This program includes six tasks, including (1) a project measuring the performance of unique solar system components, (2) a project to develop a methodology for determining annual performance ratings of solar domestic hot water systems, (3) a project that will identify, analyze, design, build, and experimentally evaluate SDHW systems incorporating advanced concepts and components, (4) a liquid desiccant cooling system development project, (5) a project that will perform TRNSYS simulations to determine potential energy savings for desiccant cooling systems, especially in humid climates, and (6) a management task. The objectives and progress in each task are described.

This program includes six tasks, including (1) a project measuring the performance of unique solar system components, (2) a project to develop a methodology for determining annual performance ratings of solar domestic hot water systems, (3) a project that will identify, analyze, design, build, and experimentally evaluate SDHW systems incorporating advanced concepts and components, (4) a liquid desiccant cooling system development project, (5) a project that will perform TRNSYS simulations to determine potential energy savings for desiccant cooling systems, especially in humid climates, and (6) a management task. The objectives and progress in each task are described.

The objective of ``Detailed Evaluation of the West Kiehl Alkaline-Surfactant-Polymer Field Project and It`s Application to Mature Minnelusa Waterfloods`` is to (1) quantify the incremental oil produced from the West Kiehl alkaline-surfactant-polymer project by classical engineering and numerical simulation techniques, (2) to quantify the effect of chemical slug volume injection on incremental oil in the two swept areas of the field, (3) to determine the economic ramifications of the application of the alkaline-surfactant-polymer technology, (4) to forecast the results of injecting an alkaline-surfactant-polymer solution to mature waterfloods and polymer floods, and (5) to provide the basis for independent operators to book additional oil reserves by using the alkaline-surfactant-polymer technology. This report documents the initial geological and reservoir engineering data gathering. In addition, some of the initial laboratory results are discussed. Some evaluation of the West Kiehl has been published.

Two types of fast bolometers are described for the plasma energy transport study in the Madison Symmetric Torus plasma confinement device. Both types use pyrocrystals of LiTaO[sub 3] or LiNbO[sub 3] as the sensors. One type is used for measurements of the radiated heat losses and is situated at the vacuum shell inner surface. Another type is insertable in the plasma and measures the plasma particle heat flux. The frequency response of the bolometers is measured to be in the 150--200 kHz range. The range of the measured power fluxes is 0.1 W/cm[sup 2] 10 kW/cm[sup 2] and can be adjusted by changing the size of the entrance aperture. The lower limit is determined by the amplifier noise and the frequency bandwidth, the higher limit by destruction of the bolometer sensor.

Two types of fast bolometers are described for the plasma energy transport study in the Madison Symmetric Torus plasma confinement device. Both types use pyrocrystals of LiTaO{sub 3} or LiNbO{sub 3} as the sensors. One type is used for measurements of the radiated heat losses and is situated at the vacuum shell inner surface. Another type is insertable in the plasma and measures the plasma particle heat flux. The frequency response of the bolometers is measured to be in the 150--200 kHz range. The range of the measured power fluxes is 0.1 W/cm{sup 2} 10 kW/cm{sup 2} and can be adjusted by changing the size of the entrance aperture. The lower limit is determined by the amplifier noise and the frequency bandwidth, the higher limit by destruction of the bolometer sensor.

I have reported most of the results of my adhesive testing to members of the VLPC design team at one time or another, usually verbally, but I am wnnng this summary as an easy reference to the results I obtained. The adhesives I tested were for two primary purposes. The first was adhering optical fibers to Torlon 7130; the other was for securing an aluminum nitride substrate to the same material. I have not had access to a scanning electron microscope and someone with the knowledge to determine actual failure mechanisms, so the deductions I have made about why some adhesives have worked well at low temperatures for some purposes and not for other applications while a different material never worked and another always worked are partially speculation. They should be taken merely at face value with no particular results 'carved in stone' so to speak. The first aspect of my testing was adhesion of optical fiber to torlon. Knowing that this is a very important joint, I tested a variety of glues of two primary types: acrylic and W cure. W cure adhesives are known to possess reasonably good properties at low temperatures and are quite convenient to use …

If the 103rd Congress embarks upon an effort to reauthorize the Endangered Species Act (ESA), it will run into an old acquaintance: the property rights issue. As now written, the ESA has at least the potential to curtail property rights (whatever its actual impact as implemented may be). This report explores the legal repercussions of those impacts, especially whether they constitute takings of property under the fifth amendment of the U.S. Constitution.

This report discusses research on nuclear masses and nuclear structure far from stability.

Vehicles powered by fuel cells operate more efficiently, more quietly, and more cleanly than internal combustion engines (ICEs). Furthermore, methanol-fueled fuel cell vehicles (FCVs) can utilize major elements of the existing fueling infrastructure of present-day liquid-fueled ICE vehicles (ICEVs). DOE has maintained an active program to stimulate the development and demonstration o fuel cell technologies in conjunction with rechargeable batteries in road vehicles. The purpose of this study is to identify and assess the availability of data on FCVs, and to develop a vehicle subsystem structure that can be used to compare both FCVs and ICEV, from a number of perspectives--environmental impacts, energy utilization, materials usage, and life cycle costs. This report focuses on methanol-fueled FCVs fueled by gasoline, methanol, and diesel fuel that are likely to be demonstratable by the year 2000. The comparative analysis presented covers four vehicles--two passenger vehicles and two urban transit buses. The passenger vehicles include an ICEV using either gasoline or methanol and an FCV using methanol. The FCV uses a Proton Exchange Membrane (PEM) fuel cell, an on-board methanol reformer, mid-term batteries, and an AC motor. The transit bus ICEV was evaluated for both diesel and methanol fuels. The transit bus FCV runs …

The Electric Power Monthly is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions.

Objective is to understand the mechanisms governing nonequilibrium plasma atomistic or molecular deposition of hard face coatings. Laser diagnostic methods include coherent anti-Stokes Raman spectroscopy (CARS) and laser-induced fluorescence. TiB[sub 2] and diamonds were used as the hard face coating materials. Diborane was used as precursor to TiB[sub 2].

Objective is to understand the mechanisms governing nonequilibrium plasma atomistic or molecular deposition of hard face coatings. Laser diagnostic methods include coherent anti-Stokes Raman spectroscopy (CARS) and laser-induced fluorescence. TiB{sub 2} and diamonds were used as the hard face coating materials. Diborane was used as precursor to TiB{sub 2}.

Hydrogen generation data obtained from IDMS runs PX4 and PX5 will be used to determine a bases for a deflagration/detonation simulation in the DWPF CPC. This simulation is necessary due to the new chemistry associated with the Late Wash/ Nitric Acid flowsheet and process modifications associated with the presence of H{sub 2} in the offgas. The simulation will be performed by Professor Van Brunt from the University of South Carolina. The scenario which leads up to the deflagration/detonation simulation will be chosen such that the following conditions apply. The SRAT is filled to its maximum operating level with 9,600 gal of sludge, which corresponds to the minimum vapor space above the sludge. The SRAT is at the boiling point, producing H{sub 2} at a very low rate (about 10 % of the peak) and 15 scfm of air inleakage is entering the SRAT. Then, the H{sub 2} generation rate will be allowed to increase exponentially (catalyst activation) until it readies the peak H{sub 2} generation rate of the IDMS run, after which the H{sub 2} generation rate will be allowed to decay exponentially (catalyst deactivation) until the total amount of H2 produced is between 85 and 100% of that produced …

We have measured solute trapping of Sn in Al over a wide enough range of velocities to make a quantitative test of theory. The Continuous Growth Model of Aziz is the only one-parameter model that fits the data. We have also measured the diffusive speed - the growth rate at which interfacial partitioning is in mid-transition between equilibrium partitioning and complete solute trapping - for several solutes in A1. We have found an inverse correlation between the equilibrium partition coefficient and the diffusive speed. Taken together, these results give us heretofore unprecedented predictive capability in modeling rapid solidification processing. We have also examined theoretically short-range diffusion-limited growth, characteristic of incomplete solute trapping, and interface-limited growth, characteristic of complete solute trapping, in alloy solidification and have shown that the two regimes fall naturally out of a single unified theory of solidification.

We have measured solute trapping of Sn in Al over a wide enough range of velocities to make a quantitative test of theory. The Continuous Growth Model of Aziz is the only one-parameter model that fits the data. We have also measured the diffusive speed - the growth rate at which interfacial partitioning is in mid-transition between equilibrium partitioning and complete solute trapping - for several solutes in A1. We have found an inverse correlation between the equilibrium partition coefficient and the diffusive speed. Taken together, these results give us heretofore unprecedented predictive capability in modeling rapid solidification processing. We have also examined theoretically short-range diffusion-limited growth, characteristic of incomplete solute trapping, and interface-limited growth, characteristic of complete solute trapping, in alloy solidification and have shown that the two regimes fall naturally out of a single unified theory of solidification.

Research and development in support of the DWPF began during the 1970`s at the Savannah River Technology Center (formerly the Savannah River Laboratory). A large amount of data relevant to compliance with the Waste Acceptance Product Specifications (WAPS) was generated prior to the preparation and issue of the WAPS. Thus, most of this data was not generated under a quality assurance program which meets the Office of Civilian Radioactive Waste Management`s requirements. The DWPF has developed a plan for qualification of existing data sets which will be used to establish compliance with the WAPS, which is reported here. In this document, the existing data sets which will be used for compliance are identified, and the method(s) of qualification of each data set for use in the Waste Form Qualification Report is defined. This document thus provides a link between the detailed descriptions of all of the compliance activities in the Waste Form Compliance Plans (WCP), and the requirements for qualification of existing data sets used for compliance purposes. All of these data sets will be qualified by the end of Qualification Runs in the DWPF.

Report summarizing federal aid for elementary and secondary education, with a focus on the proposals of Goals 2000.

Progress was made in the following areas: radioinduced segregation (modeling and experiment), deformation of irradiated microstructures, stress corrosion cracking of irradiated microstructures, and development of an apparatus to determine the role of deformation on the radiation microstructure in-situ. Materials used were based on Ni-Cr-Fe and 304L.

The roughly 0.5-km{sup 2} (0.2-mi{sup 2}) Hanford Waste Vitrification Plant (WHVP) site is located in the Pasco Basin in south-central Washington State at the US Department of Energy`s Hanford Site. The HWVP site is planned for use as a waste treatment facility for treating the high-activity fraction of waste currently stored in underground storage tanks on the Hanford Site. In order to determine the pre-construction chemical properties of the proposed construction site soils and to enable the HWVP to segregate these, as necessary, from any impact of HWVP operations, a soil baseline sampling plan was written and implemented. The report describes the baseline sampling plan.

The objectives of this project are to test novel fullerene based catalysts for application in methane activation. Fullerenes are a recently discovered allotrope of carbon that have been found to possess unusual properties, some of which may be ideal for methane conversion to higher hydrocarbons. The project is divided into three technical tasks. Task 1 deals with the synthesis and characterization of the fullerenes and fullerene soots, Task 2 with the testing of the catalysts, and Task 3 with the evaluation of the results and technical reporting requirements. This quarter we prepared fullerene soot and conducted experiments to determined its reactivity towards methane, hydrogen, and ethylene. The results are summarized: (1) Soot containing approximately 12-14 wt % fullerenes was prepared by the discharge method of Haufler et al. SRI is in the process of developing methodology to produce large scale amounts of fullerenes and fullerene based materials and is working with a private company to that end. In order to provide a background of fullerene soot and describe some of these methods we have included Appendix A. (2) We conducted some preliminary experiments in order to determine the temperature regime at which fullerene based soot would begin to be active …

An active neutron interrogation system utilizing the differential die-away technique (DDT), was built to assay fissile material in small waste packages for a variety of matrices. Within minutes the system can make a ``go/no-go`` decision for sorting low-level waste (LLW) from transuranic waste (TRUW). It can also provide gram-level accountability of weapons-grade (WG) Pu in TRUW providing lumps of self-shielding fissile material are absent.

The initial work on the synthesis of MTBE during CO hydrogenation shows that MTBE cannot be formed directly on metal sites and likely requires the presence of an acid site. However, MTBE can be made successfully when an acid site, provided by the zeolites, is present in the vicinity of the methanol-synthesis metal sites. When i-butylene was added during CO hydrogenation over a composite catalyst consisting of Li-Pd/SiO{sub 2} and a hydrogen-zeolite, MTBE was formed in measurable amounts. The major by-product of this reaction scheme was isobutane and the dimer of i-butylene. In general, ZSM-5 was found to be superior to LZ210-12 HY zeolite. CO hydrogenation over a bifunctional PdNaY catalyst shows that branched hydrocarbons as well as MEOH can be made successfully at the same time. Addition of i-butylene over this catalyst only (i.e. without other zeolite) results in the formation of trace amounts of MTBE.

Two essays are included in this booklet. Their titles are ``The Dynamics of the NPT Extension Decision`` and ``North Korea`s Nuclear Gambit.`` The first paper discusses the conference to be held in 1995 to review the Nuclear Non-Proliferation Treaty (NPT) which will decide whether the treaty shall continue in force indefinitely, or shall be extended for an additional fixed period or periods. Topics relevant to this discussion are: Arms control issues, the nuclear test ban, the limited test ban treaty, the French nuclear testing moratorium, former Soviet nuclear weapons, Iraq, North Korea, nuclear-weapon-free zones, security, controls on nuclear weapon materials, peaceful uses of nuclear energy, safeguards, politics, and organizational and procedural issues. The second paper examines short, medium, and long term issues entailed in Korea`s nuclear proliferation. Topics considered include: Korean unification, North Korean politics, the nuclear issue as leverage, and the Nuclear Non- Proliferation Treaty.

The investigations with the anion exchange resin Reillex{trademark}-HPQ is continuing along several different paths. The topics of current investigations that are reported here are: The sorption behavior of chromium(VI) on Reillex{trademark}-HPQ from nitric acid solutions and from sodium hydroxide/sodium nitrate solutions; sorption behavior of F{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; sorption behavior of Cl{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; sorption behavior of Br{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; and the Honors thesis by one of the students is attached as Appendix II (on ion exchange properties of a new macroperous resin using bromide as the model ion in aqueous nitrate solutions).