Abstract: This technical report contains a description of the nuclear analysis performed upon the SM-2 core and vessel for the period September 1, 1958 to December 31, 1959. Calculations are given for core reactivity, power distributions, lifetime, reactor control, kinetics, radiation problems, fuel and poison burn-ups, and the nuclear effects of poisons, temperature, and geometry. Wherever possible, experimental data is included in order to test the validity of the analytical models. The SM-2 nuclear analysis was performed by Alco Products, in. under Tasks 1, 8, and 10 of Contract No. AT(30-2)-326 for the Atomic Energy Commission.

Abstract: An analysis of SM-1 Core II and SM-1A Core I zero power experiments was made by comparing these cores to each other and to AM-1 Core I on the basis of critical bank positions, bank calibrations and available chemical analyses of the fuel plate compositions. The effects of replacing boron absorbers by europium absorbers upon rod worth and stuck rod conditions were studied. Comparisons of measured and calculated power distributions were made. It was concluded that both SM-1 Core II and SM-1A Core I contain nearly identical B-10 loading of 17.79 grams, compared to the best estimate of 15.75 grams for SM-1 Core I. The available data indicates that all three cores possess similar nuclear characteristics.

Abstract; The fission product data obtained during SM-1 Core I operation (June 1957 - May 1960) is reviewed briefly and interpreted. Evidence is presented to indicate that a fuel element defect was responsible for the high fission product activity level observed in the primary coolant. Relative escape coefficients are calculated and the defect size estimated. Anticipated fission product levels during SM-1 Core II and SM-1A Core I operation are estimated from alpha surface contamination data on completed fuel elements. The importance of in-line sampling for monitoring fission product activity is stressed as well as the need for failed fuel element detection methods.

Abstract: Test procedures for special tests involving in-core SM-1 temperature and flow instrumentation are described (Task XIV Package Tests). These tests involve in-core steady state flow and temperature measurements, loss of flow transients, load transients, reduced primary system pressure operations and reduced element flow. The thermal and hydraulic conditions prevailing in these tests, including steady state and transient burnout rations, are developed. The effects of reduced system pressure and flow on the burnout ratios are determined as are the expected stuck rod conditions when Task XIV test elements are installed. The effect on the maximum credible accident is included and a recommendation to conduct these Task XIV package tests is made.

Abstract: This technical report describes the changes incurred in the SM-1 by the insertion of the SM-1 Core II and special components. The special components consist of impact specimens, a boron gradient rod, SM-2 elements, a PM-1-M element, and high burnup SM-1 Core I elements. The change in hazards, due to operation of SM-1 with Core II and the special components is evaluated. The analysis indicates there is no change in hazards.

Abstract: This technical report describes the Martin Co. PM-1-M-2 test element and analyzes the potential hazard incurred by its inclusion in the SM-1 Core II. A nuclear analysis develops power distributions and reactivity effects. Hydraulic and thermal analyses develop anticipated burnout heat flux ratios. An evaluation of the risk involved with the inclusion of this element is presented. In view of the narrow margin by which the PM-1-M-2 test element meets the minimum burnout ratios as defined by Alco Products, Inc., it is recommended that if time permits that critical facility design verification be accomplished. The PM-1-M-2 test element meets the minimum requirements for insertion in SM-1 Core II and in view of the importance of this element to the PM-1 and PM-3A program, should be considered for insertion.

Abstract: The removal of both SM-1 Core I high burnup elements from SM-1 Core II and the insertion of the PM-1-M-2 element and the SM-1 Core I spare element in SM-1 Core II is discussed. Nuclear and thermal characteristics of Core II with these changes are presented and conclusions related to the changes in the hazard potential are made. If the core change indicated by this report is made, local peaking factors will be decreased and burnout ratios will be increased. This, of course, in itself leads to a more conservative estimate of core safety. There is no conceivable reason why the perturbation may not be safely made in the SM-1 Core II.

Abstract: In the March-April 1962 shutdown of SM-1 Core II, the SM-28 element will be re-inserted in SM-1 Core II and an SM-1 Core I element will be removed. An SM-1 Core II europium absorber will be replaced by a Ag-Cd-In absorber, and surveillance specimens will be inserted above the core support structure. Analysis of these changes concludes that re-insertion of the SM-2B stationary element and insertion of surveillance specimens do not affect hazards potential previously defined for SM-1. Replacement of the europium absorber by the Ag-Cd-In absorber will have negligible effect on reactivity control worth of the rod. The absorber meat section is encapsulated to prevent exposure of silver alloy to the primary coolant; postulated release of silver due to a cladding defect, after 2 years irradiation in SM-1, would not cause a hazard such as to restrict access to the vapor container. Possibility of steam formation in the air gap between the absorber core and cladding, causing a cladding failure, is remote. Deformation of the absorber section sufficient to cause the rod to stick, would not impair the ability of the other rods to shut down the reactor safely.

Abstract: This preliminary technical report covers design of the SM Type 3 element, its use .in.. SM-1 Core III, and planned use in the Type 3 Core for PM-2A. The Type:3 element characteristics are compared with Type 1 (SM-1 Core I) element nuclear, metallurgical, thermal and hydraulic characteristics and fabrication. The effect of using the Type 3 element in SM-1 Core III and. its planned use in a Type 3 Core for PM-2A is discussed with regard to operation, shielding, reactor safety and all conceivable special problems.

Abstract: The natural circulation, direct cycle, boiling water reactor reference design presented in this technical report is the alternate to the preferred preliminary design developed under Phase I of the PL-3 contract. The report presents plant design criteria, summary of plant selection, plant description, reactor and primary system description, thermal and hydraulic analysis, nuclear analysis, control and instrumentation description, shielding description, auxiliary systems, power plant equipment, waste disposal, buildings and tunnels, services, operation and maintenance, logistics, erection, cost information and training program outline.

Abstract: The pressurized water reactor preliminary design presented in this volume is the preferred design developed under Phase I of the PL-3 contact. This technical report presents plant design criteria, summary of plant selection, plant description, reactor and primary system description, thermal and hydraulic analysis, nuclear analysis, control and instrumentation description, shielding description, auxiliary systems, power plant equipment, waste disposal, buildings and tunnels, services, operation and maintenance, logistics, erection, cost information and a training program outline.

Abstract: This technical report summarizes the results of research and development tasks performed during Phase I of this contract and presents recommendations for future development work. Work is reported in the areas of plant assembly and relocation, housings and footings, waste heat dissipation, instrumentation, refueling systems, waste disposal, shielding, core nuclear thermal and hydraulic studies, gaseous waste processing (BWR), and critical experiments on a 5 x 5 array of Type 3 fuel elements.

Abstract: This technical report covers development of an AG-Cd-In alternate absorber section for Army Type SM reactors. It describes the absorber material composition and the geometric configuration. It gives the nuclear and thermal analyses supporting this configuration and a detailed description of the manufacturing practice employed in fabricating the final design component.

Abstract: The most adverse power distribution and power peaking factors have been developed for Type 3 replacement cores for SM-1, SM-1A, and PM-2A. Also included is the 37 element Type 3 core for SM-1, which is known as SM-1 Core III and is a prototype of a Type 3 core for PM-2A. The power distributions were compared with measured distributions obtained on type 3 fuel elements in SM-1, SM-1A and PM-2A core configurations. Using the measured data as a standard, correction factors were obtained and applied to the analytical predictions of the most adverse power distribution.

Abstract: This technical report describes the changes incurred in the PM-2A by the planned insertion of PM-2A Core II and the replacement of the startup and check sources. PM-2A Core II components were fabricated to specifications very nearly identical to those of PM-2A Core I. The essential difference in the cores is the boron loading which permits PM-2A Core II to meet a "one-stuck rod criteria" at beginning of life. This core has been subjected to a zero power experiment and loading procedures have been developed at the Alco Critical Facility. The nuclear and thermal and hydraulic characteristics are essentially identical to those of Core I and the replacement of the startup and check sources represent no increase in the potential for or magnitude of a hazardous situation.

Abstract: A cyclic stress analysis of the SM-1 primary system was carried out. Problems encountered in the fabrication of PM-2A Core II and SM-lA Core II are described, and the results of an examination of damaged SM-lA Core I stationary fuel elements reported. A preliminary study of the radiation damage to SM-1 reactor vessel was made and the possibility of annealing the vessel discussed. Performance analyses are presented for five cores: SM-1 Core, SM-1 Core 1 rearranged and spiked, SM-1 Core II with special components, PM-2A Core 1, and SM- 1A Core 1. Preliminary critical experiments were made with SM-2 elements in a SM- 1 core configuration and nuclear and thermal analyses of the use of SM-2 elements in SM-1, SM-1A, and PM-2A completed. A throttling steam calorimeter was selected for measuring moisture carry-over on the PM-2A steam generator. Test procedures for evaluating the shielding of the SM-1, SM-lA, and PM-2A plants are summarized. Radiochemical and chemical analyses of SM-1 coolant and crud are summarized, and methods of activity control discussed. Preliminary results of studies of the properties of reactor pressure vessels under irradiation and no irradiation conditions are summarized briefly.

Abstract; SM-1 Reactor Core I Rearranged and Spiked, and Core II with Special Components were analyzed under various off-design conditions to induce nucleate boiling. The steady state code, STDY-3, written for the thermal analysis of pressurized water cores, was employed for the analysis. The code performs a complete steady state parallel channel thermal analysis for both nominal and hot channels. Thermal characteristics of individual elements were investigated while changing the parameters of primary pressure or inlet temperature to introduce the phenomenon of nucleate boiling in the the core. Reduction of system pressures to 1000, 800, and 600 psia and increasing core inlet temperatures to 465 and 500 degree F were studied as the means to induce boiling in the core. This analysis indicates that SM-1 Core I Rearranged and Spiked can be safely operated at the reduced pressure of 910 psia without introducing extensive boiling in the core. SM-1 Core II with Special Components can be operated at 800 psia or at an inlet temperature of 500 degree F at 1200 psia.

Abstract: Thermal characteristics of the SM-2 core were analyzed at steady state and loss of flow conditions. For steady state operation, the steady state code STDY-3 was used. For transients during a loss of flow accident, ART-02, a one-dimensional code, was used. This analysis indicates the SM-2 core is safe from burnout under steady state operation at design power level (28 tMW) because (1) no nucleate boiling exists, and (2) the minimum burnout ratio is above 2.0. The core is safe from burnout under loss of flow transient because the minimum burnout ratio in the hottest element channel of 1. 82 is above the minimum design criteria of 1. 5.

Abstract: A detailed description of the PM-2A reactor, primary system and instrumentation is presented. A general description of the secondary system and plant arrangement at Camp Century, Greenland is included. The results of the startup physics, shielding, thermal and hydraulics and radiochemistry test are presented. the analysis performed on the shielding and thermal and hydraulic tests is included. The shielding problem at startup and the shielding modification made to the plant are described along with the radiation measurements made in these areas.

Abstract: This technical report presents design criteria to prevent the brittle fracture of ferritic reactor vessels that cold occur as a result of the rise in NDT caused by fast neutron irradiation. The criteria require that maximum principal stress in the vessel does not exceed 18 percent of yield stress at temperatures below NDT + 60 degree F. Under certain conditions the allowable stress may be based on the irradiated yield stress. A discussion of brittle fracture and an explanation of the criteria are included.

Abstract: This technical report contains the description and results of an experimental program to evaluate the effect of utilizing Type 3 (SM-2) replacement cores in existing Army field plants SM-1, SM-1A and PM-2A. This program, conducted at the Alco Products Critical Facility, employed SM-2 mockup fuel elements similar in composition to Type 3 fuel elements to determine start-up characteristics of Type 3 cores in SM-1, SM-1A and PM-2A core configurations. measurements include comprehensive power distribution, temperature coefficients, initial critical bank positions, control rod calibrations, critical rod configuration and material coefficients, all obtained under cold, clean, core conditions. The 45 element SM-1 and SM-1A configuration with SM-2 mockup fuel elements contain 36.4 Kg U-235 and an estimated 67.9 gm B-10, while the 37 element PM-2A configuration with SM-2 mockup elements contains 30.0 Kb U-235 and an estimated 56 gm B-10.

Abstract: This technical report elucidates principles of hazards evaluation. The concept of hazards potential is introduced and utilized to show how a reactor system perturbation will influence its nuclear safety. Literature relating to reactor safety is referenced to provide the sources of information required for hazards analysis and show how they influence a hazards evaluation. A checklist of items which should be considered in evaluating a change, test, or modification is presented.

Abstract: This report presents metallurgical .analyses and corrosion tests conducted to determine :causes of failure of two SM- 1 reactor vessel studs due to fracture in the threaded areas, after 23 months' operation (March 1959). Conclusions of corrosion tests are: (1) failure of the studs was caused by stress corrosion cracking, (2) contributing factors to failure of the studs were improper control of heat treatment of the studs and absence of treatment for stress relief after thread grinding operation.

Abstract: Progress is reported on research and development tasks under the Program Plan for Engineering Support and Development of Army Pressurized Water Reactor Power Plants, Contract AT(30-1)-2639, during the six months' period October 1, 1061 to March 31, 1962.