"The investigation was made for the purpose of ascertaining the notch sensitivity of flat strips of light alloy with cylindrical holes under initial tension stress, with special attention to the change in notch-effect factors with the number of load cycles. Then the studies were extended to similar flat strips with pin-loaded holes (tension lugs). This report deals with fatigue tests under initial tension load on flat test specimens of 3116.5 duralumin and AZM 3510.1 electron with plain unloaded and pin-loaded holes (tension lugs) of different forms" (p. 1).

"A discussion is given of the behavior of the shock-absorbing system, consisting of elastic struts and tires, under landing, take-off, and taxying conditions, and a general formula derived for obtaining the minimum stroke required to satisfy the conditions imposed on the landing gear. Finally, the operation of some typical shock-absorbing systems are examined and the necessity brought out for taking into account, in dynamic landing-gear tests, the effect of the wing lift at the instant of contact with the ground" (p. 1).

"The torsion of box beams of rectangular section, the edges of which are strengthened by flanges, and of which one side is lacking, is analyzed by the energy method. The torsional stresses are generally taken up by the bending of the two parallel walls, the rigidity of which is augmented by the third wall. The result was checked experimentally on duralumin and plywood boxes. The torsion recorded was 10 to 30 percent less than that given by the calculation, owing to self-stiffening" (p. 1).

"The present report deals exclusively with the particular jet-propulsion system mentioned in the cited reports. The discussion is limited, for the present, to the analytical study of the efficiency and the consumption for the case of application to aircraft and to the plotting of the practical operating curves secured theoretically by the use of suitable experimental factors" (p. 1).

"Formulas are obtained for computing the buckling load of rods eccentrically loaded at each end, the computation being extended in particular to the inelastic range. The test results are graphically presented on three sets of curves. Two of these, at least for the elastic range, are independent of the material tested. The third set, which is independent of the material, possesses greater clearness and is therefore used for comparing the test results with the theoretical" (p. 1).

Report presenting tables for computing various cases of beam columns in regards to their buckling properties. An explanation of the methods and modulus of buckling under column effect are provided.

"A brief summary of the contents of this paper is presented here. In part I the differential equations of the problem of a gas flow in two dimensions is derived and the particular integrals by which the problem on jets is solved are given. Use is made of the same independent variables as Molenbroek used, but it is found to be more suitable to consider other functions. The stream function and velocity potential corresponding to the problem are given in the form of series" (p. 1).

Predicated on the assumption of certain normal conditions for engine and propeller, simple expressions for the static and dynamic stresses of propeller blade roots are evolved. They, in combination with the fatigue strength diagram of the employed material, afford for each engine power one certain operating point by which the state of stress serving as a basis for the design of the root is defined. Different stress cases must be analyzed, depending on the vibration tendency of engine and use of propeller. The solution affords an insight into the possible introduction of different size classes of propeller.

"The present report deals with the effect of turbulence on the propagation of the flame. Being based upon experiments with laminar as well as turbulent Bunsen flames, both the physico-chemical and the hydro-dynamical aspects of the problem are analyzed. A number of new deductions, interesting from the point of view of engine combustion and other very rapidly changing flame reactions, are made" (p. 1).

"The present report deals with the determination of the impact stresses in the bulkhead floors of a seaplane bottom. The dynamic problem is solved on the assumption of a certain elastic system, the floor being assumed as a weightless elastic beam with concentrated masses at the ends (due to the mass of the float) and with a spring which replaces the elastic action of the keel in the center. The distributed load on the floor is that due to the hydrodynamic force acting over a certain portion of the bottom" (p. 1).

The Russian AM 35 and AM 38 aircraft engines have superchargers with a swirl throttle, which appears to be a purely Russian development. This paper gives the results of test runs of the two engines, including the effects of the swirl throttle on engine performance.

"The present report describes a device for ascertaining the bending and buckling effect in stress measurements on shell structures accessible from one side only. Beginning with a discussion of the relationship between flexural strain and certain parameters, the respective errors of the test method for great or variable skin curvature within the test range are analyzed and illustrated by specimen example" (p. 1).

"In the present paper an investigation is made of two stages of a multistage turboblower having a vaneless diffuser behind the impeller and guide vanes at the inlet to the nest stage. The method employed was that of investigating the performance of the successive elements of the blower (the impeller, vaneless diffuser, ets.) whereby the kinematics of the flow through the blower could be followed and the pressure at the different points computed. The character of the flow and the physical significance of the loss coefficients could thereby be determined so as to secure the best agreement of the computed with the actual performance of the blower" (p. 1).

The purpose of this paper is to explain the differences in thermodynamic qualities of two oils and to try to make this differentiation clear enough so that it can be applied to two oils extremely alike, as, for instance a given oil and the same oil to which a small amount of another substance has been added.

"The present report of Mr. Dupleich is the summary of a very extensive experimental study of the well-known mechanical phenomenon: the rotation in free fall (* air, for instance) of more or less elongated rectangles cut out of paper or pasteboard. This phenomenon, the conditions for existence of which depend chiefly on the elongated of the small plate and its weight per unit area, is essentially an aerodynamic phenomenon and as such, raises questions of a certain interest to our department. We believe that the modern concepts of the mechanics of fluids do not have the range attributed to them" (p. 1).

"In internal combustion engines, steam engines, air compressors, and so forth, the piston ring plays an important role. Especially, the recent development of Diesel engines which require a high compression pressure for their working, makes, nowadays, the packing action of the piston ring far more important than ever. Though a number of papers have been published in regard to researches on the problem of the piston ring, none has yet dealt with an exact measurement of pressure exerted on the cylinder wall at any given point of the ring" (p. 1).

The report is a survey of the strength problems arising on shell and tubular spar wings. The treatment of the shell wing strength is primarily confined to those questions which concern the shell wing only; those pertaining to both shell wing and shell body together have already been treated in TM 838. The discussion of stress condition and compressive strength of shell wings and tubular spar wings is prefaced by several considerations concerning the spar and shell design of metal wings from the point of view of strength.

A calulation of the flow in turbine blading is reported that includes the calculation of effect of centrifugal force. Frictional losses on the stator blades and rotor blades are allowed.

"The method of recording the direction of flows on the basis of the hydrodynamic zero-point measurement has now reached a certain limit, in spite of the good results achieved. While the available flow-direction devices are accurate enough for many purposes, they are all insufficient for perfectly exact prediction of the flow direction. The next problem will be to achieve a point-by point flow-direction record, whereby the test procedure must be simplified, accelerated, and the degree of accuracy of the test data improved" (p. 1).

Axial blowers are gaining importance as aircraft engine superchargers. However, the pressure head obtainable per stage is small. Due to the necessary great number of stages, the physical length of the blower becomes too great for an airworthy device. This report discusses several types of construction that permit a reduction in the length of the blower.

"Considerable progress has, in recent times, been attained in the development of the high-pressure axial blower by well-planned research. The efforts are directed toward improving the efficiencies, which are already high for the axial blower, and in particular the delivery pressure heads. For high pressures multistage arrangements are used. Of fundamental importance is the careful design of all structural parts of the blower that are subject to the effects of the flow. In the present report, several recent results and experiences are reported, which are based on results of German engine research" (p. 1).

From Summary: "The resistance coefficients of commercial types of round wire grids were examined for the purpose of obtaining the necessary data on supercharger test stands for throttling the inducted air to a pressure corresponding to a desired air density. The measurements of the coefficients ranged up to Reynolds numbers of 1000. In the arrangement of two grids in tandem, which was necessary in order to obtain high resistance coefficients with the solidity, that is, mesh density of grid, was found to be accompanied by a further relationship with the mutual spacing of the individual grids."

With the further development of axial blowers into highly loaded flow machines, the influence of the diameter ratio upon air output and efficiency gains in significance. Clarification of this matter is important for single-stage axial compressors, and is of still greater importance for multistage ones, and particularly for aircraft power plants. Tests with a single-stage axial blower gave a decrease in the attainable maximum pressure coefficient and optimum efficiency as the diameter ratio increased. The decrease must be ascribed chiefly to the guide surface of the hub and housing between the blades increasing with the diameter ratio.

The development of suitable thermometer shapes giving the amount of temperature rise if possible without calibration and affording ready repetition is predicated upon a fundamental elucidation of this heating on a number of elementary body forms. This report provides results of tests at subsonic and supersonic velocities.