use plan must accommodate the fabrication of other detector components and the assembly of large flux shaping iron structures in a timely manner to allow subsequent testing and detector assembly. Each cold mass will be composed of twelve 45-Mg coil windings that are joined prior to assembly into the 19-m diam annular cryostat.