An investigation on the cowling of radial air-cooled engines was conducted in the 20-foot Propeller Research Tunnel at Langley Field. Cooling and drag tests were made with each form of cowling. The propulsive efficiency was found to be practically the same with all forms of cowling.

"The results of an investigation to determine the pressures in the open cockpit of a Vought VE-7 airplane are given. The information has been considered valuable on account of its possible effect upon the operation of instruments, particularly altimeters, due to a variation from the true static pressure which is induced by the passage of the airplane through the air. The observed values are small and the effect upon instruments is inconsiderable" (p. 1).

The purpose of this report is to correlate, bring up to date, and put under a single cover all the information thought to be essential to an understanding of the formulas regarding bearing strength of wood under steel aircraft bolts and washers and other factors influencing fitting design.

Tests were made to determine the effect of fillets between wings and fuselage on the drag and propulsive efficiency of a high-wing cabin monoplane. These tests were made in the 20-foot Propeller Research Tunnel of the National Advisory Committee for Aeronautics.

An investigation was conducted to determine the injection lag, duration of injection, and spray start and cut-off characteristics of a fuel injection system operated on an engine and injecting fuel into the atmosphere. The results indicated that for the injection system investigated, the injection lag, in crank degrees, decreased with increase in engine speed for a constant quantity of fuel discharged, but was not affected at constant engine speed by varying the fuel quantity from approximately one-half to full load fuel quantity.

This report is concerned with the importance of the flat-top lift curve as a factor contributing to safety and control at low speed. An analysis of existing airfoil data indicated definite relations between the shape of the lift curve and certain section dimensions. The shape of the lift curve at maximum lift appears to be of sufficient importance to justify additional investigation with the view of developing a section with satisfactory efficiency and moment characteristics.

A series of experiments made in the wind tunnel of the Daniel Guggenheim School of Aeronautics, New York University, on the effect of tip shields on a horizontal tail surface are described and discussed. It was found that some aerodynamic gain can be obtained by the use of tip shields though it is considered doubtful whether their use would be practical.

Force tests on a systematic series of wing systems over a range of angle of attack from minus forty-five degrees to plus ninety degrees are covered in this report. The investigation was made on monoplane and biplane wing models to determine the effects of variations of tip shape, aspect ratio, flap setting, stagger, gap, decalage, sweepback, and airfoil profile.

This note describes tests of the drag due to a Wright "Whirlwind" (J-5) radial air-cooled engine mounted on a cabin type airplane. The tests were made in the 20-foot Propeller Research Tunnel of the National Advisory Committee for Aeronautics. The drag was obtained with three different types of exhaust stacks: Short individual stacks, a circular cross section collector ring, and a streamline cross section collector ring.

In order to experimentally study the conditions leading to ice formation on aircraft surfaces, an aircraft was equipped with small auxiliary surfaces and aerodynamic shapes similar to struts, wires, Pitot heads, etc. This airplane was flown at an altitude where a temperature of 32 F was encountered, at such times as cloud formations could be found at the coincident altitude. Here it was discovered that ice formed rapidly in regard to quantity, character, shape, and rapidity of formation.

This report records observations and recommendations resulting from an inspection trip to representative aircraft manufacturing establishments and repair stations. This inspection was made for the Navy Department and was specifically in reference to gluing practice at the various places visited. The period of the visits was between November 23, 1926 and February 16, 1927.

"Biplane cellules using the N.A.C.A.-M6 airfoil section have been tested in the variable density wind tunnel of the National Advisory Committee for Aeronautics. Three cellules, differing only in the amount of stagger, were tested at two air densities, corresponding to pressures of one atmosphere and of twenty atmospheres. The range of angle of attack was from -2 degrees to +48 degrees. The effect of stagger on the lift and drag, and on the shielding effect of the upper wing by the lower at high angles of attack was determined" (p. 1).

A brief description is given of different groups of high chromium steels (rustless iron and stainless steels) according to their composition and more generally accepted names. The welding procedure for a given group will be much the same regardless of the slight variations in chemical composition which may exist within a certain group. Information is given for the tensile properties (yield point and ultimate strength) of metal sheets and welds before and after annealing on coupons one and one-half inches wide.

"A peculiar phenomena in seaplane landing is observed and reported. The seaplane having executed a normal fast landing at low incidence, a forward movement of the control stick effected an unusual condition in that the seaplane left the water suddenly in an abnormal attitude. The observations describing this phenomena are offered as a warning against possible accident and as a conjectural cause of seaplane landing accidents of a certain kind" (p. 1).

The tests described in this report constitute a preliminary investigation of airfoil boundary layer control, as carried out in the atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory, from February to August, 1927. Tests were made on a U.S.A. 27 airfoil section with various slot shapes and combinations, and at various amounts of pressure or suction on the slots. The lift of airfoils can be increased by removing or by accelerating the boundary layer. Removing the boundary layer by suction is more economical than to accelerate it by jet action. Gauze-covered suction slots apparently give the best results. When not in operation, all suction slots tested had a detrimental effect upon the aerodynamic characteristics of the airfoil which was not apparent with the backward-opening pressure slots. Thick, blunt-nose airfoils would seem to give best results with boundary layer control.

Tests were conducted to investigate the possibility of a serious accident arising from unintentional contact with the water in substantially horizontal flight at high speed. Referring to vector diagrams on Figure 2, it will be seen that a very dangerous condition may arise if the float be allowed to come in contact with the water at high speeds as, for example, when flying at high speed just above the water. The initial diving moment due to suction and drag combined may be great enough to cause the seaplane to nose under before the pilot is able to control the motion.

Since aircraft design is tending toward all-metal construction, the strong heat-treatable light aluminum alloy, duralumin (a generic name for a class of heat-treatable alloys containing Cu, Mg, Mn, and Si), is finding increasing application. Doubt has been expressed concerning the reliability and permanence of these materials. Information is given on the effect of corrosion on the tensile properties of 14-gauge sheet duralumin, heat treated by quenching in hot water after being heated for 15 minutes in a fused nitrate bath at 500 to 510 C. Intercrystalline corrosion and practical aspects of intercrystalline embrittlement are discussed with respect to duralumin.

The permanence, with respect to corrosion, of light aluminum alloy sheets of the duralumin type, that is, heat-treatable alloys containing Cu, Mg, Mn, and Si is discussed. Alloys of this type are subject to surface corrosion and corrosion of the interior by intercrystalline paths. Results are given of accelerated corrosion tests, tensile tests, the effect on corrosion of various alloying elements and heat treatments, electrical resistance measurements, and X-ray examinations.

As a result of testing, it was determined that control of the rate of quenching and the avoidance of accelerated aging by heating are the only means of modifying duralumin itself so as to minimize the intercrystalline form of corrosive attack. It is so simple a means that it should be adopted even though it may not completely prevent, but only reduce, this form of corrosive attack. By so doing, the need for protection of the surface is less urgent.

Although the corrosion resistance of sheet duralumin can be greatly improved by suitable heat treatment, protection of the surface is still necessary if long life under varied service conditions is to be insured. The coatings used for this purpose may be grouped into three classes: the varnish type of coating, the oxide type produced by a chemical treatment of the surface, and metallic coatings, of which aluminum appears to be the most promising. Since the necessary weather exposure tests are not complete, some of the conclusions regarding the value of various surface coatings are necessarily tentative.

The tests described in this paper afford a direct comparison of the efficiency and smoothness of flow obtained with propeller fan and multiblade centrifugal fan drives in the same wind tunnel. The propeller fan was found to be superior to the centrifugal fan in that the efficiency was about twice as great, and the flow much smoother.

Measurements of drag were made on fittings taken from a typical fuselage to determine whether the difference between the observed full size fuselage drag and model fuselage drag could be attributed to the effects of fittings and surface irregularities found on the full size fuselage and not on the model. There are wide variations in the drag coefficients for the different fittings. In general those which protrude little from the surface or are well streamlined show very low and almost negligible drag. The measurements show, however, that a large part of the difference between model and full scale test results may be attributed to these fittings.

"This note contains the results of tests to determine the resistance of four sizes of streamline wire. The investigation was conducted in the six-inch wind tunnel of the National Advisory Committee for Aeronautics. The tests were made at various velocities and it was found that the resistance of streamline wires was considerably less than that of round wires of equivalent strength. Scale effect was also found since, with an increase of Reynolds Number, a decrease in the resistance coefficient was obtained" (p. 1).

Described here is an automatic control that has been used in several forms in wind tunnels at the Washington Navy Yard. The form now in use with the 8-foot tunnel at the Navy Yard is considered here. Details of the design and operation of the automatic control system are given. Leads from a Pitot tube are joined to an inverted cup manometer located above a rheostat. When the sliding weight of this instrument is set to a given notch, say for 40 m.p.h, the beam tip vibrates between two electric contacts that feed the little motor. Thus, when the wind is too strong or too weak, the motor automatically throws the rheostat slide forward and backward. If it failed to function well, the operator would notice the effect on his meniscus, and would operate the hand control by merely pressing the switch.