A balanced diaphragm type of maximum cylinder pressure indicator was designed to give results consistent with engine operating conditions. The apparatus consists of a pressure element, a source of controlled high pressure and a neon lamp circuit. The pressure element, which is very compact, permits location of the diaphragm within 1/8 inch of the combustion chamber walls without water cooling. The neon lamp circuit used for indicating contact between the diaphragm and support facilitates the use of the apparatus with multicylinder engines.

This report describes a model water tunnel built in 1928 by the NACA to investigate the possibility of using water tunnels for aerodynamic investigations at large scales. The model tunnel is similar to an open-throat wind tunnel, but uses water for the working fluid.

Study of the bending stress in smooth skin, aluminum alloy, true monocoque fuselage sections of varying ratio of diameter to thickness.

The tests herein reported were conducted by the NACA to determine the effect of the angular position of the section of a ring cowling on the speed of an airplane having a radial air-cooled engine.

The tests, conducted at the Guggenheim Aeronautical Laboratory of Stanford University, to investigate the phenomenon of separation in the air flow past geometric shapes are described in this report.

"The penetration and cone-angle of fuel sprays from open nozzles were recorded with the NACA Spray Photography Equipment. The results show that for injection systems in which the rate of pressure rise at the discharge orifice is high, open nozzles give spray-tip velocities and penetrations which compare favorably with those of closed nozzles. The spray cone-angle was the same for all tests, although open nozzles having different orifice diameters were used, and one nozzle was used both as an open and as a closed nozzle" (p. 1).

From Summary: "This note contains a description of an improved apparatus and procedure used by the NACA for determining the moments of inertia of airplanes. The method used, based on the pendulum theory, is similar to that previously used, but a recent investigation of its accuracy has resulted in the improvements described herein. The error, when using the new apparatus and procedure, has been found to be of the order of 1 per cent."

From Summary: "This report presents a theoretical analysis of the lift on a trailing edge flap. An analytical expression has been derived which enables the computation of the flap load coefficient. The theoretical results seem to show a fair agreement with the meager experimental results which are available."

"The effect of variations of orifice length to diameter ratio on spray characteristics was determined for a 0.014-inch and a 0.040-inch orifice for ratio of 0.5 to 4.0. The nozzles containing the orifices were mounted in an injection valve and tested with a plan stem and with a helically grooved stem. The injection pressure was varied from 4000 to 8000 pounds per square inch. The air density into which the fuel was sprayed was varied from the density obtained with a pressure of 60 pounds per square inch to the density obtained with a pressure of 250 pounds per square inch at room temperature" (p. 1).

The survey of the possibilities for distinguishing between plain carbon and chromium-molybdenum steel tubing included the Herbert pendulum hardness, magnetic, sparks, and chemical tests. The Herbert pendulum test has the disadvantages of all hardness tests in being limited to factory use and being applicable only to scale-free, normalized material. The small difference in the range of hardness values between plain carbon and chromium-molybdenum steels is likewise a disadvantage.

"The 'Farnboro' electric indicator was tested as received from the manufacturers, and modifications made to the instrument to improve its operation. The original design of disk valve was altered so as to reduce the mass, travel, and seat area. Changes were made to the recording mechanism, which included a new method of locating the top center position on the record. The effect of friction on the motion of the pointer while taking motoring and power cards was eliminated by providing a means of putting pressure lines on the record" (p. 1).

"This paper describes an investigation on airplane landing speeds which was made to determine the applicability of accepted aerodynamic theory to the prediction of this particular performance characteristic. The experimental work consisted in measuring the landing speed of several monoplanes by a new photographic method. The results of these tests supplemented by available information regarding biplanes were compared with predictions made with basic aerodynamic theory" (p. 1).

"This note presents the results obtained in pressure distribution tests on the right upper wing panel and tip of a Douglas M-3 airplane in flight. These tests are a part of a more extensive investigation of the effect of changes in tip shape on the load distribution, the tip reported herein being the first of a series of tip shapes being tested. The results are given in tables and curves in such form that the load distribution for any conditions may be determined easily. Tests were made at Langley Field by the NACA in the spring of 1930" (p. 1).

A review of various methods to prevent ice formation and adhesion to aircraft surfaces is given. It was concluded that the adhesion of ice to a surface may be reduced somewhat by the application of certain waxes and varnishes. In the experiments described, the varnishes containing calcium stearate and calcium oleate gave the best results. In wind tunnel tests, the adhesion was further reduced by the application of these waxes and varnishes to a thin, heat insulating layer of rubber.

The results presented in this note show the effect of twist and sweepback on the span load distribution over two monoplane wing models. The tests were made in the Atmospheric Wind Tunnel of the Langley Memorial Aeronautical Laboratory. The data are taken from the results of an investigation dealing primarily with lateral stability. As presented, they are suitable as an aid in the structural design of certain monoplane wings.

"Tests on a Friez type cup anemometer have been made in the variable density wind tunnel of the Langley Memorial Aeronautical Laboratory to calibrate the instrument and to determine its suitability for velocity measurements of wind gusts. The instrument was calibrated against a Pitot-static tube placed directly above the anemometer at air densities corresponding to sea level, and to an altitude of approximately 6000 feet. Air-speed acceleration tests were made to determine the lag in the instrument reading. The calibration results indicate that there should be an altitude correction. It is concluded that the cup anemometer is too sluggish for velocity measurements of wind gusts" (p. 1).

A large number of tests were made on tubes of 1025 and 4130X steel, in various diameters and wall thicknesses, and after diverse heat treatments. The Rockwell B scale was employed, as being the best suited to the ranges of hardness encountered. Only satisfactory chrome molybdenum tubes were found to show a hardness in excess of 90-B after normalizing.

Seamless steel tubing is today the principal material of construction for aircraft. The commercial grade of tubing containing about 0.10 to 0.20% carbon at first used is being superseded by two grades which are approved by the army and navy, and which are also becoming standard for commercial airplanes.

This report presents test results obtained at the Langley Memorial Aeronautical Laboratory of the National Advisory Committee for Aeronautics during an investigation to determine the relative performance of a single-cylinder, high-speed, compression-ignition engine when using fuel injection valve nozzles with different numbers, sizes, and directions of round orifices. A spring-loaded, automatic injection valve was used, centrally located at the top of a vertical disk-type combustion chamber formed between horizontally opposed inlet and exhaust valves of a 5 inch by 7 inch engine.

"This note is on an investigation made to obtain information on the strength of thin curved sheets of Alclad in shear. Designers may utilize this material as a strength member as well as for a covering for the wings and fuselages. A reduction may then be made in the size of the internal strength members. These experiments were undertaken with the object of securing the maximum value from the metal in this respect" (p. 1).

"The drag due to the various parts of a Fairchild (FC-2W2) cabin monoplane was measured at air speeds varying from 50 to 100 m.p.h., in the Twenty-Foot Propeller Research Tunnel of the National Advisory Committee for Aeronautics. It was found that the largest drag was due to the radial air-cooled engine. The measured drag due to the landing gear was also large, being about 4/5 of that due to the engine" (p. 1).

"This investigation was conducted to determine the effectiveness of various surface coatings as a means for preventing ice formations on aircraft in flight. The substances used as coatings for these tests are divided into two groups: compounds soluble in water, and those which are insoluble in water. It was found that certain soluble compounds were apparently effective in preventing the formation of ice on an airfoil model, while all insoluble compounds which were tested were found to be ineffective" (p. 1).

Presented here are experimental results obtained from a brief investigation of the appearance, penetration, and dispersion of oil sprays injected into a chamber of highly heated air at atmospheric pressure. The development of single sprays injected into a chamber containing air at room temperature and at high temperature was recorded by spray photography equipment. A comparison of spray records showed that with the air at the higher temperature, the spray assumed the appearance of thin, transparent cloud, the greatest part of which rapidly disappeared from view. With the chamber air at room temperature, a compact spray with an opaque core was obtained. Measurements of the records showed a decrease in penetration and an increase in the dispersion of the spray injected into the heated air. No ignition of the fuel injected was observed or recorded until the spray particles came in contact with the much hotter walls of the chamber about 0.3 second after the start of injection.

Presented here are pressure distribution data obtained from the tail surfaces of a PW-9 in a number of flight maneuvers. The results given are part of those obtained in an extensive investigation of the pressure distribution over all of the lifting and control surfaces of this airplane. The results are given in tabular and curve form and are discussed briefly with respect to their comparison with existing tail surface design specifications. It is recommended that tail load design loadings should be revised upwards. This is particularly true of leading edge loads, which should be at least doubled for thick sections.