"An airplane in steady rectilinear flight was assumed to experience an initial disturbance in rolling or yawing velocity. The equations of motion were solved to see if it was possible to hasten recovery of a stable airplane or to secure recovery of an unstable airplane by the application of a single lateral control following an exponential law. The sample computations indicate that, for initial disturbances complex in character, it would be difficult to secure correlation with any type of exponential control" (p. 1).

"Extensive strain-gage measurements were made chiefly on the tension side of five small rectangular box beams constructed of sheet duralumin. The main conclusion was that within the test range the tension cover may be considered as being fully effective but that at any given point on the beam there may be unaccountable variations of 5 percent from the calculated stresses on the thicker sheets tested (0.044 and 0.023 inch) and of 10 percent or more on the thinnest sheet tested (0.014 inch)" (p. 1).

The discharge characteristics of two similar injection valves operated by a single-cylinder fuel-injection pump were determined with an apparatus that measured the quantity of fuel discharged from each valve during every 0.5 degrees of pump rotation. It was found that similar discharges took place from the two valves at all pump speeds when the valve-opening pressures, the nozzle-orifice diameters, and the injection-tube lengths were the same for both valves. Under these conditions, the effects of changing the pump speed, the pump throttle setting, or the nozzle orifice diameter were very similar to those occurring with a single-injection valve. By a proper selection of discharge-orifice areas and valve-opening pressures it was possible to obtain a great many combinations of discharge quantities, discharge rates, and injection timings for the two valves. A series of tests using injection tubes of unequal lengths for the two valves showed that under these conditions the injection timing and the fuel quantity discharged from each valve varies widely and erratically with changes in the pump speed.

"Experimental and analytical studies were made of solid and hollow deep rectangular beams to study their lateral instability under various conditions of loading and restraint. The tests were made on bars and tubes of 17ST aluminum alloy. Failure by lateral buckling occurred only in tests on the solid beams. It was found that, within the elastic range, the test results were in agreement with the classical theory for the lateral buckling of deep beams as given by Prandtl, Mitchell, and Timoshenko" (p. 1).

Discussed here are results already achieved with sonic altimeters in light of the theoretical possibilities of such instruments. From the information gained in this investigation, a procedure is outlined to determine whether or not a further development program is justified by the value of the sonic altimeter as an aircraft instrument. The information available in the literature is reviewed and condensed into a summary of sonic altimeter developments. Various methods of receiving the echo and timing the interval between the signal and the echo are considered. A theoretical discussion is given of sonic altimeter errors due to uncertainties in timing, variations in sound velocity, aircraft speed, location of the sending and receiving units, and inclinations of the flight path with respect to the ground surface. Plots are included which summarize the results in each case. An analysis is given of the effect of an inclined flight path on the frequency of the echo. A brief study of the acoustical phases of the sonic altimeter problem is carried through. The results of this analysis are used to predict approximately the maximum operating altitudes of a reasonably designed sonic altimeter under very good and very bad conditions. A final comparison is made …

From Summary: "Engine test results are presented for simulated altitude conditions. A displaced-piston combustion chamber on a 5- by 7-inch single cylinder compression-ignition engine operating at 2,000 r.p.m. was used. Inlet air temperature equivalent to standard altitudes up to 14,000 feet were obtained. Comparison between performance at altitude of the unsupercharged compression-ignition engine compared favorably with the carburetor engine."

A study has been made of the important principles involved in the operation of a baffle for an engine cylinder and shows that cooling can be improved by 20 percent by using a correctly designed baffle. Such a gain is as effective as a 65 percent increase in pressure drop across the standard baffle, which had a 1/4 inch clearance between baffle and fin tips.

Various methods of measuring the air speed of airplanes are described. Particular emphasis is placed on the procedure required to obtain precise measurements of speed by the use of the suspended Pitot-static head or the suspended static head. Typical calibration curves for service installations of Pitot-static heads are shown and the relation between errors in air speed and corresponding errors in observed altitude for such installations is discussed. There is included a brief discussion of various speed-course methods of measuring speed.

An analysis of existing pressure-distribution data was made to determine the variation of the tip loading with wing plan form. A series of empirical tip corrections was derived that may be added to theoretical curves in certain cases to obtain a closer approach to the actual loading at the tip. The analysis indicated that the need for a tip correction decreases as either the aspect ratio or the wing taper is increased. In general, it may be said that, for wings of conventional aspect ratio, corrections to the theoretical span load curves are necessary only if the wing is tapered less than 2:1 and has a blunt tip. If the tip is well rounded in plan form, no correction appears necessary even for a wing with no taper.

Aerodynamic force tests of a Clark Y wing equipped with "Maxwell" type leading-edge slots were conducted in the N.A.C.A. 7- by 10-foot tunnel to ascertain the aerodynamic characteristics, which involved the determination of the best slot-gap opening, the effects of slat width, and the effect of a trailing-edge flap. The Maxwell wing with a wide-chord slat (0.30 c(sub w)) and with a 0.211 c(sub w) split flap deflected 60 degrees had a C(sub L sub max) of 2.53 or about twice that of the plain wing. The wing with the wide slat also had, in general, improved aerodynamic characteristics over those of the Maxwell wing with slat, and had about the same aerodynamic characteristics as a Handley Page slotted wing with approximately the same size of slat.

In this report charts are given showing the relation between time, velocities, and altitude for airplanes having various terminal velocities diving in a standard atmosphere. The range of starting altitudes is from 8,000 to 32,000 feet, and the terminal velocities vary from 150 to 550 miles per hour. A comparison is made between an experimental case and the results obtained from the charts. Examples pointing out the use of the charts are included.

"The principles of the Cross method of moment distribution are used to check the stability of structural members under axial load. A brief theoretical treatment of the subject, together with an illustrative problem, is included as well as a discussion of the reduced modulus at high stresses and a set of tables to aid in the solution of practical problems" (p. 1).

"The effect of tapered ailerons on linearly tapered wings is theoretically determined. Four different aileron spans are considered for each of three wing aspect ratios and each of four wing taper ratios. The change in lift on one half of the wing, the rolling moment, the additional induced drag, and the yawing moment, due to aileron deflection, are represented by non dimensional coefficients" (p. 1).

"The hydrodynamic characteristics of a model of the hull of the Short Calcutta (N.A.C.A. Model 47) are presented in non-dimensional form. This model represents one of a series of hulls of successful foreign and domestic flying boats the characteristics of which are being obtained under similar test conditions in the N.A.C.A. tank. The take-off distance and time for a flying boat having the hull of the Calcutta are compared at two values of the gross load with the corresponding distances and times for the same flying boat having hulls of two representative American types, the Sikorsky S-40 and the N.A.C.A. 11-A" (p. 1).

A series of tests was made in which the column strength of 17ST tubing was increased as much as 50 percent by prestressing the tubing to 40,000 pounds per square inch in compression under conditions of support that prevented column failure at this stress. This prestressing achieves it's beneficial effects entirely by improving the compressive properties of the material, principally the proportional limit.

"Curves of forced frequency against amplitude are presented for the conditions where the forced frequency is both increased and decreased into the resonant range. On the basis of these curves it is shown that the practical resonance frequency is the point where wrinkling first occurs and that the resonance frequency will be subject to considerable travel once permanent wrinkles appear in the vibrating shell. The decreasing mode of striking resonance is found to be by far the most destructive condition" (p. 1).

A series of tests was made at the National Advisory Committee for Aeronautics (NACA) free-spinning tunnel to determine the effect of systematic changes in wing and tail arrangement upon steady-spinning and recovery characteristics of a conventional low-wing monoplane model for a basic loading condition. Eight wings and three tails, covering a wide range of aerodynamic characteristics, were independently ballasted so as to be interchangeable with no change in mass distribution. For each of the 24 wing-tail combinations, observations were made of steady spins for four control settings and of recoveries for five control manipulators. The results are presented in the form of charts comparing the spin characteristics. The results showed that, with a poor tail arrangement, wing plan form and tip shape had a considerable effect on the spinning characteristics.

"This paper is essentially a consideration of mass balance of ailerons from a preliminary design standpoint, in which the extra weight of the mass counterbalance is the most important phase of the problem. Equations are developed for the required balance weight for a simple aileron and this weight is correlated with the mass-balance coefficient. It is concluded the location of the c.g. of the basic aileron is of paramount importance and that complete mass balance imposes no great weight penalty if the aileron is designed to have its c.g. inherently near to the hinge axis" (p. 1).

Pressure-distribution tests were conducted in the full-scale wind tunnel on a 2:1 tapered U.S.A. 45 airfoil equipped with 20 percent chord split trailing-edge flaps of various spans. A special installation was employed in the tests utilizing a half-span airfoil mounted vertically above a reflection plane. The airfoil has a constant chord center section and rounded tips and is tapered in thickness from 18 percent c at the root to 9 percent c at the tip. The aerodynamic characteristics, given by the usual dimension less coefficients, are presented graphically as functions of flap span and angle of attack as well as by semispan load diagrams. The results indicate, in general, that only a relatively small increase in the normal-force coefficient is to be expected by extending the flap span of an airfoil-flap combination, similar to the one tested, beyond 70 percent of the wing span.

"An investigation was made to determine the effect of variations in the horizontal and vertical air-entry angles on the performance characteristics of a single-cylinder 2-stroke-cycle compression-ignition test engine. Performance data were obtained over a wide range of engine speed, scavenging pressure, fuel quantity, and injection advance angle with the optimum guide vanes. Friction and blower-power curves are included for calculating the indicated and net performances" (p. 1).

"An investigation was made in the N.A.C.A. 7 by 10 foot wind tunnel of the distribution of air pressure over one chord section of a Clark Y-H airfoil with a split flap. The results obtained are given in the form of diagrams showing the chordwise distribution of pressure on both airfoil and flap as plots of calculated aerodynamic coefficients for both airfoil and flap" (p. 1).

The purpose here is to consider the mechanical characteristics of reinforced phenol-formaldehyde resin as related to its use as structural material for aircraft. Data and graphs that have appeared in the literature are reproduced to illustrate the comparative behavior of plastics and materials commonly used in aircraft construction. Materials are characterized as to density, static strength, modulus of elasticity, resistance to long-time loading, strength under repeated impact, energy absorption, corrosion resistance, and ease of fabrication.

"The N.A.C.A. has developed a simple pressure-level meter for the measurement of sound-pressure levels above 70 db. The instrument employs a carbon microphone but has no amplification. The source of power is five flashlight batteries. Measurements may be made up to the threshold of feeling with an accuracy of plus or minus 2 db; band analysis of complex spectra may be made if desired" (p. 1).

Report presenting a study of eight wings and three tails covering a wide range of aerodynamic characteristics in 24 wing-tail combinations. Observations were made of the steady spin for four control settings and of recoveries for five control manipulations. The effect of wing shape, tail arrangement, control settings, relationships between spin characteristics, and comparison with results for basic loading are provided.