Report presenting the reverse-thrust performance of several tail-pipe-cascade-type model thrust reversers over a range of exhaust-nozzle pressure ratios from 1.2 to 2.4. Both symmetrical and asymmetrical cascade blade shapes were investigated. Results regarding the performance of tail-pipe-cascade-type model thrust reversers having symmetrically shaped cascade blades and the performance of tail-pipe-cascade-type model thrust reversers having asymmetrically shaped cascade blades are provided.

Report presenting an investigation of a wing swept back 35 degrees in combination with one basic body and three modified bodies at a range of Mach numbers from 0.60 to 1.20. Results regarding force studies and pressure studies are provided. The bodies modified according to the Kuchenmann ring-vortex method resulted in superior aerodynamic characteristics except with regard to zero-lift drag at high supersonic Mach numbers.

Report presenting an investigation of several methods of straightening diffuser-exit total-pressure profiles produced by a typical half-conical double-shock side inlet at a free stream Mach number of 3.05. The methods included the use of longer subsonic diffusers, constant-area mixing sections at the diffuser exit, internal screens, a rapid acceleration of the flow at the diffuser exit, internal bleed, and a change in internal-flow passage shape obtained by raising the internal centerbody fairing from the floor into the diffuser duct. Each of the methods was found to be effective in reducing distortion.

Report discussing testing on a model of the General Electric P-1 nuclear powerplant to determine its internal aerodynamic characteristics. The main purposes of testing were to measure the mass-flow distribution of air, to measure the total-pressure losses for the duct components and complete model, and to determine modifications necessary to attain the desired performance characteristics.

Report presenting an investigation of ram-jet-engine control by shock positioning on a 16-inch fixed-geometry ram jet at a range of free-stream Mach numbers. The control method appears to offer adequate control of ram-jet-engine operation. Results regarding the steady-state performance, effect of control settings on response and stability, effect of disturbance size and Mach number on response to fuel-flow disturbances, Mach number disturbances, angle-of-attack disturbances, exhaust-area disturbances, and recovery from subcritical engine operation are provided.

Report presenting an investigation to determine the pressure drag of various blunt-based conical afterbodies at a range of Mach numbers. A generalized series of bodies was included which incorporated convergent nozzles discharging unheated jets at various pressures from the base. Results regarding the afterbodies without the jet and afterbodies with the jet are provided.

Report discussing testing on a model of the proposed MX-1554A design to determine its stability and control characteristics in high speed flight. Information about the effect of speed brakes, tanks, and fences on the longitudinal characteristics is also provided.

Report presenting theoretical values of rocket performance parameters for two mixtures of liquid ammonia and hydrazine with flourine as oxidant for a variety of parameters. Parameters included are specific impulse, combustion chamber temperature, nozzle-exit temperature, equilibrium composition, mean molecular weight, characteristic velocity, coefficient of thrust, ratio of nozzle-exit area to throat area, specific heat at constant pressure, coefficient of viscosity, and coefficient of thermal conductivity.

Report presenting the effects of a straightening operation on the life of Inconel 500 buckets in a J33-9 engine. Results regarding engine performance and bucket-failure mechanism are provided.

Report presenting the typical effects of flow distortions on turbojet-engine performance and how flow distortions can be reduced by reducing the distortion entering the inlet diffuser and by improving the amount of mixing that generally occurs in the subsonic diffuser. Sources of distortion in the supersonic inlet are described and steps are suggested that might be taken to reduce their effects.

Memorandum presenting the design of a piloted combustor intended for a ramjet engine of long flight range. The unit comprises a large annular basket of V-type cross section, the inner surface of which is slotted and bent into small V-gutters.

Report discussing the characteristics of the fuel control of the 48-inch diameter WRJ47-W-5 ramjet engine, including the time history of the fuel system pressures, fuel flow, and engine inlet total pressure. Oscillograph traces for the different variables are provided as well as the accuracy of the calibration factors.

Report presenting an investigation in the altitude test chamber to evaluate the performance of an axial-flow turbojet engine over a range of engine-inlet Reynolds number indices. Secondary effects of exhaust-nozzle flow coefficient, air-flow leakage, and inlet temperature should be considered before analyzing the effect of variations in engine-inlet Reynolds number index. Several minor design modifications proposed by the manufacturer did not produce any measurable improvement in engine performance.

Report presenting a flight investigation using a rocket-powered model to evaluate the roll-rate stabilization of the Naval Ordnance Test Station SIDEWINDER missile, which uses aerodynamic damping by gyro-actuated rollerons. Dynamic roll instability was found to occur in flight.

Report discussing heat-transfer and pressure measurements obtained from flight testing of a model of the Titan intercontinental ballistic missile up to a specified Mach and Reynolds number. The heat-transfer coefficients were compared to theoretical results and a discrepancy was found during the accelerating portions of flight. Drag coefficients were obtained for a range of Mach numbers.

Report discussing a study of the effects of puncturing the heat shield of an intercontinental-ballistic-missile warhead by small projectiles. Calculations were created for both rod and sphere projectiles and experimental testing was performed on a missile model with holes drilled in the heat shield. The possibility that a projectile could have enough energy to cause mechanical damage to the interior of the warhead is also presented.

Report discussing an investigation of the thermal stabilities of a commercial grade of ethyl decaborane and decaborane at two temperatures. Equations developed from the results of the experiment are also provided. Ethyl decaborane was found to be more stable to pyrolysis than pentaborane but less stable than decaborane.

"The rotating multicylinder method for in-flight determination of liquid-water content, droplet size, and droplet-size distribution in icing clouds is described. The theory of operation, the apparatus required, the technique of obtaining data in flight, and detailed methods of calculating the results, including necessary charts and tables, are presented" (p. 1).

Report presenting an investigation of a shock-positioning control on a 16-inch ramjet engine at a range of Mach numbers and angles of attack in the supersonic wind tunnel. The control operated at all conditions under which the engine could be manually operated. Prediction of the control-system dynamic behavior can be applied by treating the system as having pure dead time.

Report discussing a flight test on a rocket-boosted canard aircraft with 60 degree delta lifting surfaces, twin normal-shock-type side inlets, and twin vertical tails. The drag, longitudinal stability, and duct performance data were obtained for a range of Mach and Reynolds numbers.

Report presenting data to determine the component and overall engine performance up to an altitude limit for the J71-A-11 (600-B36) turbojet engine. Engine operation using JP-4 fuel at Mach number 0.8 was satisfactory up to an altitude of about 60,000 to 65,000 feet, and engine operation with marginal combustion stability was maintained to an altitude of about 80,000 feet. Results regarding the altitude operating limits, component performance, overall engine performance, contribution of individual component losses to overall engine performance losses, exhaust-nozzle-area requirements, and altitude performance at rated engine conditions are provided.

Memorandum presenting a theory for evaluating the mutual interference between a wing and tip tank as extended to apply to store-pylon configurations. By using the theory and the flow-field formulas of a previous report, theoretical store-pylon side-force estimates have been made for a number of store-pylon configurations. Results regarding the theory for store-pylon side force, scope of test configurations, contribution of store and pylon to combined load, effect of store spanwise location on the store-pylon side-force coefficient, effect of pylon sweep and store chordwise location, effect of sideslip on the store-pylon side-force coefficient, effect of fins on store side-force coefficient, and interference effects between inboard and outboard stores are provided.

Memorandum presenting a comparison between the time history of skin temperature measured on the nose of a V-2 and the temperature computed using Eber's experimental relation for heat-transfer coefficients for conical bodies under supersonic conditions. A general method developed for making skin-temperature calculations is used to compute the variation of skin temperature with time for a wide range of values of the pertinent parameters. Results regarding the validity of skin-temperature calculations, ranges of skin temperature, and skin temperatures for a typical supersonic airplane are provided.

Report presenting an investigation in the 4- by 4-foot supersonic tunnel to determine the static longitudinal stability and control characteristics of a supersonic aircraft configuration at a Mach number of 1.59. The model had a 40 degree sweptback tapered wing with 10-percent-thick circular-arc sections normal to the quarter-chord line.