"A resume of the equations and formulas for the forces and moments on an aircraft-engine mount is presented. In addition, available experimental data have been included to permit the computation of these forces and moments. A sample calculation is made and compared with present design conditions for engine mounts" (p. 1).

"It is shown that the control force of ordinary ailerons may be reduced to zero over a range of deflections and at a given flight condition by the use of an appropriate differential movement. Approximations to the ideal motion obtainable with a simple linkage are discussed and a chart that enables the selection of an appropriate crank arrangement is presented. Various aspects of the practical application of the system are discussed and it is concluded that a small fixed tab, deflected to trim both ailerons upward, would be advantageous" (p. 1).

"Flight tests of a Grumman Scout (XSF-2) airplane fitted with a Pratt & Whitney 1535 supercharged engine were conducted to determine the effect of engine power, mass flow of the cooling air, and atmospheric temperature on cylinder temperature. The tests indicated that the difference in temperature between the cylinder wall and the cooling air varied as the 0.38 power of the brake horsepower for a constant mass flow of cooling air, cooling-air temperature, engine speed, and brake fuel consumption. The difference in temperature was also found to vary inversely as the 0.39 power of the mass flow for points on the head and the 0.35 power for points on the barrel, provided that engine power, engine speed, brake fuel consumption, and cooling-air temperature were kept constant" (p. 1).

"The development of metal construction for aircraft has created a need for accurate and detailed information regarding the strength of riveted joints in aluminum-alloy structures. To obtain this information the National Bureau of Standards in cooperation with the National Advisory Committee for Aeronautics is investigating the strength of riveted joints in aluminum alloys. The strength of riveted joints may be influenced by the form of the head, the ratio of the rivet diameter to the sheet thickness, the driving stress, and other factors" (p. 1).

From Introduction: "The possibilities of the jump take-off have been established by some full-scale experiments. It is the purpose of this paper to study the factors that govern the jump take-off in its simplest form and to present the results of model tests in which the effect of differences in the rotor parameters was determined."

"The distribution of the fuel among the various cylinders of a Pratt and Whitney 1340 S1H1-G engine was determined by chemically analyzing samples of exhaust gas from each cylinder. The engine was operated in the 20-foot wind tunnel at different power outputs, specific fuel consumptions, and engine speeds. The results showed that the variation in the quality of the mixture among the different cylinders was approximately 4 percent and was independent of power output, specific fuel consumption, and engine speed. The results also showed that the top cylinders operated with a lower air-fuel ratio than the bottom cylinders" (p. 1).

"Charts are presented for determining the performance of airplanes having variable-pitch propellers, the pitch of which is assumed to be adjusted to maintain constant speed for all rates of flight. The charts are based on the general performance equations developed by Oswald in reference 1, and are used in a similar manner. Examples applying the charts to airplanes having both supercharged and unsupercharged engines are included" (p. 1).

A general test was made in the N.A.C.A. tank of a 1/12-size model of the hull of the British Singapore IIC flying boat loaned by the Director of Research, British Air Ministry. The results are given in charts and are compared with the results of tests of a model of an American flying-boat hull, the Sikorsky S-40. The Singapore hull has a greater hump resistance but a much lower high-speed resistance than the S-40.

An analysis of the factors governing the oscillation of an autogiro rotor blade in the plane of the rotor disk showed that the contribution of the air forces to the resultant motion was small and that the oscillation is essentially a direct effect of the rotor-blade flapping motion. A comparison of calculated oscillations with those measured in flight on three different rotors disclosed that the calculations gave satisfactory agreement with experiment. The calculated air forces on the rotor blade appear to be larger than the experimental ones, but this discrepancy can be attributed to the deficiencies in the strip analysis.

"The cost in mean effective pressure of generating air flow in the combustion chambers of single-cylinder compression-ignition engines was determined for the prechamber and the displaced-piston types of combustion chamber. For each type a wide range of air-flow quantities, speeds, and boost pressures was investigated. Supplementary tests were made to determine the effect of lubricating-oil temperature, cooling-water temperature, and compression ratio on the friction mean effective pressure of the single-cylinder test engine" (p. 1).

"Full-scale wind-tunnel and flight tests were made of a Fairchild 22 airplane equipped with a Fowler flap to determine the effect of the flap on the performance and control characteristics of the airplane. In the wind-tunnel tests of the airplane with the horizontal tail surfaces removed, the flap was found to increase the maximum lift coefficient from 1.27 to 2.41. In the flight test, the flap was found to decrease the minimum speed from 58.8 to 44.4 miles per hour" (p. 1).

A model of the hull of the Navy PB-1 flying boat was tested in the N.A.C.A. tank as part of a program intended to provide information regarding the water performance of hulls of flying boats of earlier design for which hydrodynamic data have heretofore been unavailable. Tests were made according to the general method over the range of practical loadings with the model both fixed in trim and free to trim. A free-to-trim test according to the specific method was also made for the design load and take-off speed corresponding to those of the full-scale flying boat. The resistance obtained from the fixed-trim test was found to be about the same as that of the model of the NC flying-boat hull, and greater at the hump but smaller at high speeds than that of a model of the Sikorsky S-40 flying-boat hull.

Several improvements that have been made on commercially available carbon-monoxide indicators to make them more suitable for aircraft use are described. These improvements include an automatic flow regulator, which permits the use of a simplified instrument on aircraft where a source of suction is available, and a more reliable alarm attachment. A field method for testing instruments on standard samples of carbon monoxide is described. Performance data and instructions in operation and maintenance are given.

"A method of determining the moments of inertia of an airplane from design data pertaining to the weights and locations of the component parts is described. The computations required to ascertain the center-of-gravity position are incorporated with the calculations of moments of inertia. A complete set of data and calculations for a modern airplane is given to illustrate the procedure. From a comparison between calculated values and measured values it is believed that the moments of inertia can be estimated within 10 percent by the use of this method" (p. 1).

"An investigation was made to obtain information on the minimum quantity of air and power required to cool conventional air cooled cylinders at various operating conditions when using a blower. The results of these tests show that the minimum power required for satisfactory cooling with an overall blower efficiency of 100 percent varied from 2 to 6 percent of the engine power depending on the operating conditions. The shape of the jacket had a large effect on the cylinder temperatures. Increasing the air speed over the front of the cylinder by keeping the greater part of the circumference of the cylinder covered by the jacket reduced the temperatures over the entire cylinder" (p. 1).

Four models with longitudinal steps on the forebody were developed by modification of a model of a conventional hull and were tested in the National Advisory Committee for Aeronautics (NACA) tank. Models with longitudinal steps were found to have smaller resistance at high speed and greater resistance at low speed than the parent model that had the same afterbody but a conventional V-section forebody. The models with a single longitudinal step had better performance at hump speed and as low high-speed resistance except at very light loads. Spray strips at angles from 0 degrees to 45 degrees to the horizontal were fitted at the longitudinal steps and at the chine on one of the two step models having two longitudinal steps. The resistance and the height of the spray were less with each of the spray strips than without; the most favorable angle was found to lie between 15 degrees and 30 degrees.

"An approximate empirical criterion, based on the projected side area and the mass distribution of the airplane, was formulated. The British results were analyzed and applied to American designs. A simpler design criterion, based solely on the type and the dimensions of the tail, was developed; it is useful in a rapid estimation of whether a new design is likely to comply with the minimum requirements for safety in spinning" (p. 1).

"A series of tests was made in the N.A.C.A. free spinning tunnel to find the effect upon spinning characteristics of systematic changes in tail arrangement. The tests were made with a 1/16-scale made of a low-wing monoplane of modern design. The changes consisted of: (1) variation of the fuselage length; (2) variation of the fore-and-aft location of the vertical surfaces; and (3) variation of the vertical location of the horizontal surfaces. The spinning characteristics of the model, including the number of turns required for recovery, were found to vary systematically and regularly with systematic changes in the tail arrangement" (p. 1).

An empirical method is given for estimating the aerodynamic effect of ordinary and split flaps on airfoils similar to the Clark Y. The method is based on a series of charts that have been derived from an analysis of existing wind-tunnel data. Factors are included by which such variables as flap location, flap span, wing aspect ratio, and wing taper may be taken into account. A series of comparisons indicate that the method would be suitable for use in making preliminary performance calculations and in structural design.

From Summary: "Performance tests were made using a rectangular displacer arranged so that the combustion air was forced through equal passages at either end of the displacer into the vertical-disk combustion chamber of a single-cylinder, four-stroke-cycle compression-ignition test engine. After making tests to determine optimum displacer height, shape, and fuel-spray arrangement, engine-performance tests were made at 1,500 and 2,000 r.p.m. for a range of boost pressures from 0 to 20 inches of mercury and for maximum cylinder pressures up to 1,150 pounds per square inch. The engine operation for boosted conditions was very smooth, there being no combustion shock even at the highest maximum cylinder pressures. Indicated mean effective pressures of 240 pounds per square inch for fuel consumptions of 0.39 pound per horsepower-hour have been readily reproduced during routine testing at 2,000 r.p.m. at a boost pressure of 20 inches of mercury."

"In order to determine whether or not flaps could be expected to have any beneficial effect on take-off performance, the distances required to take off and climb to an altitude of 50 feet were calculated for hypothetical airplanes, corresponding to relatively high-speed types and equipped with several types of flap. The types considered are the Fowler wing, the Hall wing, the split flap, the balanced split flap, the plain flap, and the external-airfoil flap. The results indicate that substantial reductions in take-off distance are possible through the use of flaps, provided that the proper flap angle corresponding to a given set of conditions is used" (p. 1).

"A 1/7.06 full-size model of the NC-type hull was tested in the N.A.C.A. tank by both the general method and the specific or free-to-trim method. The results of the tests are given in curves plotted as non dimensional coefficients and are compared with the test results of N.A.C.A. model 11-A. The NC model (N.A.C.A. model 44) shows higher resistance than model 11-A at hump speed but lower resistance at high speeds. Model 44 has a higher best trim angle at the jump and a lower maximum positive trimming moment than model 11-A. At high speeds the best trim angle and the trimming moments of the two models are approximately the same" (p. 1).

The results of tests of six airfoils having the N.A.C.A. 230 mean line and varying in thickness from 0.06c to 0.21c are presented. These results agree with previous findings in showing that aerodynamically the best section is one of moderate thickness. The data are of value mainly in connection with the design of tapered wings having sections based on the N.A.C.A. 230 mean line.

Note presenting the influence of fuel-oil temperature on combustion as investigated by injecting the fuel into the prechamber of a single-cylinder, 4-stroke-cycle, water-cooled, compression-ignition engine operating at 1500 rpm and at a compression ratio of 13.5. The results showed that heating the fuel oil to 750 degrees Fahrenheit increased the injection period, changed the rate of injection, and eliminated the spray cone.