The goal for advanced steady-state operation in ITER should be to demonstrate the operation of the plasma core for a steady-state fusion reactor. To accomplish this the authors must develop steady-state operating scenarios at high beta for high fusion power density, low auxiliary power requirements (Q{sub CD} {ge} 25, where Q{sub CD} {triple_bond}P fusion/P{sub CD} and P{sub DC} is the power required for sustaining the plasma current) for low recirculating power requirements, and at moderate safety factor (q{sub {psi}} {le} 4.5) to minimize the cost for the tokamak core of a steady-state demonstration power reactor based on the operating modes demonstrated in ITER. The key to achieving steady-state operation at high fusion power in ITER will be the development of operating scenarios with very high bootstrap current fractions (f{sub BS} {ge} 90%) in which the radial profile of the bootstrap current density is well aligned with that of the total plasma current density, and for which the MHD {beta}-limit exceeds {beta}{sub n}{sup *} = 0.05 T{minus}m/MA. They are in the process of developing such operating modes for ITER. In {section}1 they propose two advanced steady-state operating points; a preliminary operating point that was the basis for the MHD studies reported …

Exact results for the Madelung constants and first order anharmonic energies are given for the inverse power potentials with the Coulomb potential as the softest example. Similar exact results are obtained using the analysis of Rosenfeld on the {Gamma} {yields} {infinity} limit for the OCP internal energy, direct correlation function, screening function, and bridge functions. Knowing these exact limits for the fluid phase of the OCP allows one to determine the nature of the thermal corrections to the strongly coupled results. Solutions of the HNC equation modified with the hard sphere bridge function give an example.

OAK-B135 Annual report Rockwell International Hot Laboratory decommissioning GFY 1992

Pressure sensors from ten MKS series 390 and 690 Baratron{reg_sign} capacitance manometers were hydrostatically burst tested by the Engineering and Materials Technology Department (E&MT). Four MKS series 390 Baratron{reg_sign} 0{minus}10 torr sensors had an average case burst pressure of 915 psig. Five MKS series 690 Baratron{reg_sign} 0{minus}1 torr sensors had an average case burst pressure of 1301 psig, and one MKS series 690 Baratron{reg_sign} 0{minus}1000 torr sensor had a case burst pressure of 938 psig.

This publication presents an annual summary of statistics at the national, Census division, State, electric utility, and plant levels regarding the quantity, quality, and cost of fossil fuels used to produce electricity. The purpose of this publication is to provide energy decision-makers with accurate and timely information that may be used in forming various perspectives on issues regarding electric power.

This engineering note documents the calculations done to determine the vacuum pumping speed for the D-Zero solenoid. The raw calculations are attached. A summary of the results are listed. The vacuum pumping speed of the solenoid is determined by the conductance of the pumping path. At higher pressure ranges during initial pumpdown, the conductances will be rather high. Calculations were not done for the transient pumpdown period, only the steady state type pumping situation. The pressure is assumed to be on the order of 10E-7 torr. This is the free molecular flow regime based on Knudsen number. This pressure regime is also where the pumping speed would be least. The conductances were calculated based on pumping helium gas at a temperature of 300 Kelvin. The total conductance of the pumping path from the solenoid to the inlet of the turbomolecular pump is 11.8 L/s. The effective pumping speed of a 1000 L/s turbo pump attached to this pumping path is 11.7 L/s. The minimum required pumping speed for design purposes was set at 4.3 L/s. This value was arrived at by assuming a warm leak size (10E-8 atm-cc/sec) was not detected during fabrication of the solenoid. It is then assumed …

Recent events regarding health and environmental problems associated with the use of chlorinated solvents have prompted the Oak Ridge Y-12 Plant to investigate substitutes for these materials. Since 1987, the purchase of chlorinated solvents at the Y-12 Plant has been reduced by 92%. This has been accomplished by substituting chlorinated solvent degreasing with ultrasonic aqueous detergent cleaning and by substituting chlorinated solvents with less toxic, environmentally friendly solvents for hand-wiping applications. Extensive studies of cleaning ability, compabitility, and effects on welding, bonding, and painting have been conducted to gain approval for use of these solvents. Toxicity and waste disposal were also assessed for the solvents.

The apparatus used for ammonia saturation and TPD (=temperature programmed desorption?) testing was modified to avoid repeated injections of NH{sub 3}. Saturation and TPD results are presented for potassium-doped {gamma}-alumina. In order to examine effects of Mo oxide promotion on catalytic activity of alumina-supported Rh catalyst, additional samples of Rh/{gamma}-Al{sub 2}O{sub 3} and Rh-Mo/{gamma}-Al{sub 2}O{sub 3} have been synthesized. 2 tabs, 3 figs.

In September 1989, the Occupational Safety and Health Administration (OSHA) issued a final ruling on lockout/tagout procedures. This ruling became effective in January 1990 and was eventually incorporated into the Code of Federal Regulations. The purpose of these procedures is to safeguard employees from hazardous energy while performing service or maintenance activities on machines and equipment. Approximately 39 million workers are protected by lockout/tagout procedures in general industry. OSHA estimates that adherence to the requirements in lockout/tagout procedures will eliminate nearly two percent of all workplace deaths. A lockout/tagout program is essential to the safe operation of all Department of Energy (DOE) facilities. The program outlined in this document consists of energy-control procedures, employee training and periodic inspections, and establishes the minimum requirements for lockout/tagout of equipment or system-energy sources that could cause injury to personnel. Because serious consequences can occur due to a lack of understanding and improper administration of this program, this document also includes a method for: Providing guidance for the control of hazardous energy, protecting employees from injury, defining responsibilities, and protecting equipment and facilities from damage.

We discuss dual-band infrared (DBIR) capabilities for imaging buried object sizes. We identify physical features affecting thermal contrast needed to distinguish buried object sites from undisturbed sites or surface clutter. Apart from atmospheric transmission and system performance, these features include: object size, shape, and burial depth; ambient soil, disturbed soil and object site thermal diffusivity differences; surface temperature, emissivity, plant-cover, slope, albedo and roughness variations; weather conditions and measurement times. We use good instrumentation to measure the time-varying temperature differences between buried object sites and undisturbed soil sites. We compare near surface soil temperature differences with radiometric infrared (IR) surface temperature differences recorded at 4.7 {plus_minus} 0.4 {mu}m and at 10.6 {plus_minus} 1.0 {mu}m. By producing selective DBIR image ratio maps, we distinguish temperature-difference patterns from surface emissivity effects. We discuss temperature differences between buried object sites, filled hole site (without buried objects), cleared (undisturbed) soil sites, and grass-covered sites (with and without different types of surface clutter). We compare temperature, emissivity-ratio, visible and near-IR reflectance signatures of surface objects, leafy plants and sod. We discuss the physical aspects of environmental, surface and buried target features affecting interpretation of buried targets, surface objects and natural backgrounds.

An explosive model has recently been designed and added to MACH2 to enable that code to be used as a tool for studying explosive magnetic flux compression generators. This report describes this model and gives examples of its use in both one- and two-dimensional simulations. A description of the model is given and one-dimensional simulations will be discussed. Also, we show examples of two-dimensional simulations. Appendices contain input decks for the one- and two-dimensional simulations and a listing of the modifications made to MACH2 for this purpose.

This paper discusses the physics and chemistry of non-thermal plasma processing for post-combustion NO{sub x} control in internal combustion engines. A comparison of electron beam and electrical discharge processing is made regarding their power consumption, radical production, NO{sub x} removal mechanisms, and by-product formation. Pollution control applications present a good opportunity for transferring pulsed power techniques to the commercial sector. However, unless advances are made to drastically reduce the price and power consumption of electron beam sources and pulsed power systems, these plasma techniques will not become commercially competitive with conventional thermal or surface-catalytic methods.

The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the general public. Written for the general public, the EIA publication Energy Information Sheets was developed to provide information on various aspects of fuel production, prices, consumption and capability. The information contained herein pertains to energy data as of December 1991. Additional information on related subject matter can be found in other EIA publications as referenced at the end of each sheet.

The proposed action is to recycle slightly activated copper that is currently stored in a warehouse leased by Lawrence Berkeley Laboratory (LBL) to a scrap metal dealer. Subsequent reutilization of the copper would be unrestricted. This document addresses the potential environmental effects of recycling and reutilizing the activated copper. In addition, the potential environmental effects of possible future uses by the dealer are addressed. Direct environmental effects from the proposed action are assessed, such as air emissions from reprocessing the activated copper, as well as indirect beneficial effects, such as averting air emissions that would result from mining and smelting an equivalent quantity of copper ore. Evaluation of the human health impacts of the proposed action focuses on the pertinent issues of radiological doses and protection of workers and the public. Five alternatives to the proposed action are considered, and their associated potential impacts are addressed. The no-action alternative is the continued storage of the activated copper at the LBL warehouse. Two recycling alternatives are considered: recycling the activated copper at the Scientific Ecology Group (SEG) facility for re-use at a DOE facility and selling or giving the activated copper to a foreign government. In addition, two disposal alternatives evaluate …

Japan emerged as the largest foreign direct investor in the U.S. economy in 1992, despite a sharp drop in the total value and number of U.S. businesses acquired and established by foreign investors. This change in Japan's status was spurred by a slight increase in investment spending by Japanese investors combined with a decrease in the British investment position. The foreign direct investment position in U.S. businesses and real estate - or the accumulated book value of all foreign investments - increased by $5 billion in 1992, the smallest change in two decades. Economists generally believe that foreign direct investment yields positive net benefits to both the host and the investing countries. For some American firms, the foreign investment inflows have been especially beneficial because they supplied the firms with funds during times when many U.S. commercial banks were unwilling to finance them.

This report covers the period from October 1, 1992 to March 1, 1993. The overall goals of the program task are to provide a final synthesis of six deep seismic reflection profiles and other geological and geophysical data from the southern Washington Cascades region where a probable extensive deep sedimentary basin has been discovered. This deep sedimentary basin is hypothesized from geological, regional magnetotelluric (MT), gravity, magnetic , and seismic reflection data as described in the American Association of Petroleum Geologists (AAPG) article by Stanley and others (1992). This report analyzed three seismic reflection profiles acquired by the Morgantown Energy Technology Centers in combination with the extensive MT and other data to outline a probable geological model for a thick conductive section of rocks in the southern Washington Cascades (called the Southern Washington Cascades conductor, SWCC). Earlier MT models suggested that the section consisted of an east-dipping package that extended to depths of as much as 20 km but appeared to surface in the Bear Canyon area near Morton, Washington and along the axis of the Carbon River and Morton anticlines. Interpretation of the first three DOE seismic reflection approximately confirmed the MT interpretation and added new information on anticlinal …

A graphical user interface (GUI) exists for building model geometry for the time-domain field code, AMOS. This GUI has recently been modified to build models and display the results of the Poisson electrostatic solver maintained by the Los Alamos Accelerator Code Group called POISSON. Included in the GUI is a 2-D graphic editor allowing interactive construction of the model geometry. Polygons may be created by entering points with the mouse, with text input, or by reading coordinates from a file. Circular arcs have recently been added. Once polygons are entered, points may be inserted, moved, or deleted. Materials can be assigned to polygons, and are represented by different colors. The unit scale may be adjusted as well as the viewport. A rectangular mesh may be generated for AMOS or a triangular mesh for POISSON. Potentials from POISSON are represented with a contour plot and the designer is able to mouse click anywhere on the model to display the potential value at that location. This was developed under the X windowing system using the Motif look and feel.

Laser pointing instability adds to the error of slope measurements taken with the Long Trace Profiler (LTP). As with carriage pitch error, this laser pointing error must be accounted for and subtracted from the surface under test (SUT) slope measurement. In the past, a separate reference beam (REF) allowed characterization of the component of slope error from carriage pitch. However, the component of slope error from laser pointing manifests itself differently in the SUT measured slope. An analysis of angle error propagation is given, and the effect of these errors on measured slope is determined. Then a method is proposed for identifying these errors and subtracting them from the measured SUT slope function. Separate measurements of carriage pitch and laser pointing instability isolate these effects, so that the effectiveness of the error identification algorithm may be demonstrated.

With Japan the United States has had one of its most important and most difficult trading relationships. Japan ranks second to Canada as the largest U.S. export market. It is also the second largest single source of imports to the United States. Trade issues are likely to become even more important as the whole U.S.-Japanese relationship changes in the post-Cold War period. How each country views and reacts to the other is changing as economic issues replace foreign policy and national security issues as the driving force of the relationship.

The study on forgings characterized machinability of the material by varying cutting speeds and feedrates utilizing four tools for the roughing operation and four tools for the semi-finish operation. Tools tested were obtained from four manufacturers. Twelve parts were machined utilizing an experimental design to determine all possible interactions between cutting speeds and feedrates. To evaluate the machinability of the material, quantitative measures in tool life, tool wear, surface finish, chip control, and material removal rates were analyzed. Benefits gained from this study are: higher material removal rates, longer tool life, minimal tool wear, improved chip control and reliability, increased productivity, and cost minimization.

Material removal rate, surface finish, and subsurface damage are largely governed by fracture mechanics and plastic deformation, when ceramics are machined using abrasive methods. A great deal of work was published on the fracture mechanics of ceramics in the late 1970s and early 1980s, although this work has never resulted in a comprehensive model of the fixed abrasive grinding process. However, a recently published model describes many of the most important features of the loose abrasive machining process, for example depth of damage, surface roughness, and material removal rate. Many of the relations in the loose abrasive machining model can be readily discerned from fracture mechanics models, in terms of material properties. By understanding the mechanisms of material removal, from a material properties perspective, we can better estimate how one material will machine in relation to another. Although the fracture mechanics models may have been developed for loose abrasive machining, the principles of crack initiation and propagation are equally valuable for fixed abrasive machining. This report provides a brief review of fracture in brittle materials, the stress distribution induced by abrasives, critical indenter loads, the extension of cracks, and the relation of the fracture process to material removal.

A grant was awarded to us by the Department of Energy, Office of Energy Research, in May 1987 to support the design and performance analysis of a large grain data-driven multiprocessor system for numerical applications. The basic idea of the work is to apply the data-driven principles of execution at a more appropriate level than conventional ``atomic`` instructions. For this purpose, a level such as that of vector operations was under study. This document represents the final report concerning the results of the research supported by this grant. The goals of the project entailed an analysis of Partial Differential Equation solvers on data-driven environments, a preliminary design of our multi-level architecture, an in-depth study of some of the mechanisms of execution, and a design of the software environment. As enumerated in the original proposal, our work has yielded results in three different domain: Specifications of the application programs; design of the general concepts of the architecture and simulation; implementation of a translating environment; and we discuss each of the above items and examine specific research results.

This report discusses how the US can play a productive mediating role in South Asia by engaging India and Pakistan in an international forum to manage nuclear weapons, as Edward Teller advocated. India and Pakistan have developed their nuclear capabilities because they fear their neighbors, not because they want to threaten fear their neighbors, not because they want to threaten the US. The appropriate response for the US, therefore, is diplomatic engagement and negotiations. In addition to the international approach, encouragement and facilitation of regional and bilateral interactions will also be important. Formal arms control agreements have been reached, but less formal confidence-building measures, and unilateral security pledges may well be combined to form a more secure strategic environment in South Asia than a nuclear armed confrontation across the porous South Asian border.

My subject this morning is a very brief overview of the Chemical Weapons Convention. Much has already been written describing and summarizing the Convention, including several of the Supplementary Papers and the Annex contained within the draft Manual. It is not my goal to restate what many of you already know. Rather, in the short time available, I want to focus on the parts of the Convention that are addressed in the draft Manual, that is, I want to highlight for you those aspects of the CWC that require implementation by individual State Parties. As I do so, I will show you where in the draft Manual each of these matters is addressed so that you can see how our document corresponds to the Convention`s requirements. This will provide a bridge between the plenary sessions and workshops that will consider the implementing measures and the Supplementary Papers in the Manual. In organizing my talk to focus on aspects of the Convention requiring national implementing measures, I necessarily leave out certain of its provisions. Among these intentional omissions are, with all due respect to our hosts, the structure and function of the OPCW, the Annex on Chemicals, and various operational aspects …