A 250-GHz Cyclotron Auto Resonance Maser (CARM) oscillator has been designed and constructed and will be tested using a 1-kA, 2-MeV electron beam produced by the induction linac at the Accelerator Research Center (ARC) facility of Lawrence Livermore National Laboratory (LLNL). The oscillator circuit was made to operate in the TE{sub 11} mode at ten times cutoff using waveguide Bragg reflectors to create an external cavity Q of 8000. Theory predicts cavity fill times of less than 30 ns (pulse length) and efficiencies approaching 20% is sufficiently low transverse electron velocity spreads are maintained (2%).

The anisotropic deformation of foliated and linealed rocks has been investigated, primarily to predict the mechanical response of rocks surrounding buried magma chambers to the stress fields generated by deep drilling. The principal application in this regard has been to evaluate, the scientific feasibility of extracting geothermal energy from buried magma chambers. Our approach has been to perform triaxial extension and compression tests at temperatures and pressures representative of the borehole environment on samples cored along six selected orientations and to fit the data to an orthohombric yield criterion. We have investigated Four-Mile gneiss (a strongly layered gneiss with well defined lineation), a biotite-rich schist, and Westerly granite (using a block oriented with respect to the granite's rift, grain, and hardway). Progress has been made in three areas: the experimental determination of strength anisotropies for the three starting materials, theoretical treatment and modeling of the results, and characterization of fabrics surrounding magma bodies resulting from their diaperic emplacement into shallow portions of the Earth's crust. In addition, results have been obtained for the tensile fracture of quartzite, basal slip and anisotropy of biotite single crystals, and anisotropic flow of bedded rocksalt.

The anisotropic deformation of foliated and linealed rocks has been investigated, primarily to predict the mechanical response of rocks surrounding buried magma chambers to the stress fields generated by deep drilling. The principal application in this regard has been to evaluate, the scientific feasibility of extracting geothermal energy from buried magma chambers. Our approach has been to perform triaxial extension and compression tests at temperatures and pressures representative of the borehole environment on samples cored along six selected orientations and to fit the data to an orthohombric yield criterion. We have investigated Four-Mile gneiss (a strongly layered gneiss with well defined lineation), a biotite-rich schist, and Westerly granite (using a block oriented with respect to the granite`s rift, grain, and hardway). Progress has been made in three areas: the experimental determination of strength anisotropies for the three starting materials, theoretical treatment and modeling of the results, and characterization of fabrics surrounding magma bodies resulting from their diaperic emplacement into shallow portions of the Earth`s crust. In addition, results have been obtained for the tensile fracture of quartzite, basal slip and anisotropy of biotite single crystals, and anisotropic flow of bedded rocksalt.

New equations for continuous, operational interpolation on four plates in rectangular array are derived. The equations can be applied to the interpretation of experimental data. Other topics include convergence of operational formulas and extrapolation by operational methods. 11 refs.

With increasing environmental concerns regarding the handling and storage of uranium waste, recycling previously used material is becoming exceedingly more important. Carbon is one of the primary trace impurities that builds up in uranium with repeated use. The goal of this study is to reduce carbon in recycled uranium during the casting process to carbon levels associated with virgin uranium derbies. Vacuum-induction casting experiments have demonstrated that hafnium (Hf) additions to unalloyed uranium (U) reduce carbon (C) levels by approximately 80% in up to 6.0 in. in depth in 5 {times} 7 {times} 15 in. (width {times} depth {times} thickness) book mold castings. Analytic modeling of the solidification process was initiated to compare the calculated/predicted thermal profile to the actual experimentally measured temperatures. Temperature profile predictions matched the experimental values at the top of the casting and accurately determined that the predominant heat loss is out of the bottom of the book mold assembly. However, the model overpredicts the temperature half way down the length of the casting. The boundary heat transfer coefficient at the bottom of the casting needs to be more accurately simulated. 4 refs., 5 figs., 3 tabs.

Work has continued on characterizing the kinetics of lignin peroxidases and has now expanded to include the chemistry of Mn peroxidases. Progress in these two area in addition to the authors work on the molecular biology of lignin biodegradation is briefly described below. Copies of two reprints and one preprint which have resulted from the work are attached.

This paper discusses work being conducted in High Energy Physics and Nuclear Physics where theory and experiment go hand in hand. Pion capture, proton-antiproton interactions, kaon-pion interactions and hypernuclei decay are discussed as examples. (LSP)

Research on promoted metal oxide catalysts has continued with the study of alkaline earth/metal oxide halide catalysts. A barium bromide/alumina catalyst was comparable in methane conversion and selectivity to C{sub 2}'s to barium chloride/alumina catalysts. The effects of varying methane to oxygen feed ratios were explored for one of the best alkaline earth catalysts and one of the best literature catalysts (Li/MgO). A significant decrease in the selectivity to C{sub 2}'s is observed upon addition of ethane to the feed gas (feed gas methane/ethane ratio of 3). This observation demonstrates that a significant amount of ethane should not be recycled during methane oxidation over these types of catalysts under process conditions used. Methane oxidation over barium carbonate alone results in high enough selectivities and methane conversions to suggest an oxidized barium species may be responsible for methane oxidation on barium/metal oxide catalysts. Methane coupling studies have continued using layered perovskite catalysts in the cofeed mode and double perovskite catalysts in the sequential mode. Addition of sodium to the double perovskite LaCaMnCoO{sub 6} resulted in a catalyst with improved selectivity over the one without sodium. A reactor system containing two reactors in under construction. These reactors will be used to study …

Much of the equipment and instrumentation in the Pu-238 production facilities is more than 15 years old. Significant improvements have been made in the available instrumentation, in particular, due to the application of microprocessors and lasers. The Actinide Technology Section of SRL has selected and is in the process of evaluating several state-of-the-art instruments which have potential applications in the Pu-238 program. The ease of operation and the accuracy of the instruments have been improved and, in most cases, the cost of the instruments have decreased. 5 refs.

Disclosed is a method for producing a superconductor of the R-Ba-Cu-O system which comprises of selecting an insulating material of the formula RBa{sub x}Cu{sub y}O{sub z} where R is selected from the group consisting of Y, La, Pr, Nd, Sm, Eu, Gd, Ho, Er, Tm, and Lu, and where x ranges from about 1.7 to about 2.3, y ranges from about 2.7 to about 3.3 and z ranges from about 5.0 to about 6.99, and halogenating said material with a halogen selected from the group consisting of chlorine, bromine, iodine, and mixtures thereof, while maintaining said material at a temperature ranging from about 160 to about 440{degrees}C, for a period of time sufficient to cause incorporation of said halogen into said material. Also, disclosed are the materials produced by the method and articles of manufacture incorporating said materials as electronic circuitry components.

The design of the heavy-ion beam and the HYLIFE-II reactor chamber interface must provide final focusing quadruple triplets, neutron shielding, fast shutters, vapor condensation and pumping, thermal insulation, and blast resistant structures. The smallest half angle encompassing all beams striking the target might be {plus minus}14{degrees} for an array of 4 {times} 4 beams or {plus minus}9{degrees} if the four corner beams are eliminated, giving a 12-beam array. The target gain drops considerably from the 0{degree} published values because of this finite angle. The assumed one-sided irradiation reduces the number of bending magnets. A 350-MJ yield might be achieved with a 6-MJ driver (gain of 58) (nominal 1000 MWe net power with a repetition rate of 8 Hz). For either lower repetition rate or lower gain the yield must be increased by increasing the driver energy. The beam ports are protected from radiation by an array of vertical and horizontal, neutronically-thick, liquid jets. 6 refs., 7 figs.

The Tritium Emissions Reduction Facility (TERF) is being built by EG G Mound Applied Technologies to provide improved control of the tritium emissions from gas streams being processed. Mound handles tritium in connection with production, development, research, disassembly, recovery, and surveillance operations. During these operations, a small fraction of the tritium being processed escapes from its original containment. The objective of this report is to describe the human factors engineering as performed in connection with the design, construction, and testing of the TERF as required in DOE Order 6430.1A, section 1300-12. Human factors engineering has been involved at each step of the process and was considered during the preliminary research on tritium capture before selecting the specific process to be used. Human factors engineering was also considered in determining the requirements for the TERF and when the specific design work was initiated on the facility and the process equipment. Finally, human factors engineering was used to plan the specific acceptance tests that will be made during TERF installation and after its completion. These tests will verify the acceptability of the final system and its components. 16 refs., 8 figs.

We are examining the effects on composition and behavior of Argonne-supplied Wyodak coal under both thermal (no added water/N{sub 2}) and hydrothermal (liquid water/N{sub 2}) conditions at 350{degree}C for periods of 30 min and 5 hr, with emphasis during this period on the longer treatment. Field ionization mass spectrometry (FIMS) of the untreated, thermally treated, and hydrothermally treated coals is conducted at conditions where the samples are heated from ambient to 500{degree}C at 2.5{degree}/min. In the 5 hr work the volatilities of the coals are 24%, 16%, and 25% respectively. Solvent swelling studies with the recovered coals do not demonstrate the expected lower degree of crosslinking in the hydrothermal case. Both the thermal and hydrothermal treatments yield products with a decreased swelling ratio, but the ratio for the product from the aqueous treatment is slightly lower than that from thermal treatment. At present we cannot reconcile this result with our other data. 4 refs., 6 figs.

The HYLIFE-2 inertial fusion power plant design study uses a liquid fall, in the form of jets to protect the first structural wall from neutron damage, x rays, and blast to provide a 30-y lifetime. HYLIFE-1 used liquid lithium. HYLIFE 2 avoids the fire hazard of lithium by using a molten salt composed of fluorine, lithium, and beryllium (Li{sub 2}BeF{sub 4}) called Flibe. Access for heavy-ion beams is provided. Calculations for assumed heavy-ion beam performance show a nominal gain of 70 at 5 MJ producing 350 MJ, about 5.2 times less yield than the 1.8 GJ from a driver energy of 4.5 MJ with gain of 400 for HYLIFE-1. The nominal 1 GWe of power can be maintained by increasing the repetition rate by a factor of about 5.2, from 1.5 to 8 Hz. A higher repetition rate requires faster re-establishment of the jets after a shot, which can be accomplished in part by decreasing the jet fall height and increasing the jet flow velocity. Multiple chambers may be required. In addition, although not considered for HYLIFE-1, there is undoubtedly liquid splash that must be forcibly cleared because gravity is too slow, especially at high repetition rates. Splash removal can …

The HYLIFE-2 inertial fusion power plant design study uses a liquid fall, in the form of jets to protect the first structural wall from neutron damage, x rays, and blast to provide a 30-y lifetime. HYLIFE-1 used liquid lithium. HYLIFE 2 avoids the fire hazard of lithium by using a molten salt composed of fluorine, lithium, and beryllium (Li{sub 2}BeF{sub 4}) called Flibe. Access for heavy-ion beams is provided. Calculations for assumed heavy-ion beam performance show a nominal gain of 70 at 5 MJ producing 350 MJ, about 5.2 times less yield than the 1.8 GJ from a driver energy of 4.5 MJ with gain of 400 for HYLIFE-1. The nominal 1 GWe of power can be maintained by increasing the repetition rate by a factor of about 5.2, from 1.5 to 8 Hz. A higher repetition rate requires faster re-establishment of the jets after a shot, which can be accomplished in part by decreasing the jet fall height and increasing the jet flow velocity. Multiple chambers may be required. In addition, although not considered for HYLIFE-1, there is undoubtedly liquid splash that must be forcibly cleared because gravity is too slow, especially at high repetition rates. Splash removal can …

The overall objective of this project is to produce antibodies to unique modified DNA bases and develop immunochemical assays to quantitate these lesions in damaged DNA. During this past year we have developed an antibody and chemical test to quantitate a basic sites in DNA and produced antibodies to the 8-oxopurines. This report discusses the detection of a basic sites in DNA and the preparation of antibodies to 8-hydroxyadenine and 8-hydroxyguanine.

Black spots and other blemishes were found on the inside surface of small stainless steel pressure vessels by borescope inspection. Most of the black spots originated from pyrolysis of lint contaminating the interior surface of these parts prior to welding. The lint originated from cotton gloves used to handle parts and from cotton gauze used to clean the parts. Pyrolysis of other hydrocarbons can also create black spots. 34 figs.

This paper discusses lattice automata models for earthquakes and frictional sliding. (JEF)

This document is the February 14, 1990 version of the LLNL Waste Minimization Program Plan (WMPP). The Waste Minimization Policy field has undergone continuous changes since its formal inception in the 1984 HSWA legislation. The first LLNL WMPP, Revision A, is dated March 1985. A series of informal revision were made on approximately a semi-annual basis. This Revision 2 is the third formal issuance of the WMPP document. EPA has issued a proposed new policy statement on source reduction and recycling. This policy reflects a preventative strategy to reduce or eliminate the generation of environmentally-harmful pollutants which may be released to the air, land surface, water, or ground water. In accordance with this new policy new guidance to hazardous waste generators on the elements of a Waste Minimization Program was issued. In response to these policies, DOE has revised and issued implementation guidance for DOE Order 5400.1, Waste Minimization Plan and Waste Reduction reporting of DOE Hazardous, Radioactive, and Radioactive Mixed Wastes, final draft January 1990. This WMPP is formatted to meet the current DOE guidance outlines. The current WMPP will be revised to reflect all of these proposed changes when guidelines are established. Updates, changes and revisions to the …

A method for producing homogenous single crystal III--V ternary alloys of high crystal perfection using a floating crucible system in which the outer crucible holds a ternary alloy of the composition desired to be produced in the crystal and an inner floating crucible having a narrow, melt-passing channel in its bottom wall holds a small quantity of melt of a pseudo-binary liquidus composition which would freeze into the desired crystal composition. The alloy of the floating crucible is maintained at a predetermined lower temperature than the alloy of the outer crucible, and a single crystal of the desired homogeneous alloy is pulled out of the floating crucible melt, as melt from the outer crucible flows into a bottom channel of the floating crucible at a rate that corresponds to the rate of growth of the crystal.

The effectiveness of water sprays to absorb HF releases has been recently demonstrated by extended laboratory and field tests. In this paper computer simulations are presented of the Hawk, Nevada Test Site, series of field tests, along with parametric studies of several cases which have not been studied in the field. The model used in these simulations, HFSPRAY, treats the gas-phase as an Eulerean fluid whereas the spray is described according to the Lagrangian approach by a finite number of drops of varying size and trajectory. HFSPRAY simulates the momentum, mass and energy interactions between a water spray and a turbulent plume of HF in air; it is capable of predicting the flow velocities, temperature, water vapor and HF concentration fields in two-dimensional large-geometries, for spraying in any direction, (i.e., down-flow, inclined-down-flow, up-flow, and co-current horizontal flow). 15 refs., 21 figs.

The objective of this project is to produce one or more microorganisms capable of removing the organic and inorganic sulfur in coal. The original specific technical objectives of the project were to: clone and characterize the genes encoding the enzymes of the ``4S`` pathway (sulfoxide/sulfone/sulfonate/sulfate) for release of organic sulfur from coal; return multiple copies of genes to the original host to enhance the biodesulfurization activity of that organism; transfer this pathway into a fast-growing chemolithotropic bacterium; conduct a batch-mode optimization/analysis of scale-up variables.

The objective of this project is to produce one or more microorganisms capable of removing the organic and inorganic sulfur in coal. The original specific technical objectives of the project were to: clone and characterize the genes encoding the enzymes of the 4S'' pathway (sulfoxide/sulfone/sulfonate/sulfate) for release of organic sulfur from coal; return multiple copies of genes to the original host to enhance the biodesulfurization activity of that organism; transfer this pathway into a fast-growing chemolithotropic bacterium; conduct a batch-mode optimization/analysis of scale-up variables.

The objective of this project is to produce one or more microorganisms capable of removing the organic and inorganic sulfur in coal. The specific technical objectives of the project are to: clone and characterize the genes encoding the enzymes of the 4S'' pathway (sulfoxide/sulfone/sulfonate/sulfate) for release of organic sulfur from coal; return multiple copies of genes to the original host to enhance the biodesulfurization activity of that organism; transfer this pathway into a fast-growing chemolithotrophic bacterium; and conduct a batch-mode optimization/analysis of scale-up variables. This report presents the results of research at Battelle during the 5th Quarterly Report period beginning on June 15, 1990. 1 ref., 6 figs., 4 tabs.